Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P2CD573  Turbocharger/Supercharger Bypass Valve "C" Stuck Actuator Stuck Closed  


DESCRIPTION

Refer to DTC P25F812.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P25F812

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P2CD573 Turbocharger/Supercharger Bypass Valve "C" Stuck Actuator Stuck Closed During twin turbo operation, a pressure difference before and after the intake air control valve is 50 kPa or higher and continues for 5.5 seconds or more.
(1 trip detection logic)
·

No. 2 vacuum switching valve assembly (for intake air control valve)

·

Intake air control valve

·

Manifold absolute pressure sensor (2nd turbocharger outlet side)


Comes on SAE Code: P2CD5

Related Data List
DTC No. Data List
P2CD573
·

1st Turbocharger/Supercharger Outlet Pressure (Control Value)

·

2nd Turbocharger/Supercharger Outlet Pressure (Control Value)

·

Air Control Valve Current-Carrying Request



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2CD573 Activate the 2 Stage VN Turbo (Active Test)

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P2CD573 is output A
DTC P2CD573 and other DTCs are output B


HINT:

If codes other than DTC P2CD573 is output, perform troubleshooting for those DTCs first.




A

2.CHECK INTAKE / EXHAUST SYSTEM

B

GO TO DTC CHART

2.CHECK INTAKE / EXHAUST SYSTEM
a.

Check that there are no malfunctions in intake/exhaust system piping such as damage, air suction or exhaust leaks in the engine room.


Result:
Proceed to
OK
NG



OK

3.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

12.REPAIR OR REPLACE INTAKE / EXHAUST SYSTEM
3.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR

Result:
Proceed to
OK
NG



OK

4.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (2ND TURBOCHARGER OUTLET SIDE)

NG

4.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (2ND TURBOCHARGER OUTLET SIDE)
a.

Check the manifold absolute pressure sensor (2nd turbocharger outlet side).

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

5.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR CONTROL VALVE)

NG

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR (2ND TURBOCHARGER OUTLET SIDE)

5.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR CONTROL VALVE)
a.

Remove the vacuum hose connected to the vacuum pump and install the vacuum pump to the vacuum hose.


b.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Air Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the Air Control Valve
50004 372 42040

c.

Perform the Active Test.


d.

Check that the link on the intake air control valve actuator operates when negative pressure is applied using the vacuum pump.

OK:

The link on the intake air control valve actuator operates.



Result:
Proceed to
OK
NG



OK

6.INSPECT VACUUM PUMP ASSEMBLY

NG

9.INSPECT NO.2 VACUUM SWITCHING VALVE ASSEMBLY (FOR INTAKE AIR CONTROL VALVE)
6.INSPECT VACUUM PUMP ASSEMBLY
a.

Inspect the vacuum pump assembly.

Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM PUMP>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

REPLACE VACUUM PUMP ASSEMBLY

7.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

8.CHECK OTHER DTC OUTPUT
8.CHECK OTHER DTC OUTPUT
a.

Enter the following menus: Powertrain / Engine / Active Test / Activate the 2 Stage VN Turbo.

Powertrain > Engine > Active Test
Tester Display
Activate the 2 Stage VN Turbo
50004 372 42038

b.

Perform the Active Test for 30 seconds or more.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

Result:
Result Proceed to
DTC P2CD573 is output A
DTCs are not output B




A

B

END

9.INSPECT NO.2 VACUUM SWITCHING VALVE ASSEMBLY (FOR INTAKE AIR CONTROL VALVE)
a.

Inspect the No. 2 vacuum switching valve assembly (for intake air control valve).

Click hereEngine / Hybrid System>F33A-FTV (INTAKE / EXHAUST)>VACUUM SWITCHING VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK VACUUM HOSE CONNECTIONS

NG

REPLACE NO.2 VACUUM SWITCHING VALVE ASSEMBLY (FOR INTAKE AIR CONTROL VALVE)

10.CHECK VACUUM HOSE CONNECTIONS
a.

Check the vacuum hose connections.

OK:

Vacuum hose is connected correctly and is not damaged.



Result:
Proceed to
OK
NG



OK

11.INSPECT INTAKE AIR CONTROL VALVE ASSEMBLY

NG

CONNECT HOSE CORRECTLY

11.INSPECT INTAKE AIR CONTROL VALVE ASSEMBLY
a.

Remove the vacuum hose from the intake air control value actuator.


b.

Connect the vacuum pump to the intake air control valve actuator.


c.

Check that the intake air control valve operates smoothly when negative pressure is applied.

OK:

The intake air control valve operates smoothly.



Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

12.REPAIR OR REPLACE INTAKE / EXHAUST SYSTEM
a.

Repair or replace the malfunctioning part in the intake/exhaust system.


Result:
Proceed to
NEXT



NEXT

3.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR