Refer to DTC P034011.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P034011
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P034031 | Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal | No camshaft position sensor (for intake camshaft of bank 1) signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic). * |
·
Open or short in camshaft position sensor (for intake camshaft of bank 1) circuit
·
Camshaft position sensor (for intake camshaft of bank 1)
·
Intake camshaft
·
ECM |
Comes on | SAE: P0340 |
| P034531 | Camshaft Position Sensor "A" Bank 2 No Signal | No camshaft position sensor (for intake camshaft of bank 2) signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic). * |
·
Open or short in camshaft position sensor (for intake camshaft of bank 2) circuit
·
Camshaft position sensor (for intake camshaft of bank 2)
·
Intake camshaft
·
ECM |
Comes on | SAE: P0345 |
*: When the engine is being stopped or started automatically by stop and start system control, the ECM does not monitor the camshaft position sensor signal.
Reference: Inspection using an oscilloscope.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P034011
If no pulse signal is transmitted by the camshaft position sensor (for intake camshaft) despite the camshaft rotating, the ECM interprets this as a malfunction of the sensor.
| Required Sensors/Components (Main) | Camshaft position sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine [A].
Idle the engine for 10 seconds or more [B].
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P034031 or P034531.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE, perform steps [B] through [C] again.
Refer to DTC P034011.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P034011
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
| DTC | Suspected Area |
|---|---|
| P034031 | Bank 1 |
| P034531 | Bank 2 |
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
Disconnect the camshaft position sensor (for intake camshaft) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C11,C12)Location & Routingewd_type=routing;type=c,c;code=C11,C12 |
||
| C11-3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| C12-3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| C11-1 (VVR+) - Body ground | Ignition switch ON | 3.0 to 5.5 V |
| C12-1 (VVL+) - Body ground | Ignition switch ON | 3.0 to 5.5 V |
Turn the ignition switch off and wait for at least 30 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C11,C12)Location & Routingewd_type=routing;type=c,c;code=C11,C12 |
||
| C11-3 (VC) - C11-1 (VVR+) | Ignition switch off | 1.425 to 1.575 kΩ |
| C12-3 (VC) - C12-1 (VVL+) | Ignition switch off | 1.425 to 1.575 kΩ |
| C11-2 (VVR-) - Body ground | Always | Below 1 Ω |
| C12-2 (VVL-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Clearance |
Visually check the camshaft position sensor (for intake camshaft) for damage.
Check the camshaft position sensor (for intake camshaft) installation condition.
The camshaft position sensor (for intake camshaft) does not have any damage and is installed properly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the timing rotor of the intake camshaft.
Camshaft timing rotor does not have any cracks or deformation.
Perform "Inspection After Repair" after replacing the intake camshaft.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the camshaft position sensor (for intake camshaft) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C11,C37,C12)Location & Routingewd_type=routing;type=c,c,c;code=C11,C37,C12 |
||
| C11-1 (VVR+) - C37-89 (VV1+) | Always | Below 1 Ω |
| C11-2 (VVR-) - C37-69 (VV1-) | Always | Below 1 Ω |
| C11-3 (VC) - C37-70 (VCV1) | Always | Below 1 Ω |
| C12-1 (VVL+) - C37-88 (VV2+) | Always | Below 1 Ω |
| C12-2 (VVL-) - C37-67 (VV2-) | Always | Below 1 Ω |
| C12-3 (VC) - C37-68 (VCV2) | Always | Below 1 Ω |
| C11-1 (VVR+) or C37-89 (VV1+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C11-2 (VVR-) or C37-69 (VV1-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C11-3 (VC) or C37-70 (VCV1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C12-1 (VVL+) or C37-88 (VV2+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C12-2 (VVL-) or C37-67 (VV2-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C12-3 (VC) or C37-68 (VCV2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG