| *A | for LH Side | *B | for RH Side |
| *C | w/ Rear No. 2 Seat | *D | w/ Tonneau Cover |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 9 | REAR FLOOR MAT REAR SUPPORT PLATE | 58574G | - | - | - |
| 10 | REAR DECK FLOOR BOX | 64993 | - | - | - |
| 11 | REAR FLOOR REAR BOARD LH | 58418H | - | - | - |
| 12 | REAR FLOOR REAR BOARD RH | 58417B | - | - | - |
| 13 | DECK BOARD ASSEMBLY | 58410B | - | - | - |
| 14 | REAR DECK TRIM COVER | 64716P | - | - | - |
| 15 | ROPE HOOK ASSEMBLY | 66310N | - | - | - |
| *A | w/o Rear No. 2 Seat | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| *A | w/ Rear No. 2 Seat | *B | w/o Rear No. 2 Seat |
| *C | w/ Tonneau Cover | - | - |
Use the same procedure for the LHD and RHD vehicles.
The procedure listed below is for the LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
89860C 1.INSTALL NO. 2 SIDE AIRBAG SENSOR ASSEMBLY
| *a | Turns off | - | - |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Perform the following procedure to install the No. 2 side airbag sensor assembly.
1. Engage the guide to hold the No. 2 side airbag sensor assembly in place.
If the No. 2 side airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
When installing the No. 2 side airbag sensor assembly, make sure that the wire harness does not interfere with or is not pinched between other parts.
Make sure that the No. 2 side airbag sensor assembly guide is securely inserted into the body hole.
2. Install the No. 2 side airbag senssor assembly with the bolt.
Tighten the bolt while holding the No. 2 side airbag sensor assembly because the No. 2 side airbag sensor assembly guide is easily damaged.
3. Check that there is no looseness in the installed parts of the No. 2 side airbag sensor assembly.
4. Connect the airbag connector.
When connecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR
62520B 2.INSTALL QUARTER TRIM PANEL ASSEMBLY LH (for LH Side)
62510M 3.INSTALL QUARTER TRIM PANEL ASSEMBLY RH (for RH Side)
64937A 4.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)
73570 5.INSTALL REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) (w/ Rear No. 2 Seat)
73370C 6.INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)
73233D 7.INSTALL OUTER LAP BELT ANCHOR COVER
67918D 8.INSTALL REAR DOOR SCUFF PLATE LH
58574G 9.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
64993 10.INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)
58418H 11.INSTALL REAR FLOOR REAR BOARD LH (w/o Rear No. 2 Seat)
58417B 12.INSTALL REAR FLOOR REAR BOARD RH (w/o Rear No. 2 Seat)
58410B 13.INSTALL DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)
64716P 14.INSTALL REAR DECK TRIM COVER (w/o Rear No. 2 Seat)
66310N 15.INSTALL ROPE HOOK ASSEMBLY (w/o Rear No. 2 Seat)
64910M 16.INSTALL TONNEAU COVER ASSEMBLY (w/o Rear No. 2 Seat, w/ Tonneau Cover)
17.INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
for Manual Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat)>INSTALLATION
for Power Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat)>INSTALLATION
18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
for 1GR-FE:
for V35A-FTS:
19. PERFORM DIAGNOSTIC SYSTEM CHECK
20.CHECK SRS WARNING LIGHT
21. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART