Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) J

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  Intake/Exhaust System  


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



PROCEDURE

1.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 1)
a.

Start the engine.


b.

Enter the following menus: Powertrain / Engine / Data List / Primary.


c.

Take a snapshot of the Data List items.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.

·

Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.




Result:
Proceed to
NEXT



NEXT

2.READ VALUE USING GTS (MASS AIR FLOW SENSOR AND INTAKE MANIFOLD ABSOLUTE PRESSURE)
2.READ VALUE USING GTS (MASS AIR FLOW SENSOR AND INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor and Intake Manifold Absolute Pressure.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
Intake Manifold Absolute Pressure
50003 372 215,385

b.

Check Intake Manifold Absolute Pressure and Mass Air Flow Sensor in the snapshot taken in procedure 1 when the engine was running at 4000 rpm with no load.

Result:
Result Proceed to
Intake Manifold Absolute Pressure is below 90 kPa*1 A
Mass Air Flow Sensor is 100 gm/sec or more and Intake Manifold Absolute Pressure is 114 kPa or higher*2 B
Except above*3 C


HINT:

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.

Standard atmospheric pressure is 101 kPa (1.0 kgf/cm2, 15 psi). For every 100 m (328 ft.) increase in elevation, pressure drops by 1 kPa (0.01 kgf/cm2, 0.1 psi). This varies by weather.

*1: There may be a problem in the turbocharger system.

*2: There may be a problem in the fuel system or intake system.

*3: There may be a problem in intake system or a problem with the EGR valve (valve stuck open or valve does not close).




A

3.READ VALUE USING GTS (ATMOSPHERIC PRESSURE AND INTAKE MANIFOLD ABSOLUTE PRESSURE)

B

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

C

11.CHECK INTAKE SYSTEM
3.READ VALUE USING GTS (ATMOSPHERIC PRESSURE AND INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Enter the following menus: Powertrain / Engine / Data List / Atmospheric Pressure and Intake Manifold Absolute Pressure.

Powertrain > Engine > Data List
Tester Display
Atmospheric Pressure
Intake Manifold Absolute Pressure
50003 372 229,385

b.

Compare Intake Manifold Absolute Pressure and Atmospheric Pressure when the ignition switch is ON (do not start the engine).

Standard:

Difference between Intake Manifold Absolute Pressure and Atmospheric Pressure is less than 8 kPa.


HINT:
·

If Intake Manifold Absolute Pressure and Atmospheric Pressure have the same value, both are normal. If there is a difference of 10 kPa or higher, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.

·

Standard atmospheric pressure is 101 kPa (1.0 kgf/cm2, 15 psi). For every 100 m (328 ft.) increase in elevation, pressure drops by 1 kPa (0.01 kgf/cm2, 0.1 psi). This varies by weather.



Result:
Result Proceed to
Intake Manifold Absolute Pressure and Atmospheric Pressure have same value A
Intake Manifold Absolute Pressure is different from actual atmospheric pressure B
Atmospheric Pressure is different from actual atmospheric pressure C




A

4.CHECK INTAKE SYSTEM

B

9.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

C

10.REPLACE ECM
4.CHECK INTAKE SYSTEM
a.

Check for air leaks and blockages between the air cleaner case sub-assembly and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.

Result:
Result Proceed to
No leaks or blockages in the intake system A
Leaks and/or blockages exist in the intake system B


HINT:
·

Inspect the intake system, especially hoses and pipes between the air cleaner case sub-assembly and turbocharger sub-assembly.

·

Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.

·

Make sure that the hose between the manifold absolute pressure sensor and intake manifold is not loose or disconnected.

·

Check for any modifications in the intake system made by the user.





A

5.INSPECT TURBOCHARGER SUB-ASSEMBLY

B

8.REPAIR OR REPLACE INTAKE SYSTEM
5.INSPECT TURBOCHARGER SUB-ASSEMBLY
a.

Inspect the turbocharger sub-assembly.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK FOR INTERMITTENT PROBLEMS

NG

7.REPLACE TURBOCHARGER SUB-ASSEMBLY
6.CHECK FOR INTERMITTENT PROBLEMS

Result:
Proceed to
NEXT



NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Replace the turbocharger sub-assembly.

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>TURBOCHARGER>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the malfunctioning part in the intake system.


Result:
Proceed to
NEXT



NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CHECK INTAKE SYSTEM
a.

Check for air leaks and blockages between the air cleaner case sub-assembly and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.

Result:
Result Proceed to
No leaks or blockages in the intake system A
Leaks and/or blockages exist in the intake system B


HINT:
·

Inspect the intake system, especially hoses and pipes between the air cleaner case sub-assembly and turbocharger sub-assembly.

·

Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.

·

Make sure that the hose between the manifold absolute pressure sensor and intake manifold is not loose or disconnected.

·

Check for any modifications in the intake system made by the user.





A

12.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE BANK 1)

B

20.REPAIR OR REPLACE INTAKE SYSTEM
12.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE BANK 1)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


c.

Start the engine and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
50003 372 215

e.

Read the Mass Air Flow Sensor value displayed on the GTS while the engine is idling.


f.

Enter the following menus: Powertrain / Engine / Active Test / Activate the EGR Valve Close Bank 1 / Data List / Mass Air Flow Sensor.

Powertrain > Engine > Active Test
Active Test Display
Activate the EGR Valve Close Bank 1
Data List Display
Mass Air Flow Sensor
50004 372 71 215

g.

Read the Mass Air Flow Sensor value when the EGR valve is closed using the Active Test function.

HINT:
·

Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.

·

When idling the engine, the EGR cooler is bypassed.



Result:
GTS Display Result Proceed to
Activate the EGR Valve Close Bank 1:
OFF to Close
Mass Air Flow Sensor value changes A
Mass Air Flow Sensor value does not change B


NOTICE:

As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.


HINT:

The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter sub-assembly.


Reference:
EGR Valve Condition (Opening) Measuring Condition Mass Air Flow Sensor (Reference)
Open (45%)
·

Atmospheric pressure: 101 kPa

·

Engine coolant temperature: 75°C (167°F)


5 to 14 gm/sec
Closed (0%) 13 to 18 gm/sec




A

13.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR COOLER BYPASS CONTROL VALVE)

B

14.READ VALUE USING GTS (ENGINE SPEED AND MASS AIR FLOW SENSOR)
13.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR COOLER BYPASS CONTROL VALVE)
a.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


b.

Enter the following menus: Powertrain / Engine / Data List / Primary / Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
50003 372 215

c.

Read the Mass Air Flow Sensor value displayed on the GTS while the engine is idling.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the EGR Cooler Bypass Control Valve / Data List / Mass Air Flow Sensor and EGR Cooler Bypass Position.

Powertrain > Engine > Active Test
Active Test Display
Activate the EGR Cooler Bypass Control Valve
Data List Display
Mass Air Flow Sensor
EGR Cooler Bypass Position
50004 372 42025 215,974
HINT:

Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.



e.

Using the Active Test function, switch the EGR cooler bypass valve between "Cooler" and "Bypass" a few times, and then check whether the Mass Air Flow Sensor value changes after switching the valve from "Cooler" to "Bypass".

Result:
GTS Display Result Proceed to
Activate the EGR Cooler Bypass Control Valve:
Cooler to Bypass
Mass Air Flow Sensor value does not change A
Mass Air Flow Sensor value changes B


HINT:

If the EGR cooler is clogged, the mass air flow changes.




A

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

B

17.REPLACE NO.1 EGR COOLER AND NO.2 EGR COOLER
14.READ VALUE USING GTS (ENGINE SPEED AND MASS AIR FLOW SENSOR)
a.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Mass Air Flow Sensor
50003 372 211,215

b.

Start the engine and read the value when 30 seconds have elapsed.

Standard:
Engine Speed Mass Air Flow Sensor
Idling
·

5.5 to 17.3 gm/sec (EGR on)

·

13.5 to 17.3 gm/sec (EGR off)


3000 rpm (without load)
·

38.0 to 124.4 gm/sec (EGR on)

·

81.7 to 124.4 gm/sec (EGR off)





Result:
Proceed to
OK
NG



OK

15.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR COOLER BYPASS CONTROL VALVE)

NG

18.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
15.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR COOLER BYPASS CONTROL VALVE)
a.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


b.

Enter the following menus: Powertrain / Engine / Data List / Primary / Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
50003 372 215

c.

Read the Mass Air Flow Sensor value displayed on the GTS while the engine is idling.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the EGR Cooler Bypass Control Valve / Data List / Mass Air Flow Sensor and EGR Cooler Bypass Position.

Powertrain > Engine > Active Test
Active Test Display
Activate the EGR Cooler Bypass Control Valve
Data List Display
Mass Air Flow Sensor
EGR Cooler Bypass Position
50004 372 42025 215,974
HINT:

Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.



e.

Using the Active Test function, switch the EGR cooler bypass valve between "Cooler" and "Bypass" a few times, and then check whether the Mass Air Flow Sensor value changes after switching the valve from "Cooler" to "Bypass".

Result:
GTS Display Result Proceed to
Activate the EGR Cooler Bypass Control Valve:
Cooler to Bypass
Mass Air Flow Sensor value does not change A
Mass Air Flow Sensor value changes B


HINT:

If the EGR cooler is clogged, the mass air flow changes.




A

16.CHECK FOR DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

B

17.REPLACE NO.1 EGR COOLER AND NO.2 EGR COOLER
16.CHECK FOR DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
a.

Remove the electric EGR control valve assembly.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR COOLER>REMOVAL


b.

Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.

NOTICE:
·

When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.

·

Do not forcibly open the valve, as it may be damaged or deformed.

·

When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.

·

When cleaning the electric EGR control valve assembly, care should be taken to prevent the ingress of cleaning solvent into the bearings of the valve shaft, and when wiping off deposits on the EGR valve, care should be taken not to push the deposits into the bearings of the valve shaft. These contaminants may adversely affect the function of the EGR valve.

·

When cleaning the electric EGR control valve assembly, perform the initialization procedure.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION



HINT:
·

If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.

·

If the EGR valve does not close properly or is stuck open, the amount of recirculated exhaust gas becomes excessive and combustion becomes unstable. Also, there may be a lack of power.




Result:
Proceed to
NEXT



NEXT

17.REPLACE NO.1 EGR COOLER AND NO.2 EGR COOLER
17.REPLACE NO.1 EGR COOLER AND NO.2 EGR COOLER
a.

Replace the No. 1 EGR cooler and No. 2 EGR cooler.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EGR COOLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
18.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END

20.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the malfunctioning part in the intake system.


Result:
Proceed to
NEXT



NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED