Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P006D62  Barometric Pressure - Turbocharger/Supercharger Inlet Pressure Correlation Bank 1 Signal Compare Failure  P00F762  Barometric Pressure - Turbocharger/Supercharger Inlet Pressure Correlation Bank 2 Signal Compare Failure  


DESCRIPTION

The No. 1 turbo pressure sensor is installed upstream of the turbocharger compressor and measures the air inlet duct internal pressure with a built-in sensor.

At ignition switch ON or during idling, the No. 1 turbo pressure sensor and the atmospheric pressure sensor built into the ECM are at atmospheric pressure and their output match.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P006D62 Barometric Pressure - Turbocharger/Supercharger Inlet Pressure Correlation Bank 1 Signal Compare Failure Either of the following conditions is met (1 trip detection logic):
·

At ignition switch ON or during idling, if the difference in atmospheric pressure values is the threshold or greater when the output values from the No. 1 turbo pressure sensor (bank 1) and the atmospheric pressure sensor are compared.

·

The deviation between the air cleaner pressure loss calculated from the atmospheric pressure and No. 1 turbo pressure sensor (bank 1) and the air cleaner pressure loss estimated from the mass air flow meter sub-assembly (bank 1) is at the threshold or higher.


·

No. 1 turbo pressure sensor (bank 1)

·

Mass air flow meter sub-assembly

·

Wire harness or connector

·

Intake system

·

ECM


- SAE: P006D
P00F762 Barometric Pressure - Turbocharger/Supercharger Inlet Pressure Correlation Bank 2 Signal Compare Failure Either of the following conditions is met (1 trip detection logic):
·

At ignition switch ON or during idling, if the difference in atmospheric pressure values is the threshold or greater when the output values from the No. 1 turbo pressure sensor (bank 2) and the atmospheric pressure sensor are compared.

·

The deviation between the air cleaner pressure loss calculated from the atmospheric pressure and No. 1 turbo pressure sensor (bank 2) and the air cleaner pressure loss estimated from the mass air flow meter sub-assembly (bank 2) is at the threshold or higher.


·

No. 1 turbo pressure sensor (bank 2)

·

Mass air flow meter sub-assembly

·

Wire harness or connector

·

Intake system

·

ECM


- SAE: P00F7

MONITOR DESCRIPTION

At ignition switch ON or during idling, if the difference in atmospheric pressure values is the threshold or greater when the output values from the No. 1 turbo pressure sensor and the atmospheric pressure sensor built into the ECM are compared, or if the deviation between the air cleaner pressure loss calculated from the atmospheric pressure and No. 1 turbo pressure sensor and the air cleaner pressure loss estimated from the mass air flow meter sub-assembly is at the threshold or higher while driving (example: when the intake air volume is 40 gm/sec, the value obtained by subtracting the atmospheric pressure from the No. 1 turbo pressure sensor value is larger than 9.27 kPa [1.35 psi] or less than -11.61 kPa [-1.68 psi]), the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

WIRING DIAGRAM

Refer to DTC P010012 for the mass air flow meter sub-assembly circuit.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P010012

Refer to DTC P012A11 for the No. 1 turbo pressure sensor circuit.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P012A11

CONFIRMATION DRIVING PATTERN

A414226E02
0.719,0.677 1.469,0.896 0.75,0.219 10 false 40 km/h 0.885,2.167 1.406,2.406 0.521,0.24 10 false Idling 0.375,2.51 1.302,2.896 0.927,0.385 10 false Ignition switch ON 1.677,3.208 2.906,3.458 1.229,0.25 10 false 5 seconds or more 5.458,3.354 5.896,3.677 0.438,0.323 10 false [D] 3.573,3.219 4.802,3.469 1.229,0.25 10 false 5 seconds or more 1.604,2.344 2.125,2.583 0.521,0.24 10 false [A] 2.177,2.073 2.698,2.313 0.521,0.24 10 false [B] 4.052,0.51 4.573,0.75 0.521,0.24 10 false [C]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and wait 5 seconds or more [B].

7.

Drive the vehicle at 40 km/h (25 mph) for 5 seconds or more [C].

8.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P006D62 and P00F762.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P006D62 Bank 1
P00F762 Bank 2



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P006D62 AND/OR P00F762)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P006D62 and/or P00F762 is output A
P006D62 and/or P00F762 and other DTCs are output B


HINT:

If any DTCs other than P006D62 and/or P00F762 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (TURBOCHARGER/SUPERCHARGER INLET PRESSURE BANK1, TURBOCHARGER/SUPERCHARGER INLET PRESSURE BANK2 AND ATMOSPHERIC PRESSURE)

B

GO TO DTC CHART

2.READ VALUE USING GTS (TURBOCHARGER/SUPERCHARGER INLET PRESSURE BANK1, TURBOCHARGER/SUPERCHARGER INLET PRESSURE BANK2 AND ATMOSPHERIC PRESSURE)
a.

Compare Turbocharger/Supercharger Inlet Pressure Bank1 or Turbocharger/Supercharger Inlet Pressure Bank2 and Atmospheric Pressure in the Data List.

Powertrain > Engine > Data List
Tester Display
Atmospheric Pressure
Turbocharger/Supercharger Inlet Pressure Bank1
Turbocharger/Supercharger Inlet Pressure Bank2
50003 372 229,791,792

Result:
Result Proceed to
Difference between Turbocharger/Supercharger Inlet Pressure Bank1 or Turbocharger/Supercharger Inlet Pressure Bank2 and Atmospheric Pressure in the Data List exceeds 7.1 kPa [1.03 psi] A
Other than above B



A

3.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)

B

7.CHECK INTAKE SYSTEM
3.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)
a.

Using the table, read the normal atmospheric pressure value for the applicable altitude and temperature.

Powertrain > Engine > Data List
Tester Display
Atmospheric Pressure
50003 372 229
A479641C01
0.177,0.063 0.49,0.26 0.313,0.198 10 false *a 0.396,0.51 0.708,0.708 0.313,0.198 10 false *b 2.719,0.51 3.031,0.708 0.313,0.198 10 false *b 5.031,0.51 5.344,0.708 0.313,0.198 10 false *b 1.146,0.51 1.458,0.708 0.313,0.198 10 false *c 3.438,0.5 3.75,0.698 0.313,0.198 10 false *c 5.729,0.5 6.042,0.698 0.313,0.198 10 false *c 1.802,0.5 2.115,0.698 0.313,0.198 10 false *d 4.125,0.51 4.438,0.708 0.313,0.198 10 false *d 6.396,0.521 6.708,0.719 0.313,0.198 10 false *d
*a Altitude, Temperature and Atmospheric Pressure Correlation Table *b Altitude (m (ft.))
*c Temperature (°C (°F)) *d Atmospheric Pressure (kPa (psi))


HINT:
·

Standard atmospheric pressure is approximately 101 kPa(abs) [14.65 psi(abs)].

·

For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa [0.15 psi]. This varies by weather.




b.

Compare the Atmospheric pressure value in the Data List with the normal atmospheric value from the table.

Result:
Result Proceed to
Other than the following A
Difference between Atmospheric Pressure in the Data List and normal atmospheric pressure value is 10 kPa (1.45 psi) or more. B




A

4.CLEAR DTC

B

4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.READ OUTPUT DTC
5.READ OUTPUT DTC
a.

Remove the No. 1 turbo pressure sensor, switch bank 1 and bank 2, and then install the No. 1 turbo pressure sensor.


b.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
A bank DTC different from the one shown in step 1 is output A
Other than above B



A

REPLACE NO. 1 TURBO PRESSURE SENSOR

B

6.CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)
6.CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the No. 1 turbo pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C23,C38,C22)Location & Routing

Click Connector(C23)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>E.F.I. Vacuum Sensor Assembly RH

Click Connector(C38)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C22)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>E.F.I. Vacuum Sensor Assembly LH

C23-3 (VC) - C38-46 (VCPC) Always Below 1 Ω
C23-2 (PIC) - C38-42 (PIC) Always Below 1 Ω
C23-1 (E2) - C38-45 (EPIC) Always Below 1 Ω
C22-3 (VC2) - C38-44 (VPC2) Always Below 1 Ω
C22-2 (PIC2) - C38-41 (PIC2) Always Below 1 Ω
C22-1 (E22) - C38-43 (EPC2) Always Below 1 Ω
C23-3 (VC) or C38-46 (VCPC) - Body ground and other terminals Always 10 kΩ or higher
C23-2 (PIC) or C38-42 (PIC) - Body ground and other terminals Always 10 kΩ or higher
C22-3 (VC2) or C38-44 (VPC2) - Body ground and other terminals Always 10 kΩ or higher
C22-2 (PIC2) or C38-41 (PIC2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK INTAKE SYSTEM
a.

Check that there is no air suction or blockage at any points in the intake system.

Click hereEngine / Hybrid System>V35A-FTS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No air suction or blockage.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (MAF SENSOR)

NG

REPAIR OR REPLACE INTAKE SYSTEM

8.READ VALUE USING GTS (MAF SENSOR)
a.

Start the engine.


b.

Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.


c.

Read Mass Air Flow Sensor with the engine speed at 3000 rpm.

Powertrain > Engine > Data List
Tester Display
MAF Sensor Bank1
MAF Sensor Bank2
50003 372 611,612
Standard:
GTS Display Condition Specified Condition
MAF Sensor Bank1 Engine warmed up
Shift position: N
A/C: Off
Engine Speed: 3000 rpm
Between 6.5 and 30.0 gm/sec
MAF Sensor Bank2 Between 6.5 and 30.0 gm/sec



Result:
Proceed to
OK
NG



OK

9.INSPECT NO. 1 TURBO PRESSURE SENSOR

NG

14.CHECK HARNESS AND CONNECTOR
9.INSPECT NO. 1 TURBO PRESSURE SENSOR

OK

10.CLEAR DTC

NG

12.CHECK HARNESS AND CONNECTOR
10.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P006D62 AND/OR P00F762)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P006D62 AND/OR P00F762)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Perform the All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 1020

c.

Input the DTC: P006D62 and/or P00F762.


d.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(P006D62 and/or P00F762 is output)
B




A

END

B

12.CHECK HARNESS AND CONNECTOR
a.

Disconnect the No. 1 turbo pressure sensor connector.


b.

Turn the ignition switch to ON.



d.

Turn the ignition switch off and wait for at least 30 seconds.



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 TURBO PRESSURE SENSOR

NG

13.CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)
13.CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)
a.

Disconnect the No. 1 turbo pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C23,C38,C22)Location & Routing

Click Connector(C23)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>E.F.I. Vacuum Sensor Assembly RH

Click Connector(C38)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C22)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>E.F.I. Vacuum Sensor Assembly LH

C23-3 (VC) - C38-46 (VCPC) Always Below 1 Ω
C23-2 (PIC) - C38-42 (PIC) Always Below 1 Ω
C23-1 (E2) - C38-45 (EPIC) Always Below 1 Ω
C22-3 (VC2) - C38-44 (VPC2) Always Below 1 Ω
C22-2 (PIC2) - C38-41 (PIC2) Always Below 1 Ω
C22-1 (E22) - C38-43 (EPC2) Always Below 1 Ω
C23-3 (VC) or C38-46 (VCPC) - Body ground and other terminals Always 10 kΩ or higher
C23-2 (PIC) or C38-42 (PIC) - Body ground and other terminals Always 10 kΩ or higher
C22-3 (VC2) or C38-44 (VPC2) - Body ground and other terminals Always 10 kΩ or higher
C22-2 (PIC2) or C38-41 (PIC2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C24,C25)Location & Routing

Click Connector(C24)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly RH

Click Connector(C25)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly LH

C24-4 (VCCR) - C24-3 (FGR) Ignition switch off 2.09 to 2.31 kΩ
C25-4 (VCC) - C25-3 (FG) Ignition switch off 2.09 to 2.31 kΩ
C24-2 (E2GR) - Body ground Always Below 1 Ω
C25-2 (E2G) - Body ground Always Below 1 Ω


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C24,C37,C25)Location & Routing

Click Connector(C24)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly RH

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C25)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Intake Mass Air Flow Meter Sub-Assembly LH

C24-4 (VCCR) - C37-84 (VCVG) Always Below 1 Ω
C24-3 (FGR) - C37-78 (VG) Always Below 1 Ω
C24-2 (E2GR) - C37-83 (E2G) Always Below 1 Ω
C25-4 (VCC) - C37-82 (VVG2) Always Below 1 Ω
C25-3 (FG) - C37-76 (VG2) Always Below 1 Ω
C25-2 (E2G) - C37-81 (E2G2) Always Below 1 Ω
C24-4 (VCCR) or C37-84 (VCVG) - Body ground and other terminals Always 10 kΩ or higher
C24-3 (FGR) or C37-78 (VG) - Body ground and other terminals Always 10 kΩ or higher
C25-4 (VCC) or C37-82 (VVG2) - Body ground and other terminals Always 10 kΩ or higher
C25-3 (FG) or C37-76 (VG2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR