Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM38G0E _56 Audio / Visual / Telematics _100728 PARK ASSIST / MONITORING _0469674 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB513  Outer Mirror Indicator (Module "A" Side) Circuit Open  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH (A) detects an open in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C1AB513 Outer Mirror Indicator (Module "A" Side) Circuit Open
Both of the following conditions are met:
·

The blind spot monitor system is on

·

The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator


·

Outer mirror RH (outer rear view mirror indicator RH)

·

Outer mirror retractor RH

·

Harness or connector

·

Outer mirror control ECU assembly RH

·

Blind spot monitor sensor RH (A)


Blind Spot Monitor "A" A

WIRING DIAGRAM

E329056E84
1.573,1.229 1.729,1.427 0.156,0.198 10 false 2 1.563,1.729 1.833,1.938 0.271,0.208 10 false 1 1.375,1.365 1.531,1.563 0.156,0.198 10 false + 1.375,1.823 1.531,2.021 0.156,0.198 10 false - 0.323,2.198 0.979,2.427 0.656,0.229 10 false A 0.323,2.344 2.052,2.74 1.729,0.396 10 false Outer Mirror RH (Outer Rear View Mirror Indicator RH) 0.521,3.406 2.219,3.688 1.698,0.281 10 false Outer Mirror Retractor RH 2.948,1.156 3.198,1.344 0.25,0.188 10 false 8 2.906,1.625 3.375,1.823 0.469,0.198 10 false 12 3.083,3.406 4.656,4.083 1.573,0.677 10 false Outer Mirror Control ECU Assembly RH 3.99,1.354 4.458,1.552 0.469,0.198 10 false BDSR 4.083,1.823 4.552,2.021 0.469,0.198 10 false GND 4.563,1.344 5.031,1.542 0.469,0.198 10 false M1 4.563,1.813 5.031,2.01 0.469,0.198 10 false M1 4.563,1.146 5.031,1.344 0.469,0.198 10 false 13 4.615,1.625 5.083,1.823 0.469,0.198 10 false 7 5.969,1.365 6.438,1.563 0.469,0.198 10 false OMIR 5.781,1.24 6.25,1.438 0.469,0.198 10 false 4 5.823,3.396 6.292,3.594 0.469,0.198 10 false Q21 5.813,3.583 7.021,4.198 1.208,0.615 10 false Blind Spot Monitor Sensor RH (A) 2.917,1.333 3.719,1.698 0.802,0.365 10 false z9 3.271,1.354 3.771,1.542 0.5,0.188 10 false BSM+ 3.292,1.813 3.771,1.99 0.479,0.177 10 false BSM- 2.906,1.813 3.677,2.094 0.771,0.281 10 false z9

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Blind Spot Monitor "A" > Trouble Codes
50001 461

Result:
Result Proceed to
C1AB513 is not output A
C1AB513 is output B



A

B

2.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH [A] AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH [A] AND BODY GROUND)

Pre-procedure1

a.

Disconnect the Q21 blind spot monitor sensor RH (A) connector.


b.

Disconnect the M1 outer mirror control ECU assembly RH connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Q21,M1)Location & Routing

Click Connector(Q21)Body>Air Conditioning Wiring Harness Assembly / Floor Wire / Step Rear Floor Wire RH / Theft Warning Sensor Cord Sub-Assembly>Blind Spot Monitor Sensor RH

Click Connector(M1)Body>Front Door Wire RH>Outer Mirror Control ECU Assembly RH

Q21-4 (OMIR) - M1-13 (BDSR) Always Below 1 Ω
M1-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None



OK

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH

Pre-procedure1

a.
E297461N04
0.302,1.698 0.167,1.698 0.167,1.698 0.313,1.094 true 1.281,1.917 1.135,1.917 1.135,1.917 0.979,1.292 true 2.844,1.875 2.719,1.875 2.719,1.875 2.167,1.313 true 1.875,1.792 1.75,1.792 1.75,1.792 1.917,1.042 true 1.948,1.708 2.406,1.917 0.458,0.208 10 false GND 0.385,1.615 1,1.813 0.615,0.198 10 false BSM+ 1.313,1.844 1.927,2.042 0.615,0.198 10 false BSM- 2.958,1.781 3.365,1.99 0.406,0.208 10 false BDSR

Disconnect the outer mirror control ECU assembly RH connectors.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (BDSR) - 8 (BSM+) Always Below 1 Ω
7 (GND) - 12 (BSM-) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

c.

None



OK

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

OK

NG

5.INSPECT OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)
5.INSPECT OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

OK

REPLACE OUTER MIRROR RETRACTOR RH

NG

REPLACE OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)