Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P03402A  Camshaft Position Sensor "A" Bank 1 or Single Sensor Signal Stuck in Range  P034031  Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal  


DESCRIPTION

The camshaft position sensor (G2 signal) consists of a magnet and MRE (Magneto-Resistive Element).

The G2 signal plate has 3 teeth on its outer circumference and is installed on the intake camshaft sub-assembly RH. When the camshaft rotates, the protrusion on the signal plate and the air gap on the MRE change, causing fluctuations in the magnetic field that generate a voltage in the MRE.

The NE signal plate has 34 teeth and is mounted on the crankshaft angle sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the camshaft angle based on the G2 signal, and detects the crankshaft angle based on the NE signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P03402A Camshaft Position Sensor "A" Bank 1 or Single Sensor Signal Stuck in Range No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more.
(1 trip detection logic)
·

Camshaft position sensor

·

Intake camshaft sub-assembly RH

·

ECM


Comes on SAE Code: P0340
P034031 Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal Camshaft position sensor signal is not input with an engine speed of 650 rpm or more.
(1 trip detection logic)
·

Camshaft position sensor

·

Intake camshaft sub-assembly RH

·

ECM


Comes on SAE Code: P0340

HINT:

If DTC P03402A or P034031 is stored, the following symptoms may appear:

-

Difficulty starting

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P03402A Crank engine for 4 seconds (STA on)
P034031 Idling for 5 second or more (STA off)

WIRING DIAGRAM

A348533E43
1.146,2.021 2.958,2.25 1.813,0.229 10 false Camshaft Position Sensor 1.198,4.073 3.031,4.281 1.833,0.208 10 false Crankshaft Position Sensor 5.146,4.198 5.635,4.49 0.49,0.292 10 false ECM 2.229,0.677 2.427,0.854 0.198,0.177 10 false 3 1.938,0.781 2.229,0.979 0.292,0.198 10 false VC 1.896,3.104 2.25,3.302 0.354,0.198 10 false NE- 2.229,1.052 2.427,1.229 0.198,0.177 10 false 2 2.219,1.427 2.417,1.604 0.198,0.177 10 false 1 2.229,2.646 2.427,2.823 0.198,0.177 10 false 3 2.229,3.021 2.427,3.198 0.198,0.177 10 false 2 2.219,3.385 2.417,3.563 0.198,0.177 10 false 1 5.135,4.021 5.896,4.219 0.76,0.198 10 false C138 1.125,1.854 1.552,2.042 0.427,0.188 10 false C110 1.208,3.896 1.74,4.104 0.531,0.208 10 false C146 4.698,0.792 5.146,1.01 0.448,0.219 10 false VCG 1.844,1.156 2.292,1.354 0.448,0.198 10 false VVI- 4.698,1.177 5.146,1.375 0.448,0.198 10 false G2- 1.802,1.521 2.344,1.719 0.542,0.198 10 false VVI+ 4.698,1.521 5.24,1.719 0.542,0.198 10 false G2+ 1.927,2.76 2.219,2.958 0.292,0.198 10 false VC 4.688,2.76 5.281,2.948 0.594,0.188 10 false VCNE 4.708,3.125 5.063,3.323 0.354,0.198 10 false NE- 1.875,3.469 2.271,3.667 0.396,0.198 10 false NE+ 4.708,3.51 5.104,3.708 0.396,0.198 10 false NE+ 4.448,0.656 4.813,0.875 0.365,0.219 10 false 86 4.438,1.042 4.76,1.24 0.323,0.198 10 false 85 4.438,1.417 4.917,1.698 0.479,0.281 10 false 63 4.385,2.635 4.854,2.906 0.469,0.271 10 false 109 4.438,3.385 4.75,3.573 0.313,0.188 10 false 62 4.365,3 4.802,3.208 0.438,0.208 10 false 108

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.

Result:
Result Proceed to
Cranking is OK. A
Does not crank at all. B




A

2.CHECK ECM (CAMSHAFT POSITION SENSOR VOLTAGE)

B

2.CHECK ECM (CAMSHAFT POSITION SENSOR VOLTAGE)
a.

Disconnect the camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C110)Location & Routing

Click Connector(C110)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor

C110-3 (VC) - C110-2 (VVI-) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (CHECK RESISTANCE)

NG

10.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
3.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the camshaft position sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C110)Location & Routing

Click Connector(C110)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor

C110-3 (VC) - C110-1 (VVI+) Ignition switch off No short or no open circuit
C110-1 (VVI+) - C110-2 (VVI-) Ignition switch off No short or no open circuit



Result:
Proceed to
OK
NG



OK

4.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

11.REPLACE ECM
4.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.
A316078C04
2.469,0.604 2.781,0.76 0.313,0.156 10 false *a 0.448,2.646 0.76,2.844 0.313,0.198 10 false OK 0.479,0.635 0.792,0.833 0.313,0.198 10 false NG
*a Clearance


Check the camshaft position sensor installation.

OK:

Camshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

5.INSPECT INTAKE CAMSHAFT SUB-ASSEMBLY RH (TIMING ROTOR)

NG

9.SECURELY REINSTALL CAMSHAFT POSITION SENSOR
5.INSPECT INTAKE CAMSHAFT SUB-ASSEMBLY RH (TIMING ROTOR)
a.

Inspect the timing rotor of the intake camshaft sub-assembly RH.

OK:

Camshaft timing rotor does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

6.REPLACE CAMSHAFT POSITION SENSOR

NG

8.REPLACE INTAKE CAMSHAFT SUB-ASSEMBLY RH
6.REPLACE CAMSHAFT POSITION SENSOR

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Start the engine and idle it for 5 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

8.REPLACE INTAKE CAMSHAFT SUB-ASSEMBLY RH

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.SECURELY REINSTALL CAMSHAFT POSITION SENSOR

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C110,C138)Location & Routing

Click Connector(C110)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor

Click Connector(C138)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C110-3 (VC) - C138-86 (VCG) Always Below 1 Ω
C110-1 (VVI+) - C138-63 (G2+) Always Below 1 Ω
C110-2 (VVI-) - C138-85 (G2-) Always Below 1 Ω
C110-3 (VC) or C138-86 (VCG) - Body ground and other terminals Always 10 kΩ or higher
C110-1 (VVI+) or C138-63 (G2+) - Body ground and other terminals Always 10 kΩ or higher
C110-2 (VVI-) or C138-85 (G2-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.REPLACE ECM

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED