| *1 | BUTYL TAPE | *2 | TUBE JOINT CLIP |
| *3 | NO. 1 FUEL TUBE CLAMP | *4 | GASKET |
| ● | Non-reusable part | - | - |
| *1 | NO. 4 REAR SIDE AIR DUCT | *2 | NO. 6 REAR SIDE AIR DUCT |
| *3 | REAR FLOOR SILENCER | *4 | FRONT FLOOR CARPET ASSEMBLY |
Perform "Inspection After Repairs" after replacing the fuel suction with pump and gauge tube assembly.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
77020A 1.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
|
|
| *a | Protrusion | *b | Notch |
Install a new gasket to the fuel tank sub-assembly.
Align the protrusions of the fuel suction with pump and gauge tube assembly with the notches in the fuel tank sub-assembly.
Be careful not to bend the arm of the fuel sender gauge.
77144 2.INSTALL FUEL PUMP GAUGE RETAINER (for RH Side)
| *a | SST (Plate) | *b | SST (Bolt) |
| *c | SST (Claw) | *d | Insertion Point |
| *e | SST (Handle) | *f | Triangle Mark (Fuel Pump Gauge Retainer) |
| *g | Triangle Mark (Fuel Tank Sub-assembly) | - | - |
While pressing down on the fuel suction with pump and gauge tube assembly, temporarily install the fuel pump gauge retainer.
Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.
Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.
While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).
Install SST (handle) to SST (plate).
Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer is aligned with the triangle mark on the fuel tank sub-assembly to install the fuel suction with pump and gauge tube assembly to the fuel tank sub-assembly.
Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank sub-assembly.
Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.
Do not spin SST too fast or use an impact wrench as this may result in damage to components.
If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.
Make sure that the gasket does not come off.
77209C 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Push the fuel tube joint of the fuel tank main tube sub-assembly, and install the tube joint clip.
| *1 | Tube Joint Clip |
| *a | Nylon Tube |
| *b | Fuel Tube Joint |
| *c | O-ring |
| *d | Correct |
| *e | Incorrect |
Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.
Check that the fuel tube joint is securely inserted to the end.
Check that the tube joint clip is on the collar of the fuel tube joint.
After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.
58325E 4.INSTALL REAR FLOOR SERVICE HOLE COVER (for RH Side)
Remove any remaining butyl tape from the rear floor service hole cover and body.
Install the rear floor service hole cover with new butyl tape.
Securely install the rear floor service hole cover.
Return the rear floor silencer and attach the 2 clips.
Install the No. 4 rear side air duct and No. 6 rear side air duct and attach the 2 clips.
Return the front floor carpet assembly and attach the 6 clips.
67917C 5.INSTALL REAR DOOR SCUFF PLATE RH
67918D 6.INSTALL REAR DOOR SCUFF PLATE LH
71F95 7.INSTALL REAR NO. 4 SEAT PROTECTOR
71695Y 8.INSTALL REAR NO. 3 SEAT PROTECTOR
71695T 9.INSTALL REAR NO. 2 SEAT PROTECTOR
71695S 10.INSTALL REAR NO. 1 SEAT PROTECTOR
79959G 11.INSTALL NO. 2 SEAT NO. 1 LEG COVER RH
79959J 12.INSTALL NO. 2 SEAT NO. 1 LEG COVER LH
58417B 13.INSTALL REAR FLOOR BOARD REAR RH
58418H 14.INSTALL REAR FLOOR BOARD REAR LH
66310N 15.INSTALL ROPE HOOK ASSEMBLY
58410B 16.INSTALL DECK BOARD ASSEMBLY
17.INSTALL REAR NO. 1 SEAT ASSEMBLY
for LH Side:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for LH Side)>INSTALLATION
for 60/40 Split Seat Type RH Side:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)>INSTALLATION
for 40/20/40 Split Seat Type RH Side:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 40/20/40 Split Seat Type RH Side)>INSTALLATION
77310A 18.INSTALL FUEL TANK CAP ASSEMBLY
19.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
20. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
21.INSPECT FOR FUEL LEAK