Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469674 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB413  Outer Mirror Indicator (Module "B" Side) Circuit Open  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH (B) detects an open in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1AB413 Outer Mirror Indicator (Module "B" Side) Circuit Open
Both of the following conditions are met:
·

The blind spot monitor system is on

·

The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator


·

Outer mirror LH (outer rear view mirror indicator LH)

·

Outer mirror retractor LH

·

Harness or connector

·

Outer mirror control ECU assembly LH

·

Blind spot monitor sensor LH (B)


Blind Spot Monitor "B" A

WIRING DIAGRAM

E329056E83
1.583,1.25 1.74,1.448 0.156,0.198 10 false 2 1.583,1.729 1.74,1.927 0.156,0.198 10 false 1 1.375,1.365 1.531,1.563 0.156,0.198 10 false + 1.375,1.823 1.531,2.021 0.156,0.198 10 false - 0.323,2.198 0.979,2.427 0.656,0.229 10 false B 0.323,2.344 2.042,2.74 1.719,0.396 10 false Outer Mirror LH (Outer Rear View Mirror Indicator LH) 0.479,3.385 2.813,3.781 2.333,0.396 10 false Outer Mirror Retractor LH 2.885,1.344 3.354,1.542 0.469,0.198 10 false z10 2.948,1.156 3.417,1.354 0.469,0.198 10 false 8 3.281,1.354 3.75,1.552 0.469,0.198 10 false BSM+ 3.052,3.396 4.646,3.938 1.594,0.542 10 false Outer Mirror Control ECU Assembly LH 4.031,1.375 4.5,1.573 0.469,0.198 10 false BDSL 4.094,1.833 4.563,2.031 0.469,0.198 10 false GND 4.573,1.344 5.042,1.542 0.469,0.198 10 false N1 4.583,1.146 5.052,1.344 0.469,0.198 10 false 13 4.615,1.635 5.083,1.833 0.469,0.198 10 false 7 5.969,1.375 6.438,1.573 0.469,0.198 10 false OMIL 5.781,1.25 6.25,1.448 0.469,0.198 10 false 4 5.885,3.396 6.354,3.594 0.469,0.198 10 false T10 5.885,3.552 7.115,4.177 1.229,0.625 10 false Blind Spot Monitor Sensor LH (B) 2.917,1.625 3.188,1.792 0.271,0.167 10 false 12 3.302,1.802 3.76,1.969 0.458,0.167 10 false BSM- 2.875,1.813 3.344,2.01 0.469,0.198 10 false z10 4.573,1.823 5.042,2.021 0.469,0.198 10 false N1

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Blind Spot Monitor "B" > Trouble Codes
50001 460

Result:
Result Proceed to
C1AB413 is not output A
C1AB413 is output B



A

B

2.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH [B] AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH [B] AND BODY GROUND)

Pre-procedure1

a.

Disconnect the T10 blind spot monitor sensor LH (B) connector.


b.

Disconnect the N1 outer mirror control ECU assembly LH connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(T10,N1)Location & Routing

Click Connector(T10)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor LH

Click Connector(N1)Body>Front Door Wire LH>Outer Mirror Control ECU Assembly LH

T10-4 (OMIL) - N1-13 (BDSL) Always Below 1 Ω
N1-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH

Pre-procedure1

a.
E297461N02
0.26,1.875 0.104,1.875 0.104,1.875 0.302,1.115 true 1.135,1.896 0.979,1.896 0.979,1.896 0.979,1.302 true 1.896,1.781 1.74,1.781 1.74,1.781 1.885,1.083 true 2.833,1.875 2.677,1.875 2.677,1.875 2.146,1.292 true 0.323,1.792 0.938,1.99 0.615,0.198 10 false BSM+ 1.198,1.833 1.813,2.031 0.615,0.198 10 false BSM- 2.927,1.781 3.354,1.969 0.427,0.188 10 false BDSL 1.969,1.698 2.583,1.896 0.615,0.198 10 false GND

Disconnect the outer mirror control ECU assembly LH connectors.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (BDSL) - 8 (BSM+) Always Below 1 Ω
7 (GND) - 12 (BSM-) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

4.INSPECT OUTER MIRROR RETRACTOR LH

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

4.INSPECT OUTER MIRROR RETRACTOR LH

OK

NG

5.INSPECT OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)
5.INSPECT OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

OK

REPLACE OUTER MIRROR RETRACTOR LH

NG

REPLACE OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)