| *A | w/ Tonneau Cover | *B | w/ Rear No. 2 Seat |
| *C | w/o Rear No. 2 Seat | *D | w/ Carpet |
| *A | w/ Tonneau Cover | *B | w/ Rear No. 2 Seat |
| *C | w/o Rear No. 2 Seat | - | - |
| *A | w/ Air Duct | - | - |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 3 indoor electrical key antenna assembly removal/installation are shown below.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. PRECAUTION
64910M 2.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
58570C 3.REMOVE REAR FLOOR CARPET ASSEMBLY (w/ Carpet)
58418H 6.REMOVE REAR FLOOR BOARD REAR LH (w/o Rear No. 2 Seat)
58417B 7.REMOVE REAR FLOOR BOARD REAR RH (w/o Rear No. 2 Seat)
58410B 8.REMOVE DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)
64993 9.REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)
10.REMOVE REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat)
for Manual Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat)>REMOVAL
11.REMOVE REAR NO. 2 SEAT ASSEMBLY RH (w/ Rear No. 2 Seat)
Use the same procedure described for the LH side.
12.REMOVE REAR NO. 1 SEAT ASSEMBLY RH
for 60/40 Split Seat Type:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)>REMOVAL
for 40/20/40 Split Seat Type:
Click hereVehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 40/20/40 Split Seat Type RH Side)>REMOVAL
13.REMOVE REAR NO. 1 SEAT ASSEMBLY LH
58574G 14.REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
73233D 15.REMOVE OUTER LAP BELT ANCHOR COVER
73370C 16.REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)
73360C 17.REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR)
Use the same procedure described for the LH side.
73570 18.REMOVE REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) (w/ Rear No. 2 Seat)
73560 19.REMOVE REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (FLOOR ANCHOR) (w/ Rear No. 2 Seat)
Use the same procedure described for the LH side.
67918D 20.REMOVE REAR DOOR SCUFF PLATE LH
67917C 21.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
62520B 23.REMOVE QUARTER TRIM PANEL ASSEMBLY LH
62510M 24.REMOVE QUARTER TRIM PANEL ASSEMBLY RH
71695S 25.REMOVE REAR NO. 1 SEAT PROTECTOR
71695T 26.REMOVE REAR NO. 2 SEAT PROTECTOR
71695Y 27.REMOVE REAR NO. 3 SEAT PROTECTOR
Use the same procedure described for the rear No. 1 seat protector.
71F95 28.REMOVE REAR NO. 4 SEAT PROTECTOR
Use the same procedure described for the rear No. 1 seat protector.
58510D 29.REMOVE FRONT FLOOR CARPET ASSEMBLY
87217K 30.REMOVE REAR NO. 6 SIDE AIR DUCT (w/ Air Duct)
87217G 31.REMOVE REAR NO. 4 SIDE AIR DUCT (w/ Air Duct)
58556C 32.REMOVE REAR FLOOR SILENCER
|
Turn over in this Direction | - | - |
Using a clip remover, detach the 2 clips as shown and disconnect the front of rear floor silencer.
Turn over the rear floor silencer within the range shown in the illustration.
899A0B 33.REMOVE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY