The injector assemblies are installed in the cylinder head and inject fuel into the cylinders based on the signals from the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P020112 | Cylinder 1 Injector "A" Circuit Short to Battery | Short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). (1 trip detection logic) |
·
Short in No. 1 injector assembly circuit
·
No. 1 injector assembly
·
ECM |
Comes on | SAE Code: P0262 |
| P020114 | Cylinder 1 Injector "A" Circuit Short to Ground or Open | Open in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). (1 trip detection logic) |
·
Open in No. 1 injector assembly circuit
·
No. 1 injector assembly
·
ECM |
Comes on | SAE Code: P0261 |
| P020212 | Cylinder 2 Injector "A" Circuit Short to Battery | Short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). (1 trip detection logic) |
·
Short in No. 2 injector assembly circuit
·
No. 2 injector assembly
·
ECM |
Comes on | SAE Code: P0265 |
| P020214 | Cylinder 2 Injector "A" Circuit Short to Ground or Open | Open in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). (1 trip detection logic) |
·
Open in No. 2 injector assembly circuit
·
No. 2 injector assembly
·
ECM |
Comes on | SAE Code: P0264 |
| P020312 | Cylinder 3 Injector "A" Circuit Short to Battery | Short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). (1 trip detection logic) |
·
Short in No. 3 injector assembly circuit
·
No. 3 injector assembly
·
ECM |
Comes on | SAE Code: P0268 |
| P020314 | Cylinder 3 Injector "A" Circuit Short to Ground or Open | Open in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). (1 trip detection logic) |
·
Open in No. 3 injector assembly circuit
·
No. 3 injector assembly
·
ECM |
Comes on | SAE Code: P0267 |
| P020412 | Cylinder 4 Injector "A" Circuit Short to Battery | Short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). (1 trip detection logic) |
·
Short in No. 4 injector assembly circuit
·
No. 4 injector assembly
·
ECM |
Comes on | SAE Code: P0271 |
| P020414 | Cylinder 4 Injector "A" Circuit Short to Ground or Open | Open in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). (1 trip detection logic) |
·
Open in No. 4 injector assembly circuit
·
No. 4 injector assembly
·
ECM |
Comes on | SAE Code: P0270 |
| P020512 | Cylinder 5 Injector "A" Circuit Short to Battery | Short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). (1 trip detection logic) |
·
Short in No. 5 injector assembly circuit
·
No. 5 injector assembly
·
ECM |
Comes on | SAE Code: P0274 |
| P020514 | Cylinder 5 Injector "A" Circuit Short to Ground or Open | Open in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). (1 trip detection logic) |
·
Open in No. 5 injector assembly circuit
·
No. 5 injector assembly
·
ECM |
Comes on | SAE Code: P0273 |
| P020612 | Cylinder 6 Injector "A" Circuit Short to Battery | Short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). (1 trip detection logic) |
·
Short in No. 6 injector assembly circuit
·
No. 6 injector assembly
·
ECM |
Comes on | SAE Code: P0277 |
| P020614 | Cylinder 6 Injector "A" Circuit Short to Ground or Open | Open in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds). (1 trip detection logic) |
·
Open in No. 6 injector assembly circuit
·
No. 6 injector assembly
·
ECM |
Comes on | SAE Code: P0276 |
| P062D96 | Fuel Injector Driver Circuit Performance Bank 1 Component Internal Failure | ECM internal error. (1 trip detection logic) |
ECM | Comes on | SAE Code: P062D |
| P062E96 | Fuel Injector Driver Circuit Performance Bank 2 Component Internal Failure | ECM internal error. (1 trip detection logic) |
ECM | Comes on | SAE Code: P062E |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P020112 P020114 P020212 P020214 P020312 P020314 P020412 P020414 P020512 P020514 P020612 P020614 P062D96 P062E96 |
Idling for 5 seconds or more |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.
Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P020112, P020114, P020212, P020214, P020312, P020314, P020412 or P020414, P020512, P020514, P020612, P020614 is output | A |
| DTC P062D96 or P062E96 is output | B |
A
B
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds.
Start the engine and idle it for 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Check the DTCs output on the GTS.
The cylinder with the malfunctioning injector assembly can be determined based on the output DTCs.
If the DTC P020112 or P020114 is output, check the No. 1 injector assembly circuit.
If the DTC P020212 or P020214 is output, check the No. 2 injector assembly circuit.
If the DTC P020312 or P020314 is output, check the No. 3 injector assembly circuit.
If the DTC P020412 or P020414 is output, check the No. 4 injector assembly circuit.
If the DTC P020512 or P020514 is output, check the No. 5 injector assembly circuit.
If the DTC P020612 or P020614 is output, check the No. 6 injector assembly circuit.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the injector assembly connectors for all cylinders.
If only the injector assembly connector of the malfunctioning cylinder is disconnected, the engine will start and there will be rough idling. Therefore, disconnect all injector assembly connectors before inspecting the waveform.
Start the engine.
Check the waveform of the injector assembly connectors using an oscilloscope.
| *a | Front view of wire harness connector (Injector Assembly) |
*b | No. 1 Injector Assembly Connector |
| *c | No. 2 Injector Assembly Connector | *d | No. 3 Injector Assembly Connector |
| *e | No. 4 Injector Assembly Connector | *f | No. 5 Injector Assembly Connector |
| *g | No. 6 Injector Assembly Connector | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C117,C118,C119,C120,C121,C122)Location & Routingewd_type=routing;type=c,c,c,c,c,c;code=C117,C118,C119,C120,C121,C122 |
||
| C117-6 (#10) - C117-3 (#1) | Cranking | Correct waveform is as shown |
| C118-6 (#20) - C118-3 (#2) | Cranking | Correct waveform is as shown |
| C119-6 (#30) - C119-3 (#3) | Cranking | Correct waveform is as shown |
| C120-6 (#40) - C120-3 (#4) | Cranking | Correct waveform is as shown |
| C121-6 (#50) - C121-3 (#5) | Cranking | Correct waveform is as shown |
| C122-6 (#60) - C122-3 (#6) | Cranking | Correct waveform is as shown |
Reconnect the injector assembly connectors for all cylinders.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the injector assembly of the cylinder relevant to the DTC.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL INJECTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Replace the injector assembly of the cylinder relevant to the DTC.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL INJECTOR>REMOVAL
Replace the injection pipe sub-assembly that was removed with a new one.
Following the repair manual, temporarily install the injection pipe and after positioning the injector, tighten the injector to the specified torque.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C117,C138,C118,C119,C120,C121,C122)Location & Routingewd_type=routing;type=c,c,c,c,c,c,c;code=C117,C138,C118,C119,C120,C121,C122 |
||
| C117-3 (#1) - C138-17 (#1D-) | Always | Below 1 Ω |
| C117-6 (#10) - C138-36 (#1D+) | Always | Below 1 Ω |
| C118-3 (#2) - C138-14 (#2D-) | Always | Below 1 Ω |
| C118-6 (#20) - C138-33 (#2D+) | Always | Below 1 Ω |
| C119-3 (#3) - C138-16 (#3D-) | Always | Below 1 Ω |
| C119-6 (#30) - C138-35 (#3D+) | Always | Below 1 Ω |
| C120-3 (#4) - C138-13 (#4D-) | Always | Below 1 Ω |
| C120-6 (#40) - C138-32 (#4D+) | Always | Below 1 Ω |
| C121-3 (#5) - C138-15 (#5D-) | Always | Below 1 Ω |
| C121-6 (#50) - C138-34 (#5D+) | Always | Below 1 Ω |
| C122-3 (#6) - C138-12 (#6D-) | Always | Below 1 Ω |
| C122-6 (#60) - C138-31 (#6D+) | Always | Below 1 Ω |
| C117-3 (#1) or C138-17 (#1D-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C117-6 (#10) or C138-36 (#1D+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C118-3 (#2) or C138-14 (#2D-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C118-6 (#20) or C138-33 (#2D+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C119-3 (#3) or C138-16 (#3D-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C119-6 (#30) or C138-35 (#3D+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C120-3 (#4) or C138-13 (#4D-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C120-6 (#40) or C138-32 (#4D+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C121-3 (#5) or C138-15 (#5D-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C121-6 (#50) or C138-34 (#5D+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C122-3 (#6) or C138-12 (#6D-) - Body ground and other terminals | Always | 10 kΩ or higher |
| C122-6 (#60) or C138-31 (#6D+) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the EDU relay.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EDU relay from the No. 3 engine room relay block and junction block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C138)Location & Routingewd_type=routing;type=c;code=C138 |
||
| C138-19 (+BD1) - EDU relay terminal 5 | Always | Below 1 Ω |
| C138-38 (+BD2) - EDU relay terminal 5 | Always | Below 1 Ω |
| C138-18 (+BD3) - EDU relay terminal 5 | Always | Below 1 Ω |
| C138-37 (+BD4) - EDU relay terminal 5 | Always | Below 1 Ω |
| C138-19 (+BD1) or EDU relay terminal 5 - Body ground and other terminals | Always | 10 kΩ or higher |
| C138-38 (+BD2) or EDU relay terminal 5 - Body ground and other terminals | Always | 10 kΩ or higher |
| C138-18 (+BD3) or EDU relay terminal 5 - Body ground and other terminals | Always | 10 kΩ or higher |
| C138-37 (+BD4) or EDU relay terminal 5 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EDU relay from the No. 3 engine room relay block and junction block assembly.
| *1 | No. 3 Engine Room Relay Block and Junction Block Assembly |
| *2 | EDU Relay |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EDU relay terminal 3 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EDU relay from the No. 3 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EDU relay terminal 2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EDU relay and EFI MAIN NO. 1 relay from the No. 3 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EDU relay terminal 1 - EFI MAIN NO. 1 relay terminal 5 | Always | Below 1 Ω |
| EDU relay terminal 1 or EFI MAIN NO. 1 relay terminal 5 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Start the engine and idle it for 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the EDU relay.
| Proceed to |
|---|
| NEXT |
NEXT