Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P034011  Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground  P034015  Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P03402A.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P03402A

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P034011 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground Output voltage of camshaft position sensor is less than 0.3 V for 4 seconds or more.
(1 trip detection logic)
·

Camshaft position sensor

·

Open or short in camshaft position sensor circuit

·

ECM


Comes on SAE Code: P0342
P034015 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open Output voltage of camshaft position sensor is higher than 4.7 V for 4 seconds or more.
(1 trip detection logic)
·

Camshaft position sensor

·

Open or short in camshaft position sensor circuit

·

ECM


Comes on SAE Code: P0343

HINT:

If DTC P034011 or P034015 is stored, the following symptoms may appear:

-

Difficulty starting

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




MONITOR DESCRIPTION

When the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P034011
P034015
Ignition switch ON for 4 seconds or more

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

b.

Record any output DTC(s).


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

d.

Turn the ignition switch off and wait for 30 seconds or more.


e.

Disconnect the camshaft position sensor connector.


f.

Turn the ignition switch to ON and wait for 4 seconds or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

h.

Check whether the DTC changes when the connector is disconnected and connected.

Result:
Result Proceed to
DTC does not change A
DTC changes B




A

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

B

5.REPLACE CAMSHAFT POSITION SENSOR
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C110,C138)Location & Routing

Click Connector(C110)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor

Click Connector(C138)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C110-3 (VC) - C138-86 (VCG) Always Below 1 Ω
C110-1 (VVI+) - C138-63 (G2+) Always Below 1 Ω
C110-2 (VVI-) - C138-85 (G2-) Always Below 1 Ω
C110-3 (VC) or C138-86 (VCG) - Body ground and other terminals Always 10 kΩ or higher
C110-1 (VVI+) or C138-63 (G2+) - Body ground and other terminals Always 10 kΩ or higher
C110-2 (VVI-) or C138-85 (G2-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (CAMSHAFT POSITION SENSOR VOLTAGE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK ECM (CAMSHAFT POSITION SENSOR VOLTAGE)
a.

Disconnect the camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C110)Location & Routing

Click Connector(C110)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor

C110-3 (VC) - C110-2 (VVI-) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK ECM (CHECK RESISTANCE)

NG

6.REPLACE ECM
4.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the camshaft position sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C110)Location & Routing

Click Connector(C110)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Cam Position Sensor

C110-3 (VC) - C110-1 (VVI+) Ignition switch off No short or no open circuit
C110-1 (VVI+) - C110-2 (VVI-) Ignition switch off No short or no open circuit



Result:
Proceed to
OK
NG



OK

5.REPLACE CAMSHAFT POSITION SENSOR

NG

6.REPLACE ECM
5.REPLACE CAMSHAFT POSITION SENSOR

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Turn the ignition switch to ON and wait for 4 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED