Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P048014  Fan 1 Control Circuit Low Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P048012.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P048012

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P048014 Fan 1 Control Circuit Low Circuit Short to Ground or Open Open or short in fan control solenoid circuit (1 trip detection logic).
·

Open or short in fan control solenoid circuit

·

Fan control solenoid (fluid coupling assembly)

·

ECM


Does not come on SAE Code: P0691

MONITOR DESCRIPTION

The ECM monitors the output voltage while the fan control solenoid is operating.

The fan control solenoid turns on and off according to ON/OFF switching of a transistor inside the ECM.

If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the fan control solenoid circuit and stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P048014 Start the engine and wait for at 2 minutes or more.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY)

OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY))

NG

REPLACE FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY))
a.

Disconnect the fan control solenoid (fluid coupling assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(C165)Location & Routing

Click Connector(C165)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Fluid Coupling Assembly

C165-1 (EFC+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 1 RELAY - AIR BY-PASS VALVE ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (FAN CONTROL SOLENOID (FLUID COUPLING ASSEMBLY) - ECM)
a.

Disconnect the fan control solenoid (fluid coupling assembly) connector.


b.

Disconnect the ECM connector.




OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


b.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P048014)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P048014)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P048014 is output B




A

B