Home › Engine / Hybrid System › V35A-FTS (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100526 V35A-FTS ENGINE CONTROL _0470271 SFI SYSTEM C

V35A-FTS ENGINE CONTROL  SFI SYSTEM  P070513  Transmission Range Sensor "A" Circuit Open  P070562  Transmission Range Sensor "A" Signal Compare Failure  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P070513 Transmission Range Sensor "A" Circuit Open All switches are off simultaneously for NSW, P, R, N and D for 1 minute or more (2 trip detection logic).
·

Open or short in park/neutral position switch assembly circuit

·

Park/Neutral position switch assembly

·

ECM

·

TCM


Comes on SAE: P0705
P070562 Transmission Range Sensor "A" Signal Compare Failure Either of the following conditions A or B is met (2 trip detection logic):
A. One of the following conditions (a), (b) or (c) is met for 2 seconds or more:
(a) Any 2 or more of the following signals are on simultaneously:
·

P input signal

·

R input signal

·

D input signal


(b) Any 2 or more of the following signals are on simultaneously:
·

N input signal

·

R input signal

·

D input signal


(c) Any 2 or more of the following signals are on simultaneously:
·

NSW input signal

·

R input signal

·

D input signal


B. Any of the following conditions is met for 2 seconds or more with the shift lever in M:
·

NSW input signal is on

·

P input signal is on

·

N input signal is on

·

R input signal is on


·

Open or short in park/neutral position switch assembly circuit

·

Park/Neutral position switch assembly

·

Open or short in transmission control switch circuit

·

Transmission control switch

·

ECM

·

TCM


Comes on SAE: P0705

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends a signal to the ECM.

For security, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, R, N, D or M). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will then illuminate the MIL and store a DTC.

MONITOR STRATEGY

Required Sensors/Components Park/Neutral position switch assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON [A].

7.

Turn the GTS on.

8.

Move the shift lever to R and wait 2 seconds or more [B].

9.

Move the shift lever to N and wait 2 seconds or more [C].

10.

Move the shift lever to D and wait 2 seconds or more [D].

11.

Move the shift lever to M and wait 2 seconds or more [E].

12.

Move the shift lever to P and wait 2 seconds or more [F].

13.

Wait 1 minute or more [G].

14.

Enter the following menus: Powertrain / Engine / Trouble Codes [H].

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

17.

Input the DTC: P070513 or P070562.

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [B] through [H] again.




WIRING DIAGRAM

A485556E01
0.448,5.333 2.146,5.604 1.698,0.271 10 false : CAN Communication Line 4.396,2.604 4.833,2.781 0.438,0.177 10 false C36 4.396,2.771 4.833,2.948 0.438,0.177 10 false TCM 5.708,4.51 6.146,4.688 0.438,0.177 10 false B1 6.323,5.115 6.76,5.292 0.438,0.177 10 false ECM 4.677,1.531 5.115,1.708 0.438,0.177 10 false CAN- 4.667,1.073 5.104,1.25 0.438,0.177 10 false CAN+ 6.073,1.083 6.51,1.26 0.438,0.177 10 false CAN+ 6.073,1.542 6.51,1.719 0.438,0.177 10 false CAN- 5.104,0.906 5.542,1.083 0.438,0.177 10 false 18 5.115,1.354 5.552,1.531 0.438,0.177 10 false 19 5.74,0.906 6.177,1.083 0.438,0.177 10 false 28 5.74,1.354 6.177,1.531 0.438,0.177 10 false 27 5.688,1.094 6.125,1.271 0.438,0.177 10 false C38 5.688,1.542 6.125,1.719 0.438,0.177 10 false C38 3.969,0.292 4.167,0.5 0.198,0.208 10 false 35 3.292,0.302 3.49,0.51 0.198,0.208 10 false DL 4.24,1.01 4.438,1.219 0.198,0.208 10 false N 4.25,1.625 4.448,1.833 0.198,0.208 10 false R 4.25,2.219 4.448,2.427 0.198,0.208 10 false P 3.969,1.469 4.167,1.677 0.198,0.208 10 false 34 3.99,2.073 4.188,2.281 0.198,0.208 10 false 15 3.969,0.865 4.167,1.073 0.198,0.208 10 false 16 1.927,3.563 2.365,3.74 0.438,0.177 10 false C34 1.927,3.729 4.51,3.958 2.583,0.229 10 false Park/Neutral Position Switch Assembly 2.708,4.979 3.146,5.156 0.438,0.177 10 false I74*2 2.302,5.167 4.208,5.417 1.906,0.25 10 false Transmission Control Switch 5.708,4.302 5.906,4.51 0.198,0.208 10 false 32 6.083,4.521 6.281,4.729 0.198,0.208 10 false S 3.375,4.375 3.573,4.583 0.198,0.208 10 false S 3.625,4.375 3.823,4.583 0.198,0.208 10 false 5 2.604,4.396 2.802,4.604 0.198,0.208 10 false IG 2.333,4.375 2.531,4.583 0.198,0.208 10 false 4 3.583,0.281 3.781,0.49 0.198,0.208 10 false 7 3.583,0.865 3.781,1.073 0.198,0.208 10 false 9 3.583,1.469 3.781,1.677 0.198,0.208 10 false 1 3.594,2.073 3.792,2.281 0.198,0.208 10 false 6 4.24,0.427 4.438,0.635 0.198,0.208 10 false D 3.292,0.875 3.49,1.083 0.198,0.208 10 false NL 3.313,1.479 3.51,1.688 0.198,0.208 10 false RL 3.302,2.094 3.5,2.302 0.198,0.208 10 false PL 2.594,1.188 2.854,1.396 0.26,0.208 10 false RB 3.333,3.083 3.531,3.292 0.198,0.208 10 false B 2.594,3.083 2.792,3.292 0.198,0.208 10 false L 2.333,3.094 2.531,3.302 0.198,0.208 10 false 5 3.594,3.083 3.792,3.292 0.198,0.208 10 false 4 2.313,1.198 2.51,1.406 0.198,0.208 10 false 2 6.083,3.229 6.521,3.406 0.438,0.177 10 false NSW 5.667,3.219 6.104,3.396 0.438,0.177 10 false C37 5.771,2.99 5.969,3.198 0.198,0.208 10 false 7 0.719,3.219 1.99,3.469 1.271,0.25 10 false to ST NO. 1 Relay 0.219,4.51 2.177,4.708 1.958,0.198 10 false from ECU-IGR NO. 2 Fuse 0.563,1.313 1.99,1.604 1.427,0.292 10 false from BKUP LP Fuse 2.313,4.979 2.75,5.156 0.438,0.177 10 false I73*1 4.573,5.01 5.677,5.198 1.104,0.188 10 false *1: for LHD 4.583,5.333 5.688,5.521 1.104,0.188 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


a.

Read the values displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (N,P Range)
Shift SW Status (S Range)
Shift SW Status (D Range)
50003 372 15,14,13,263,27,28
GTS Display Measurement Item/Range Normal Condition Diagnostic Note
Shift SW Status (P Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


-
Shift SW Status (R Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


-
Shift SW Status (N Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


-
Shift SW Status (N,P Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in N or P

·

OFF: Shift lever not in N or P


-
Shift SW Status (S Range) Transmission control switch status:
ON or OFF
·

ON: Shift lever in M

·

OFF: Shift lever not in M


-
Shift SW Status (D Range) Park/Neutral position switch assembly status:
ON or OFF
·

ON: Shift lever in D or M

·

OFF: Shift lever not in D or M


-



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P070513 OR P070562)
a.

Perform the Health Check using the GTS.


b.

Read the DTCs.

Result:
Result Proceed to
P070513 or P070562 is output A
P070513 or P070562 and other DTCs are output B


HINT:

If any DTCs other than P070513 or P070562 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (SHIFT SW STATUS)

B

GO TO DTC CHART

2.READ VALUE USING GTS (SHIFT SW STATUS)
a.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 373 15,14,13,28
OK:
GTS Display Shift Lever Position Specified Condition
Shift SW Status (P Range) P ON
Except P OFF
Shift SW Status (R Range) R ON
Except R OFF
Shift SW Status (N Range) N ON
Except N OFF
Shift SW Status (D Range) D or M ON
Except D or M OFF



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (NEUTRAL POSITION SW)

NG

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.READ VALUE USING GTS (NEUTRAL POSITION SW)
a.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display
Neutral Position SW
50003 372 20
OK:
GTS Display Shift Lever Position Specified Condition
Neutral Position SW P or N ON
Except P or N OFF



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
4.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))
a.

Read the Data List displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Shift SW Status (S Range)
50003 372 27
OK:
GTS Display Shift Lever Position Specified Condition
Shift SW Status (S Range) M ON
Except M OFF



Result:
Proceed to
OK
NG



OK

NG

5.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)
5.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

OK

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the transmission control switch connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for LHD

Tester Connection Condition Specified Condition

Click Location & Routing(I73,B1)Location & Routing

Click Connector(I73)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transmission Control Switch (Shift Control Unit Assembly)

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

I73-5 (S) - B1-32 (S) Always Below 1 Ω
I73-5 (S) or B1-32 (S) - Body ground and other terminals Always 10 kΩ or higher

for RHD

Tester Connection Condition Specified Condition

Click Location & Routing(I74,B1)Location & Routing

Click Connector(I74)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Transmission Control Switch (Shift Control Unit Assembly)

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

I74-5 (S) - B1-32 (S) Always Below 1 Ω
I74-5 (S) or B1-32 (S) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Turn the ignition switch to ON.



Result:
Proceed to
OK
NG



OK

9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY POWER SOURCE CIRCUIT)

9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)

NG

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C34,C36)Location & Routing

Click Connector(C34)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Park/Neutral Position Switch Assembly

Click Connector(C36)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transmission Control ECU Assembly

C34-7 (DL) - C36-35 (D) Always Below 1 Ω
C34-9 (NL) - C36-16 (N) Always Below 1 Ω
C34-1 (RL) - C36-34 (R) Always Below 1 Ω
C34-6 (PL) - C36-15 (P) Always Below 1 Ω
C34-7 (DL) or C36-35 (D) - Body ground and other terminals Always 10 kΩ or higher
C34-9 (NL) or C36-16 (N) - Body ground and other terminals Always 10 kΩ or higher
C34-1 (RL) or C36-34 (R) - Body ground and other terminals Always 10 kΩ or higher
C34-6 (PL) or C36-15 (P) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR