Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P008800  Fuel Rail/System Pressure - Too High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P008800 Fuel Rail/System Pressure - Too High The fuel pressure of the common rail exceeds 285000 kPa (2906.2 kgf/cm2, 41325 psi).
(1 trip detection logic)
·

Pre-stroke control valve (fuel supply pump assembly)

·

Pressure discharge valve (common rail assembly)

·

Open or short in pre-stroke control valve circuit

·

No. 1 injector assembly (fuel pressure sensor)

·

No. 4 injector assembly (fuel pressure sensor)

·

ECM


Comes on SAE Code: P0088

Related Data List
DTC No. Data List
P008800
·

Fuel Pressure (High)

·

Target Fuel Pressure (High)

·

Fuel Pressure #1

·

Fuel Pressure #4



HINT:
·

When DTC P008800 is stored, check the internal fuel pressure of the common rail assembly by entering the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).

Reference
Engine Speed Fuel Pressure (High)
Idling Approximately 25000 to 50000 kPa
3000 rpm (No engine load) Approximately 36000 to 120000 kPa

·

Check "Fuel Pressure (High)" and "Target Fuel Pressure (High)" in the freeze frame data.



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P008800 After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds

MONITOR DESCRIPTION

The ECM stores this DTC if the fuel pressure inside the common rail assembly is higher than 285000 kPa (2906.2 kgf/cm2, 41325 psi). This DTC indicates that: 1) the pre-stroke control valve may be stuck open, or 2) there may be a short in the pre-stroke control valve circuit.

If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P008800)
a.

Read Current DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P008800 is output A
P008800 and DTCs related to the fuel pressure sensor circuit* are output B


HINT:
·

*: Fuel pressure sensor circuit DTC: P13A011, P13A015, P13A02A, P13A511, P13A515, P13A52A, P13AA11, P13AA15, P13AA2A, P13B011, P13B015, P13B02A, P13B511, P13B515, P13B52A, P13BA11, P13BA15, P13BA2A, P13E011, P13E015, P13E511, P13E515.

·

When there is an open circuit in the fuel pressure sensor circuit, the fuel pressure sensor outputs the maximum value. Therefore, P008800 may be stored together with DTCs which indicate common rail fuel pressure sensor circuit malfunctions.





A

2.CHECK FREEZE FRAME DATA (FUEL PRESSURE (HIGH))

B

GO TO FUEL RAIL PRESSURE SENSOR CIRCUIT

2.CHECK FREEZE FRAME DATA (FUEL PRESSURE (HIGH))
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

b.

Record the stored DTCs and freeze frame data.

Result:
Result Proceed to
Value of Fuel Pressure (High) is shifting towards 160000 kPag or higher in 3rd and 4th set of freeze frame data B
Except above A




A

3.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR OUTPUT)

B

5.REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR OUTPUT)
a.

Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High), Fuel Pressure #1 and Fuel Pressure #4.

Powertrain > Engine > Data List
Tester Display
Fuel Pressure (High)
Fuel Pressure #1
Fuel Pressure #4
50003 372 265,1439,1442

b.

Turn the ignition switch to ON.


c.

When the wire harness between the No. 1 injector assembly, No. 4 injector assembly and the ECM is vibrated, check whether the fuel pressure sensor value changes due to vibration or the MIL is illuminated.

A490877C01
3.188,0.406 3.042,0.417 3.042,0.417 2.552,0.844 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 0.885,0.49 1.198,0.688 0.313,0.198 10 false *1 3.271,0.344 3.583,0.542 0.313,0.198 10 false *2 5.302,0.208 5.615,0.406 0.313,0.198 10 false *3 5.5,2.177 5.813,2.375 0.313,0.198 10 false *4
*1 Engine *2 Engine Wire
*3 Wire to Wire *4 ECM
*a Vibration Method (Reference) - -


Result:
Result Proceed to
When the wire harness is vibrated, MIL illuminates or the value of "Fuel Pressure (High)", "Fuel Pressure #1" or "Fuel Pressure #4" on the Data List changes due to vibration B
Except above A




A

4.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE PRE-STROKE CONTROL VALVE)

B

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE PRE-STROKE CONTROL VALVE)
a.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Pre-stroke Control Valve

Powertrain > Engine > Active Test
Tester Display
Activate the Pre-stroke Control Valve
50004 372 42022

b.

Perform the Active Test and check that operation sounds can be heard from the pre-stroke control valve.

HINT:
·

Perform this procedure with the engine stopped and check the operation sounds from outside the vehicle.

·

Check in a quiet location with the hood opened, as the operation sound is difficult to hear.

·

In order to distinguish between the operation sounds of other actuators, check by using the GTS to turn the Active Test open and close several times.

·

This vehicle has 2 pre-stroke control valve systems that operate alternately in 0.5 second intervals.

·

If the operating sound interval is larger than that of a normal vehicle, there may be a malfunction in one of the pre-stroke control valves.



OK:

The operation sound is generated when performing the Active Test, and stops when finished.



Result:
Proceed to
OK
NG



NG

5.REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

OK

8.REPLACE ECM
5.REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.BLEED AIR FROM FUEL SYSTEM
6.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Start the engine.


d.

After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.


e.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 372
HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P008800.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC P008800 is output A
All Readiness NORMAL B
ABNORMAL A


HINT:

If STATUS is INCOMPLETE, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.





A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR OUTPUT)
10.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR OUTPUT)
a.

Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High), Fuel Pressure #1 and Fuel Pressure #4.

Powertrain > Engine > Data List
Tester Display
Fuel Pressure (High)
Fuel Pressure #1
Fuel Pressure #4
50003 372 265,1439,1442

b.

When the wire harness between the No. 1 injector assembly, No. 4 injector assembly and the ECM is vibrated, check whether the fuel pressure sensor value changes due to vibration or the MIL is illuminated.

A490877C01
3.188,0.406 3.042,0.417 3.042,0.417 2.552,0.844 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 0.885,0.49 1.198,0.688 0.313,0.198 10 false *1 3.271,0.344 3.583,0.542 0.313,0.198 10 false *2 5.302,0.208 5.615,0.406 0.313,0.198 10 false *3 5.5,2.177 5.813,2.375 0.313,0.198 10 false *4
*1 Engine *2 Engine Wire
*3 Wire to Wire *4 ECM
*a Vibration Method (Reference) - -


Result:
Result Proceed to
When the wire harness is vibrated, MIL illuminates or the value of "Fuel Pressure (High)", "Fuel Pressure #1" or "Fuel Pressure #4" on the Data List changes due to vibration A
Except above B




A

11.REPLACE INJECTOR ASSEMBLY

B

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE INJECTOR ASSEMBLY
a.

Replace the No. 1 or No. 4 injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

Replace the injection pipe sub-assembly that was removed with a new one.

·

Following the repair manual, temporarily install the injection pipe and after positioning the injector, tighten the injector to the specified torque.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

12.BLEED AIR FROM FUEL SYSTEM
12.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Start the engine.


d.

After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.


e.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P008800.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.



Result:
Proceed to
NEXT



NEXT

END