The ECM detects combustion deterioration for a specific cylinder.
| *1 | Nozzle | *2 | Two-Way Valve |
| *3 | Low Suck Volume Nozzle | *4 | Nozzle Needle |
| *5 |
·
Fuel Pressure Sensor
·
Fuel Temperature Sensor |
- | - |
| *a | Injector Assembly Cross Section Diagram | - | - |
The cylinder which has the compensation value, indicated by Injection Feedback Value #1, #2, #3, #4, #5 and #6, that varies from the other cylinders may be malfunctioning.
If DTC P009300 (fuel leaks from high-pressure area), P029D00, P02A100, P02A500, P02A900, P02AD00, P02B100 (injector leaking) is stored simultaneously, a leakage malfunction of a specific cylinder has probably occurred.
If DTC P020112, P020114, P020212, P020214, P020312, P020314, P020412, P020414, P020512, P020514, P020612, P020614, P062D96 and/or P062E96 (open or short in the injector circuit or ECM internal malfunction) is stored simultaneously, there is probably a faulty circuit located between the ECM and the injector assembly.
If only DTC P030100, P030200, P030300, P030400, P030500 and/or P030600 (injector malfunction) has been stored, an injector assembly mechanical malfunction or insufficient compression (valve clearance, etc.) has probably occurred. An open or short malfunction of the ECM or injector circuit is unlikely.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P030100 | Cylinder 1 Misfire Detected | Injector Feedback Value #1 is 5.0 mm3/st and the engine speed fluctuation of No. 1 cylinder is large during idling. (2 trip detection logic) |
Main Trouble Area
·
No. 1 Injector assembly
·
Compression pressure Related Trouble Area
·
Valve timing
·
Fuel with low cetane number used
·
ECM |
Comes on | SAE Code: P0301 |
| P030200 | Cylinder 2 Misfire Detected | Injector Feedback Value #2 is 5.0 mm3/st and the engine speed fluctuation of No. 2 cylinder is large during idling. (2 trip detection logic) |
Main Trouble Area
·
No. 2 Injector assembly
·
Compression pressure Related Trouble Area
·
Valve timing
·
Fuel with low cetane number used
·
ECM |
Comes on | SAE Code: P0302 |
| P030300 | Cylinder 3 Misfire Detected | Injector Feedback Value #3 is 5.0 mm3/st and the engine speed fluctuation of No. 3 cylinder is large during idling. (2 trip detection logic) |
Main Trouble Area
·
No. 3 Injector assembly
·
Compression pressure Related Trouble Area
·
Valve timing
·
Fuel with low cetane number used
·
ECM |
Comes on | SAE Code: P0303 |
| P030400 | Cylinder 4 Misfire Detected | Injector Feedback Value #4 is 5.0 mm3/st and the engine speed fluctuation of No. 4 cylinder is large during idling. (2 trip detection logic) |
Main Trouble Area
·
No. 4 Injector assembly
·
Compression pressure Related Trouble Area
·
Valve timing
·
Fuel with low cetane number used
·
ECM |
Comes on | SAE Code: P0304 |
| P030500 | Cylinder 5 Misfire Detected | Injector Feedback Value #5 is 5.0 mm3/st and the engine speed fluctuation of No. 5 cylinder is large during idling. (2 trip detection logic) |
Main Trouble Area
·
No. 5 Injector assembly
·
Compression pressure Related Trouble Area
·
Valve timing
·
Fuel with low cetane number used
·
ECM |
Comes on | SAE Code: P0305 |
| P030600 | Cylinder 6 Misfire Detected | Injector Feedback Value #6 is 5.0 mm3/st and the engine speed fluctuation of No. 6 cylinder is large during idling. (2 trip detection logic) |
Main Trouble Area
·
No. 6 Injector assembly
·
Compression pressure Related Trouble Area
·
Valve timing
·
Fuel with low cetane number used
·
ECM |
Comes on | SAE Code: P0306 |
| DTC No. | Data List |
|---|---|
| P030100 P030200 P030300 P030400 P030500 P030600 |
·
Target Injection Volume
·
Injection Feedback Value #1 to #6
·
Fuel Pressure (High)
·
Target Fuel Pressure (High) |
If DTC P030100, P030200, P030300, P030400, P030500 or P030600 is stored, the following symptoms may appear:
Rough idle
Poor driveability
After confirming DTC P030100, P030200, P030300, P030400, P030500 or P030600, check the internal fuel pressure on the GTS by entering the following menus: Powertrain / Engine / Data List / Fuel Pressure (High), Target Fuel Pressure (High).
Under a stable condition such as idling or running the engine at 3000 rpm without load, Fuel Pressure (High) is within 5000 kPa of Target Fuel Pressure (High).
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P030100 P030200 P030300 P030400 P030500 P030600 |
Warm up the engine and idle it for 60 seconds or more |
This DTC will be stored if the engine speed fluctuation between each cylinder is large. The ECM monitors changes in the crankshaft rotation speed using the crankshaft position sensor in order to detect improper combustion. The camshaft position sensor also plays a role in determining which cylinder has the problem. The fluctuation counter increases when irregular crankshaft rotation speed variation exceeds the threshold with the engine idling. Therefore, if any one of the cylinders is operating poorly (rough idle), the ECM stores this DTC.
Refer to DTC P020112.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P020112
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
When this DTC is stored, be sure to carefully examine "Injection Feedback Value #1 to #6", "Target Injection Volume", "Fuel Pressure (High)", "Target Fuel Pressure (High)", "Engine Speed", "Mass Air Flow Sensor", "Coolant Temperature" and "Vehicle Speed" in the freeze frame data.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P030100, P030200, P030300, P030400, P030500 or P030600 is output | A |
| P030100, P030200, P030300, P030400, P030500 or P030600 and other DTCs are output | B |
If any DTCs other than P030100, P030200, P030300, P030400, P030500 or P030600 are output, troubleshoot those DTCs first.
If DTCs other than P030100, P030200, P030300, P030400, P030500 or P030600 are not output, check the fuel condition before proceeding to the next step.
A
B
Check the wire harness and connector connections.
The wire harness and connectors have been connected securely and there are good connections.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus: Powertrain / Engine / Data List / Injection Feedback Value #1 to #6.
| Tester Display |
|---|
| Injection Feedback Value #1 |
| Injection Feedback Value #2 |
| Injection Feedback Value #3 |
| Injection Feedback Value #4 |
| Injection Feedback Value #5 |
| Injection Feedback Value #6 |
Read the value.
The compensatory injection volume is less than 4.9 mm3/st
If the injector assembly is malfunctioning, the compensatory injection volume remains at 5.0 mm3/st.
If there is a disconnection, the feedback value will increase and +5.0 mm3/st will be indicated, because it will become impossible for the injector assembly to inject.
Inspect and repair the cylinder that has an improper compensation value according to the following steps.
| Proceed to |
|---|
| NEXT |
NEXT
Enter the following menus: Powertrain / Engine / Active Test / Control the Select Cylinder Fuel Cut.
| Tester Display |
|---|
| Control the Select Cylinder Fuel Cut |
Check the 6 cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.
If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning.
If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.
| Proceed to |
|---|
| NEXT |
NEXT
Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.
Check the cylinder compression pressure.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the injector assembly.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL INJECTOR>REMOVAL
Replace the injection pipe sub-assembly that was removed with a new one.
Following the repair manual, temporarily install the injection pipe and after positioning the injector, tighten the injector to the specified torque.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Start the engine.
Warm up the engine (engine coolant temperature is 75°C (167°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If no pending DTCs are output, proceed to the next step to check "All Readiness".
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P030100, P030200, P030300, P030400, P030500 or P030600.
Check the DTC judgment result.
| GTS Display | Result | Proceed to |
|---|---|---|
| Pending DTC | DTC P030100, P030200, P030300, P030400, P030500 or P030600 is output | A |
| All Readiness | ABNORMAL | |
| NORMAL | B |
If STATUS is INCOMPLETE, increase the idling time.
A
B
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Start the engine.
Warm up the engine (engine coolant temperature is 75°C (167°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P030100, P030200, P030300, P030400, P030500 or P030600.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE, increase the idling time.
| Proceed to |
|---|
| NEXT |
NEXT