Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P12B073  Exhaust Control Valve Actuator Stuck Closed  


DESCRIPTION

Refer to DTC P12AC12.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P12AC12

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P12B073 Exhaust Control Valve Actuator Stuck Closed When switching from single turbo to twin turbo, a difference between atmospheric pressure and 2nd compressor outlet pressure of 12 kPa or less continues for 3.0147 seconds or more.
(1 trip detection logic)
·

No. 1 vacuum switching valve assembly (for exhaust control valve)

·

Actuator assembly (for exhaust control valve)

·

Exhaust control valve (No. 2 turbocharger sub-assembly)

·

Atmospheric pressure sensor (ECM)

·

Manifold absolute pressure sensor (2nd turbocharger outlet side)


Comes on SAE Code: P12B0

Related Data List
DTC No. Data List
P12B073
·

Atmospheric Pressure

·

Intake Manifold Absolute Pressure

·

2nd Turbocharger/Supercharger Outlet Pressure

·

Exhaust Control Valve Current-Carrying Request



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P12B073 Activate the 2 Stage VN Turbo (Active Test)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS (DTC P12B073)
a.

Check the DTC judgment result.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P12B073 is output A
DTC P12B073 and other DTCs are output* B


HINT:

*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.




A

2.CHECK INTAKE / EXHAUST SYSTEM

B

GO TO DTC CHART

2.CHECK INTAKE / EXHAUST SYSTEM
a.

Check that there are no malfunctions in intake/exhaust system piping such as damage, air suction or exhaust leaks in the engine room.


Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)

NG

9.REPAIR OR REPLACE INTAKE / EXHAUST SYSTEM
3.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)
a.

Using the table, read the normal atmospheric pressure value for the applicable altitude and temperature.

A479641C01
0.177,0.063 0.49,0.26 0.313,0.198 10 false *a 0.396,0.51 0.708,0.708 0.313,0.198 10 false *b 2.719,0.51 3.031,0.708 0.313,0.198 10 false *b 5.031,0.51 5.344,0.708 0.313,0.198 10 false *b 1.146,0.51 1.458,0.708 0.313,0.198 10 false *c 3.438,0.5 3.75,0.698 0.313,0.198 10 false *c 5.729,0.5 6.042,0.698 0.313,0.198 10 false *c 1.802,0.5 2.115,0.698 0.313,0.198 10 false *d 4.125,0.51 4.438,0.708 0.313,0.198 10 false *d 6.396,0.521 6.708,0.719 0.313,0.198 10 false *d
*a Altitude, Temperature and Atmospheric Pressure Correlation Table *b Altitude (m (ft.))
*c Temperature (°C (°F)) *d Atmospheric Pressure (kPa (psi))


HINT:
·

Standard atmospheric pressure is approximately 101 kPa(abs) [14.65 psi(abs)].

·

For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa [0.15 psi]. This varies by weather.




b.

Compare the Atmospheric pressure value in the Data List with the normal atmospheric value from the table.

Powertrain > Engine > Data List
Tester Display
Atmospheric Pressure
50003 372 229

Result:
Result Proceed to
Difference between Atmospheric Pressure in the Data List and normal atmospheric pressure value is 10 kPa (1.45 psi) or more. A
Except above B



A

B

4.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (2ND TURBOCHARGER OUTLET SIDE)
4.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (2ND TURBOCHARGER OUTLET SIDE)
a.

Check the manifold absolute pressure sensor (2nd turbocharger outlet side).

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EXHAUST CONTROL VALVE)

NG

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR (2ND TURBOCHARGER OUTLET SIDE)

5.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EXHAUST CONTROL VALVE)
a.

Remove the vacuum hose connected to the vacuum pump and install the vacuum pump to the vacuum hose.


b.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Exhaust Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the Exhaust Control Valve
50004 372 42041

c.

Perform the Active Test.


d.

Check that the actuator assembly link of the exhaust control valve operates when negative pressure is applied using the vacuum pump.

OK:

The actuator assembly link of the exhaust control valve operates.



Result:
Proceed to
OK
NG



OK

6.INSPECT VACUUM PUMP ASSEMBLY

NG

10.INSPECT NO.1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EXHAUST CONTROL VALVE)
6.INSPECT VACUUM PUMP ASSEMBLY
a.

Inspect the vacuum pump assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM PUMP>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

REPLACE VACUUM PUMP ASSEMBLY

7.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS
8.CHECK WHETHER DTC OUTPUT RECURS
a.

Enter the following menus: Powertrain / Engine / Active Test / Activate the 2 Stage VN Turbo.

Powertrain > Engine > Active Test
Tester Display
Activate the 2 Stage VN Turbo
50004 372 42038

b.

Perform the Active Test for 30 seconds or more.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

Result:
Result Proceed to
P12B073 is output A
DTCs are not output B




A

REPLACE NO.2 TURBOCHARGER SUB-ASSEMBLY

B

END

9.REPAIR OR REPLACE INTAKE / EXHAUST SYSTEM
a.

Repair or replace the malfunctioning part in the intake/exhaust system.


Result:
Proceed to
NEXT



NEXT

3.READ VALUE USING GTS (ATMOSPHERIC PRESSURE)
10.INSPECT NO.1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EXHAUST CONTROL VALVE)
a.

Inspect the No. 1 vacuum switching valve assembly (for exhaust control valve).

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>VACUUM SWITCHING VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK VACUUM HOSE CONNECTIONS

NG

REPLACE NO.1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EXHAUST CONTROL VALVE)

11.CHECK VACUUM HOSE CONNECTIONS
a.

Check the vacuum hose connections.

OK:

Vacuum hose is connected correctly and is not damaged.



Result:
Proceed to
OK
NG



OK

12.INSPECT NO.2 TURBOCHARGER SUB-ASSEMBLY (FOR EXHAUST CONTROL VALVE)

NG

CONNECT HOSE CORRECTLY

12.INSPECT NO.2 TURBOCHARGER SUB-ASSEMBLY (FOR EXHAUST CONTROL VALVE)
a.

Remove the vacuum hose from the actuator assembly (for exhaust control valve) of the No. 2 turbocharger sub-assembly.


b.

Connect the vacuum pump to the exhaust control valve actuator.


c.

Check that the exhaust control valve operates smoothly when negative pressure is applied.

OK:

The link on the exhaust control valve actuator operates.



Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

13.INSPECT ACTUATOR ASSEMBLY (FOR EXHAUST CONTROL VALVE)
13.INSPECT ACTUATOR ASSEMBLY (FOR EXHAUST CONTROL VALVE)
a.

Remove the compressor housing installation bolt from the No. 2 turbocharger sub-assembly, and remove the E-ring from the link on the exhaust control valve actuator.


b.

Disconnect the link on the exhaust control valve actuator.


c.

Connect the vacuum pump to the exhaust control valve actuator.


d.

Check that the exhaust control valve actuator rod operates smoothly when negative pressure is applied.

OK:

The exhaust control valve actuator rod operates smoothly.



Result:
Proceed to
OK
NG



OK

REPLACE NO.2 TURBOCHARGER SUB-ASSEMBLY

NG

REPLACE ACTUATOR ASSEMBLY (FOR EXHAUST CONTROL VALVE)