| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | INNER NO. 2 ROOF SIDE GARNISH SPACER LH | 62496B | - | - | - |
| 2 | INNER NO. 2 ROOF SIDE GARNISH SPACER RH | 62495B | - | - | - |
| 3 | INNER NO. 1 ROOF SIDE GARNISH SPACER LH | 62496A | - | - | - |
| 4 | INNER NO. 1 ROOF SIDE GARNISH SPACER RH | 62495A | - | - | - |
| 5 | CENTER NO. 2 PILLAR SPACER LH | 62412G | - | - | - |
| 6 | CENTER NO. 2 PILLAR SPACER RH | 62411M | - | - | - |
| 7 | CENTER NO. 1 PILLAR SPACER LH | 62412F | - | - | - |
| 8 | CENTER NO. 1 PILLAR SPACER RH | 62411L | - | - | - |
| *A | w/ Spacer | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 9 | ROOF HEADLINING ASSEMBLY | - | ( ) |
- | - |
| *A | for Normal Roof | *B | for Moon Roof |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| *A | for Dome Type | *B | for Spot Type |
| *C | w/ Rain Sensor | *D | w/ EC Mirror, w/o Pre-collision System |
| *E | w/ Pre-collision System | *F | w/ Overhead Console |
| *G | w/ Vanity Light | - | - |
| *1 | ASSIST GRIP COVER | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 26 | NO. 1 ROOF SIDE RAIL GARNISH LH | 62432B | - | - | - |
| 27 | NO. 1 ROOF SIDE RAIL GARNISH RH | 62431B | - | - | - |
| 28 | INNER ROOF SIDE GARNISH LH | 62472A | - | - | - |
| 29 | INNER ROOF SIDE GARNISH RH | 62471A | - | - | - |
| 30 | QUARTER PILLAR GARNISH LH | 62582E | - | - | - |
| 31 | QUARTER PILLAR GARNISH RH | 62581E | - | - | - |
| 32 | QUARTER TRIM PANEL ASSEMBLY LH | 62520B | - | - | - |
| 33 | QUARTER TRIM PANEL ASSEMBLY RH | 62510M | - | - | - |
| 34 | NO. 1 TONNEAU COVER HOLDER CAP | 64937A | - | - | - |
| 35 | REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) | 73570 | - | - | - |
| 36 | REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR) | 73560 | - | - | - |
| 37 | REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) | 73370C | - | - | - |
| 38 | REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR) | 73360C | - | - | - |
| 39 | OUTER LAP BELT ANCHOR COVER (for Rear No. 1 Seat) | 73233D | - | - | - |
| *A | w/ Rear No. 2 Seat | *B | w/ Tonneau Cover |
| *C | w/ Curtain Shield Airbag | *D | w/ Rear No. 2 Seat, Curtain Shield Airbag |
| ● | Non-reusable part | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | - | - |
| *A | w/ Curtain Shield Airbag | - | - |
| ● | Non-reusable part | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 58 | REAR FLOOR MAT REAR SUPPORT PLATE | 58574G | - | - | - |
| 59 | REAR DECK FLOOR BOX | 64993 | - | - | - |
| 60 | REAR FLOOR BOARD REAR LH | 58418H | - | - | - |
| 61 | REAR FLOOR BOARD REAR RH | 58417B | - | - | - |
| 62 | DECK BOARD ASSEMBLY | 58410B | - | - | - |
| 63 | REAR DECK TRIM COVER | 64716P | - | - | - |
| 64 | ROPE HOOK ASSEMBLY | 66310N | - | - | - |
| 65 | TONNEAU COVER ASSEMBLY | 64910M | - | - | - |
| *A | w/o Rear No. 2 Seat | *B | w/ Tonneau Cover |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| *A | w/ Rear No. 2 Seat | - | - |
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
62496B 1.INSTALL INNER NO. 2 ROOF SIDE GARNISH SPACER LH (w/ Spacer)
62495B 2.INSTALL INNER NO. 2 ROOF SIDE GARNISH SPACER RH (w/ Spacer)
62496A 3.INSTALL INNER NO. 1 ROOF SIDE GARNISH SPACER LH (w/ Spacer)
62495A 4.INSTALL INNER NO. 1 ROOF SIDE GARNISH SPACER RH (w/ Spacer)
62412G 5.INSTALL CENTER NO. 2 PILLAR SPACER LH (w/ Spacer)
62411M 6.INSTALL CENTER NO. 2 PILLAR SPACER RH (w/ Spacer)
62412F 7.INSTALL CENTER NO. 1 PILLAR SPACER LH (w/ Spacer)
62411L 8.INSTALL CENTER NO. 1 PILLAR SPACER RH (w/ Spacer)
9.INSTALL ROOF HEADLINING ASSEMBLY
|
Install in this Direction | - | - |
Put the roof headlining assembly into the vehicle through the front door RH as shown in the illustration.
Installation of the roof headlining assembly must be performed by multiple people to prevent deformation of the roof headlining assembly.
Check that the corners of the roof headlining are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.
|
Install in this Direction | - | - |
Install the visor holder base as shown in the illustration.
for Normal Roof:
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Attach the hook as shown in the illustration.
Attach the claw as shown in the illustration.
for Moon Roof:
| *a | Fastener | *b | Hook |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
|
Install in this Direction (3) | - | - |
Attach the hook as shown in the illustration.
Attach the fastener as shown in the illustration.
Attach the claw as shown in the illustration.
|
Install in this Direction | - | - |
Attach the clip and install the roof headlining assembly as shown in the illustration.
for Moon Roof:
Connect the connector.
| *A | w/o Pre-collision System | *B | w/ Pre-collision System |
| *C | w/ EC Mirror | *D | w/ Rain Sensor |
|
Install in this Direction | - | - |
for Front Pillar LH Side:
1. Attach the clamp.
2. Connect the washer hose.
3. Connect the connector.
4. Install the bolt.
for Front Pillar RH Side:
1. Attach the clamp.
2. Attach the connector lock to connect the connector.
for Windshield Glass Side:
1. Connect each connector.
for Rear Pillar RH Side:
1. Connect the washer hose.
2. Attach the clamp.
3. Connect each connector.
74348 10.INSTALL VISOR HOLDER
74320 11.INSTALL VISOR ASSEMBLY LH
74310 12.INSTALL VISOR ASSEMBLY RH
74325 13.INSTALL VISOR BRACKET COVER
87834 14.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror, w/o Pre-collision System)
86466D 15.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)
86466E 16.INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System)
89943 17.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
81240D 18.INSTALL NO. 2 ROOM LIGHT ASSEMBLY
81360T 19.INSTALL SPOT LIGHT ASSEMBLY (for Spot Type)
81240 20.INSTALL NO. 1 ROOM LIGHT ASSEMBLY (for Dome Type)
81340 21.INSTALL VANITY LIGHT ASSEMBLY (w/ Vanity Light)
81260A 22.INSTALL MAP LIGHT ASSEMBLY (w/ Overhead Console)
74610U 23.INSTALL ASSIST GRIP ASSEMBLY
Install the 2 clips to the assist grip assembly.
Temporarily install the 2 assist grip covers to the assist grip assembly as shown in the illustration.
Use the same procedure described for the opposite side.
|
Install in this Direction | - | - |
Attach the clip to install the assist grip sub-assembly as shown in the illustration.
Attach the clip to install the 4 assist grip covers.
Check that the 4 clips are securely attached.
74610K 24.INSTALL NO. 2 ASSIST GRIP ASSEMBLY LH
Use the same procedure described for the assist grip assembly.
74610B 25.INSTALL NO. 2 ASSIST GRIP ASSEMBLY RH
Use the same procedure described for the assist grip assembly.
62432B 26.INSTALL NO. 1 ROOF SIDE RAIL GARNISH LH
62431B 27.INSTALL NO. 1 ROOF SIDE RAIL GARNISH RH
62472A 28.INSTALL INNER ROOF SIDE GARNISH LH
62471A 29.INSTALL INNER ROOF SIDE GARNISH RH
62582E 30.INSTALL QUARTER PILLAR GARNISH LH
62581E 31.INSTALL QUARTER PILLAR GARNISH RH
62520B 32.INSTALL QUARTER TRIM PANEL ASSEMBLY LH
62510M 33.INSTALL QUARTER TRIM PANEL ASSEMBLY RH
64937A 34.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)
73570 35.INSTALL REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) (w/ Rear No. 2 Seat)
73560 36.INSTALL REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR) (w/ Rear No. 2 Seat)
Use the same procedure described for the LH Side.
73370C 37.INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)
73360C 38.INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)
Use the same procedure described for the LH Side.
73233D 39.INSTALL OUTER LAP BELT ANCHOR COVER (for Rear No. 1 Seat)
62412 40.INSTALL CENTER PILLAR GARNISH LH
62411 41.INSTALL CENTER PILLAR GARNISH RH
62414A 42.INSTALL CENTER PILLAR LOWER GARNISH LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Remove the 2 clips from the center pillar lower garnish LH and install it to the vehicle.
Slide the center pillar lower garnish LH to attach the clip as shown in the illustration.
Attach the clip and claw to install the center pillar lower garnish LH as shown in the illustration.
62413A 43.INSTALL CENTER PILLAR LOWER GARNISH RH
Use the same procedure described for the LH side.
73220 44.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)
73210 45.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)
Use the same procedure described for the LH side.
73233 46.INSTALL OUTER LAP BELT ANCHOR COVER (for Front Seat)
74620A 47.INSTALL REAR ASSIST GRIP ASSEMBLY
74617F 48.INSTALL ASSIST GRIP PLUG A
74617C 49.INSTALL ASSIST GRIP PLUG B
67918D 50.INSTALL REAR DOOR SCUFF PLATE LH
67917C 51.INSTALL REAR DOOR SCUFF PLATE RH
62212B 52.INSTALL FRONT PILLAR GARNISH ASSEMBLY LH
62211U 53.INSTALL FRONT PILLAR GARNISH ASSEMBLY RH
74620G 54.INSTALL FRONT ASSIST GRIP ASSEMBLY
74617A 55.INSTALL ASSIST GRIP PLUG
67914B 56.INSTALL FRONT DOOR SCUFF PLATE LH
67913B 57.INSTALL FRONT DOOR SCUFF PLATE RH
58574G 58.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
64993 59.INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)
58418H 60.INSTALL REAR FLOOR BOARD REAR LH (w/o Rear No. 2 Seat)
58417B 61.INSTALL REAR FLOOR BOARD REAR RH (w/o Rear No. 2 Seat)
58410B 62.INSTALL DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)
64716P 63.INSTALL REAR DECK TRIM COVER (w/o Rear No. 2 Seat)
66310N 64.INSTALL ROPE HOOK ASSEMBLY (w/o Rear No. 2 Seat)
64910M 65.INSTALL TONNEAU COVER ASSEMBLY (w/o Rear No. 2 Seat, w/ Tonneau Cover)
66.INSTALL REAR NO. 2 SEAT ASSEMBLY RH (w/ Rear No. 2 Seat)
Use the same procedure described for the LH side.
67.INSTALL REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat)
for Manual Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat)>INSTALLATION
for Power Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat)>INSTALLATION
68.INSTALL REAR NO. 1 SEAT ASSEMBLY LH
69.INSTALL REAR NO. 1 SEAT ASSEMBLY RH
for 60/40 Split Seat Type RH Side:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)>INSTALLATION
for 40/20/40 Split Seat Type RH Side:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 40/20/40 Split Seat Type RH Side)>INSTALLATION
70.INSTALL FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>INSTALLATION
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSTALLATION
71.INSTALL FRONT SEAT ASSEMBLY RH
Use the same procedure described for the LH side.
72.ADD WINDSHIELD WASHER FLUID
73. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART