Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P268712  Fuel Supply Heater Control Circuit High Circuit Short to Battery  P268714  Fuel Supply Heater Control Circuit Low Circuit Short to Ground or Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P268712 Fuel Supply Heater Control Circuit High Circuit Short to Battery When the PTC heater (fuel filter heater) is operating, there is an open circuit or short in the FUEL FIL relay drive circuit for 3 seconds or more.
(1 trip detection logic)
·

Open or short in FUEL FIL relay circuit

·

FUEL FIL relay

·

ECM


Does not come on SAE Code: P2689
P268714 Fuel Supply Heater Control Circuit Low Circuit Short to Ground or Open When the PTC heater (fuel filter heater) is not operating, there is an open circuit or short in the FUEL FIL relay drive circuit for 3 seconds or more.
(1 trip detection logic)
·

Open or short in FUEL FIL relay circuit

·

FUEL FIL relay

·

ECM


Does not come on SAE Code: P2688

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P268712
P268714
Perform the Active Test "Activate the Fuel Filter Heater"

WIRING DIAGRAM

A492048E01
6.208,4.427 6.688,5.094 0.479,0.667 10 false ECM 6.198,4.271 6.656,4.469 0.458,0.198 10 false B70 5.635,3.635 5.792,3.833 0.156,0.198 10 false 3 5.573,1.969 5.885,2.177 0.313,0.208 10 false 35 5.573,1.208 5.885,1.417 0.313,0.208 10 false 16 5.865,1.198 6.323,1.396 0.458,0.198 10 false FLH 5.865,2.104 6.323,2.302 0.458,0.198 10 false +B2 5.865,3.813 6.323,4.01 0.458,0.198 10 false MREL 2.427,3.917 3.656,4.115 1.229,0.198 10 false EFI NO. 2 2.813,1.229 2.969,1.427 0.156,0.198 10 false 2 2.094,1.25 2.25,1.448 0.156,0.198 10 false 3 1.313,1.26 1.469,1.458 0.156,0.198 10 false 5 0.99,1.26 1.146,1.458 0.156,0.198 10 false 2 0.604,1.25 0.76,1.448 0.156,0.198 10 false 1 0.604,1.521 1.281,1.979 0.677,0.458 10 false EFI MAIN NO. 2 1.313,2.458 2.583,2.813 1.271,0.354 10 false EFI MAIN NO. 2 1.313,1.99 1.469,2.188 0.156,0.198 10 false 2 2.094,2 2.25,2.198 0.156,0.198 10 false 1 2.438,1.969 2.594,2.167 0.156,0.198 10 false 2 2.844,1.979 3,2.177 0.156,0.198 10 false 1 4.563,1.969 4.719,2.167 0.156,0.198 10 false 1 4.906,1.969 5.063,2.167 0.156,0.198 10 false 2 4.458,2.271 5.688,2.469 1.229,0.198 10 false EFI-B NO. 2 2.344,2.25 3.573,2.448 1.229,0.198 10 false EFI-B NO. 3 3.313,4.104 4.625,4.427 1.313,0.323 10 false EFI MAIN NO. 1 2.417,1.229 2.573,1.427 0.156,0.198 10 false 1 2.396,1.542 3.156,1.844 0.76,0.302 10 false EFI NO. 3 0.417,3.313 1.458,3.656 1.042,0.344 10 false R/B NO. 2 2.823,3.625 2.979,3.823 0.156,0.198 10 false 2 2.406,3.625 2.563,3.823 0.156,0.198 10 false 1 0.594,4.792 1.208,4.99 0.615,0.198 10 false Battery 4.229,0.74 5.458,1.146 1.229,0.406 10 false V15 3.469,1.604 4.51,1.948 1.042,0.344 10 false FUEL FIL 1.49,0.521 2.531,0.865 1.042,0.344 10 false FUEL FIL 4.344,0.385 4.656,0.583 0.313,0.198 10 false H+ 5.063,0.385 5.375,0.583 0.313,0.198 10 false H- 4.052,0.271 4.208,0.469 0.156,0.198 10 false 5 4.177,0.26 4.333,0.458 0.156,0.198 10 false 1 5.313,0.26 5.469,0.458 0.156,0.198 10 false 2 3.292,1.208 3.448,1.406 0.156,0.198 10 false 1 4.073,1.208 4.229,1.406 0.156,0.198 10 false 2 3.292,0.24 3.448,0.438 0.156,0.198 10 false 3 1.156,3.313 2.198,3.656 1.042,0.344 10 false EFI MAIN NO. 1 1.938,2.979 2.094,3.177 0.156,0.198 10 false 2 1.51,2.979 1.667,3.177 0.156,0.198 10 false 1 0.458,4.125 1.5,4.469 1.042,0.344 10 false SUB R/B NO. 1 1.896,0.26 2.052,0.458 0.156,0.198 10 false 2 1.531,0.25 1.688,0.448 0.156,0.198 10 false 1 4.25,0.896 5.333,1.375 1.083,0.479 10 false Diesel Fuel Filter Assembly 4.104,3.656 4.26,3.854 0.156,0.198 10 false 1 3.26,3.646 3.417,3.844 0.156,0.198 10 false 2 3.281,3.031 3.438,3.229 0.156,0.198 10 false 3 4.094,3.021 4.25,3.219 0.156,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUEL FIL RELAY

OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL FIL RELAY)

NG

REPLACE FUEL FIL RELAY

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL FIL RELAY)
a.
A499132C02
0.115,0.063 0.427,0.26 0.313,0.198 10 false *1 0.177,1.792 0.49,1.99 0.313,0.198 10 false *2
*1 No. 4 Engine Room Relay Block and Junction Block Assembly
*2 FUEL FIL Relay


Remove the FUEL FIL relay from the No. 4 engine room relay block and junction block assembly.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
FUEL FIL relay terminal 1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FUEL FIL RELAY - ECM)

NG

6.INSPECT EFI MAIN NO. 2 RELAY
3.CHECK HARNESS AND CONNECTOR (FUEL FIL RELAY - ECM)
a.

Remove the FUEL FIL relay from the No. 4 engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B70)Location & Routing

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

FUEL FIL relay terminal 2 - B70-16 (FLH) Always Below 1 Ω
FUEL FIL relay terminal 2 or B70-16 (FLH) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Perform the Active Test.

Powertrain > Engine > Active Test
Tester Display
Activate the Fuel Filter Heater
50004 372 42042

d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

If no pending DTC is output, the repair has been successfully completed.


Result:
Proceed to
NEXT



NEXT

END

6.INSPECT EFI MAIN NO. 2 RELAY

OK

7.CHECK HARNESS AND CONNECTOR (FUEL FIL RELAY - EFI MAIN NO. 2 RELAY)

NG

REPLACE EFI MAIN NO. 2 RELAY

7.CHECK HARNESS AND CONNECTOR (FUEL FIL RELAY - EFI MAIN NO. 2 RELAY)
a.

Remove the FUEL FIL relay and EFI MAIN NO. 2 relay from the No. 4 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FUEL FIL relay terminal 1 - EFI MAIN NO. 2 relay terminal 3 Always Below 1 Ω
FUEL FIL relay terminal 1 or EFI MAIN NO. 2 relay terminal 3 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI MAIN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI MAIN NO. 2 RELAY)
a.

Remove the EFI MAIN NO. 2 relay from the No. 4 engine room relay block and junction block assembly.


b.
A496914C02
0.115,0.063 0.427,0.26 0.313,0.198 10 false *1 2.333,0.333 2.646,0.531 0.313,0.198 10 false *2
*1 No. 4 Engine Room Relay Block and Junction Block Assembly
*2 EFI MAIN NO. 2 Relay


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
EFI MAIN NO. 2 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI MAIN NO. 2 relay from the No. 4 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN NO. 2 relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 2 RELAY - EFI MAIN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 2 RELAY - EFI MAIN NO. 1 RELAY)
a.

Remove the EFI MAIN NO. 2 relay from the No. 4 engine room relay block and junction block assembly.


b.

Remove the EFI MAIN NO. 1 relay from the No. 3 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN NO. 2 relay terminal 1 - EFI MAIN NO. 1 relay terminal 5 Always Below 1 Ω
EFI MAIN NO. 2 relay terminal 1 or EFI MAIN NO. 1 relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR