Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P23AA72  Turbocharger/Supercharger Bypass Valve "A" Actuator Stuck Open  P2C2972  Turbocharger/Supercharger Bypass Valve "B" Actuator Stuck Open  


DESCRIPTION

Refer to DTC P003312.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>P003312

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P23AA72 Turbocharger/Supercharger Bypass Valve "A" Actuator Stuck Open Both of the following conditions are met (1 trip detection logic):
·

Accelerator pedal is fully released while the vehicle is stopped after engine warm-up

·

Counter-electromotive force is not generated in the operation current when the air by-pass valve assembly (bank 1) is opened


·

Open or short in air by-pass valve assembly (bank 1) circuit

·

Air by-pass valve assembly (bank 1)

·

EFI MAIN NO. 3 relay

·

ECM


- SAE: P23AA
P2C2972 Turbocharger/Supercharger Bypass Valve "B" Actuator Stuck Open Both of the following conditions are met (1 trip detection logic):
·

Accelerator pedal is fully released while the vehicle is stopped after engine warm-up

·

Counter-electromotive force is not generated in the operation current when the air by-pass valve assembly (bank 2) is opened


·

Open or short in air by-pass valve assembly (bank 2) circuit

·

Air by-pass valve assembly (bank 2)

·

EFI MAIN NO. 3 relay

·

ECM


- SAE: P2C29

MONITOR DESCRIPTION

Air By-pass Valve Assembly Stuck Open

When the accelerator pedal is fully released while the vehicle is stopped after engine warm-up, the ECM opens and closes the air by-pass valve assembly and checks the operation.

At that time, if the operating current value when the air by-pass valve assembly is opened differs from the normal state, the ECM judges that the air by-pass valve assembly is stuck open and stores a DTC.


CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON.

8.

Turn the GTS on.

9.

Start the engine.

10.

Idle the engine for 1 minute or more.

11.

Enter the following menus: Powertrain / Engine / Trouble Codes.

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P23AA72 or P2C2972.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

DTC Suspected Area
P23AA72 Bank 1
P2C2972 Bank 2



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P23AA72 OR P2C2972)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P23AA72 or P2C2972 is output A
P23AA72 or P2C2972 and other DTCs are output B


HINT:

If any DTCs other than P23AA72 or P2C2972 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR BYPASS VALVE OR ACTIVATE THE AIR BYPASS VALVE BANK2)

B

GO TO DTC CHART

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR BYPASS VALVE OR ACTIVATE THE AIR BYPASS VALVE BANK2)
a.

Remove the air by-pass valve assembly.

HINT:

Do not disconnect the connector.



b.

Check that the air by-pass valve assembly moves according to the Active Test.

Powertrain > Engine > Active Test
Tester Display
Activate the Air Bypass Valve
50004 372 12
Powertrain > Engine > Active Test
Tester Display
Activate the Air Bypass Valve Bank2
50004 372 61
OK:

Air by-pass valve assembly moves according to the Active Test



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

5.INSPECT AIR BY-PASS VALVE ASSEMBLY
3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (P23AA72 OR P2C2972)
4.CHECK WHETHER DTC OUTPUT RECURS (P23AA72 OR P2C2972)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Perform the All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 1020

c.

Input the DTC: P23AA72 or P2C2972.


d.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(P23AA72 or P2C2972 is output)
B




A

END

B

5.INSPECT AIR BY-PASS VALVE ASSEMBLY
5.INSPECT AIR BY-PASS VALVE ASSEMBLY
a.

Inspect the air by-pass valve assembly, referring to the On-vehicle Inspection for Air by-pass Valve Assembly.

Click hereEngine / Hybrid System>V35A-FTS (INTAKE / EXHAUST)>INTAKE AIR CONTROL VALVE>ON-VEHICLE INSPECTION


b.

Inspect the air by-pass valve assembly, referring to the Inspection for Air by-pass Valve Assembly.

Click hereEngine / Hybrid System>V35A-FTS (INTAKE / EXHAUST)>INTAKE AIR CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR BY-PASS VALVE ASSEMBLY)

NG

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR BY-PASS VALVE ASSEMBLY)

OK

7.CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE ASSEMBLY - ECM)

NG

8.INSPECT EFI MAIN NO. 3 RELAY
7.CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE ASSEMBLY - ECM)
a.

Disconnect the air by-pass valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C41,C37,C42)Location & Routing

Click Connector(C41)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air By-Pass Valve Assembly RH

Click Connector(C37)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

Click Connector(C42)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air By-Pass Valve Assembly LH

C41-1 (ABV) - C37-30 (ABV) Always Below 1 Ω
C42-1 (ABV2) - C37-29 (ABV2) Always Below 1 Ω
C41-1 (ABV) or C37-30 (ABV) - Body ground and other terminals Always 10 kΩ or higher
C42-1 (ABV2) or C37-29 (ABV2) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT EFI MAIN NO. 3 RELAY

OK

9.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF EFI MAIN NO. 3 RELAY)

NG

REPLACE EFI MAIN NO. 3 RELAY

9.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF EFI MAIN NO. 3 RELAY)
a.
A485839C01
0.125,0.125 0.438,0.281 0.313,0.156 10 false *1 2.448,1.313 2.76,1.469 0.313,0.156 10 false *2
*1 No. 2 Engine Room Relay Block and Junction Block Assembly
*2 EFI MAIN NO. 3 Relay


Remove the EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (EFI MAIN NO. 3 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 3 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI MAIN NO. 3 RELAY)

10.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 3 RELAY - BODY GROUND)
a.

Remove the EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI MAIN NO. 3 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 3 RELAY - AIR BY-PASS VALVE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 3 RELAY - AIR BY-PASS VALVE ASSEMBLY)
a.

Remove the EFI MAIN NO. 3 relay from the No. 2 engine room relay block and junction block assembly.


b.

Disconnect the air by-pass valve assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C41,C42)Location & Routing

Click Connector(C41)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air By-Pass Valve Assembly RH

Click Connector(C42)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Air By-Pass Valve Assembly LH

5 (EFI MAIN NO. 3 relay) - C41-2 (+B) Always Below 1 Ω
5 (EFI MAIN NO. 3 relay) - C42-2 (+B) Always Below 1 Ω
5 (EFI MAIN NO. 3 relay) or C41-2 (+B) - Body ground and other terminals Always 10 kΩ or higher
5 (EFI MAIN NO. 3 relay) or C42-2 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN NO. 1 RELAY - EFI MAIN NO. 3 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR