Home › Engine / Hybrid System › 1GR-FE (FUEL) › FUEL FILTER
RM38G0E _51 Engine / Hybrid System _101386 1GR-FE FUEL _0470055 FUEL FILTER A

1GR-FE FUEL  FUEL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel filter removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 77020A 4.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 83320 5.REMOVE FUEL SENDER GAUGE ASSEMBLY

Hide 77024A 6.REMOVE FUEL SUCTION PLATE SUB-ASSEMBLY

Hide 77131C 7.REMOVE NO. 1 FUEL SUB-TANK

Hide 77174 8.REMOVE NO. 1 FUEL SUCTION SUPPORT

Hide 23220A 9.REMOVE FUEL WITH FILTER PUMP ASSEMBLY

Hide 23070 10.REMOVE FUEL MAIN VALVE ASSEMBLY

Hide 23070 11.INSTALL FUEL MAIN VALVE ASSEMBLY

Hide 23220A 12.INSTALL FUEL WITH FILTER PUMP ASSEMBLY

Hide 77174 13.INSTALL NO. 1 FUEL SUCTION SUPPORT

Hide 77131C 14.INSTALL NO. 1 FUEL SUB-TANK

Hide 77024A 15.INSTALL FUEL SUCTION PLATE SUB-ASSEMBLY

Hide 83320 16.INSTALL FUEL SENDER GAUGE ASSEMBLY

Hide 77020A 17.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 19. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART