Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2021.04–2021.07
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Cannot Delete a Fingerprint/All Fingerprints  


DESCRIPTION

If you cannot delete a fingerprint or all fingerprints, there may be a malfunction between the certification ECU (smart key ECU assembly) and engine switch and a malfunction in the engine switch, or a dirty sensor.

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the engine switch, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440
Body Electrical > Main Body > Trouble Codes
50001 449
Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
DTCs are not output A
DTC is output. B



A

2.READ VALUE USING GTS (Fingerprint Authentication Data Fix)

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

2.READ VALUE USING GTS (Fingerprint Authentication Data Fix)
a.

Using the GTS to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fingerprint Authentication Data Fix Engine switch data status No/Yes No: Data not confirmed
Yes: Data confirmed
-
Body Electrical > Entry&Start > Data List
Tester Display
Fingerprint Authentication Data Fix
50003 440 153

OK:

Data confirmation status (fingerprint authentication) is "Yes"


Result:
Proceed to
OK
NG



OK

3.OPERATION CHECK

NG

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH))
3.OPERATION CHECK
a.

Check whether you can proceed to the fingerprint registration screen.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>REGISTRATION


Result:
Result Proceed to
Can proceed to fingerprint registration screen A
Cannot proceed to fingerprint registration screen B



A

4.OPERATION CHECK

B

4.OPERATION CHECK
a.

Check whether you can enter fingerprint registration mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>REGISTRATION


Result:
Result Proceed to
Can enter fingerprint registration mode A
Cannot enter fingerprint registration mode B



A

5.DELETE FINGERPRINTS

B

5.DELETE FINGERPRINTS
a.

Disconnect and then reconnect the negative (-) battery terminal.


b.

Delete fingerprints and then check that operation is normal.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>REGISTRATION


OK:

Registered normally


Result:
Proceed to
OK
NG



OK

END

NG

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH))
a.

Disconnect the I39 connector of the certification ECU (smart key ECU assembly).


b.

Disconnect the I75 connector of the engine switch.



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - BATTERY)
a.

Connect the I39 connector of the certification ECU (smart key ECU assembly).


b.

Connect the I75 connector of the engine switch.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I75)Location & Routing

Click Connector(I75)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Switch (Push Start Switch)

I75-10 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I75)Location & Routing

Click Connector(I75)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Engine Switch (Push Start Switch)

I75-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.OPERATION CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR