Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P033511  Crankshaft Position Sensor "A" Circuit Short to Ground  P033515  Crankshaft Position Sensor "A" Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P03351F.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P03351F

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P033511 Crankshaft Position Sensor "A" Circuit Short to Ground Output voltage of crankshaft position sensor is less than 0.3 V for 4 seconds or more.
(1 trip detection logic)
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Comes on SAE Code: P0337
P033515 Crankshaft Position Sensor "A" Circuit Short to Battery or Open Output voltage of crankshaft position sensor is higher than 4.7 V for 4 seconds or more.
(1 trip detection logic)
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Comes on SAE Code: P0338

HINT:

If DTC P033511 or P033515 is stored, the following symptoms may appear:

-

Difficulty starting

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




MONITOR DESCRIPTION

When the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P033511
P033515
Ignition switch ON for 4 seconds or more

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

b.

Record any output DTC(s).


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

d.

Turn the ignition switch off and wait for 30 seconds or more.


e.

Disconnect the crankshaft position sensor connector.


f.

Turn the ignition switch to ON and wait for 4 seconds or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Check whether the DTC changes when the connector is disconnected and connected.

Result:
Result Proceed to
DTC does not change A
DTC changes B




A

2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

B

5.REPLACE CRANKSHAFT POSITION SENSOR
2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C146,C138)Location & Routing

Click Connector(C146)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Crank Position Sensor

Click Connector(C138)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C146-3 (VC) - C138-109 (VCNE) Always Below 1 Ω
C146-1 (NE+) - C138-62 (NE+) Always Below 1 Ω
C146-2 (NE-) - C138-108 (NE-) Always Below 1 Ω
C146-3 (VC) or C138-109 (VCNE) - Body ground and other terminals Always 10 kΩ or higher
C146-1 (NE+) or C138-62 (NE+) - Body ground and other terminals Always 10 kΩ or higher
C146-2 (NE-) or C138-108 (NE-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (CRANKSHAFT POSITION SENSOR VOLTAGE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK ECM (CRANKSHAFT POSITION SENSOR VOLTAGE)
a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C146)Location & Routing

Click Connector(C146)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Crank Position Sensor

C146-3 (VC) - C146-2 (NE-) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK ECM (CHECK RESISTANCE)

NG

6.REPLACE ECM
4.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the crankshaft position sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C146)Location & Routing

Click Connector(C146)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Crank Position Sensor

C146-3 (VC) - C146-1 (NE+) Ignition switch off No short or no open circuit
C146-1 (NE+) - C146-2 (NE-) Ignition switch off No short or no open circuit



Result:
Proceed to
OK
NG



OK

5.REPLACE CRANKSHAFT POSITION SENSOR

NG

6.REPLACE ECM
5.REPLACE CRANKSHAFT POSITION SENSOR

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 4 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED