The engine stop and start ECU detects malfunctions by comparing the conditions of the shift position signal and NSW signal. If a malfunction is detected, the engine stop and start ECU blinks the stop and start cancel indicator, prohibits stop and start control and stores DTC P085012 or P085014.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Note |
|---|---|---|---|---|---|
| P085012 | Park/Neutral Switch Circuit Short to Battery | Both of the following conditions are met for 15 seconds or more (2 trip detection logic):
·
Ignition switch ON
·
NSW signal is off with the shift lever in P or N |
·
Park/neutral position switch assembly
·
Engine stop and start ECU
·
ECM
·
TCM
·
Wire harness or connector |
Blinks | SAE Code: P0852 |
| P085014 | Park/Neutral Switch Circuit Short to Ground or Open | Both of the following conditions are met for 2 seconds or more (2 trip detection logic):
·
Ignition switch ON
·
NSW signal is on with the shift lever in P or N |
·
Park/neutral position switch assembly
·
Engine stop and start ECU
·
ECM
·
TCM
·
Wire harness or connector |
Blinks | SAE Code: P0851 |
Before replacing the engine stop and start ECU, read the number of starter operations, total number of engine starts and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
When the ECM is replaced on a vehicle with a non-specified battery, it is necessary to perform battery type switching.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
Before replacing the ECM, refer to Service Bulletin (for Immobiliser System).
Perform Registration (VIN registration or frame number registration) after replacing the ECM.
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION
After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Enter the following menus: Powertrain / Transmission / Data List / Shift SW Status (P, R, N, D Range).
In accordance with the display on the GTS, read the Data List.
| Tester Display |
|---|
| Shift SW Status (P Range) |
| Shift SW Status (R Range) |
| Shift SW Status (N Range) |
| Shift SW Status (D Range) |
| Tester Display | Measurement Item | Range | Normal Condition |
|---|---|---|---|
| Shift SW Status (P Range) | Park/Neutral position switch assembly status | OFF or ON | OFF: Shift lever not in P ON: Shift lever in P |
| Shift SW Status (R Range) | Park/Neutral position switch assembly status | OFF or ON | OFF: Shift lever not in R ON: Shift lever in R |
| Shift SW Status (N Range) | Park/Neutral position switch assembly status | OFF or ON | OFF: Shift lever not in N ON: Shift lever in N |
| Shift SW Status (D Range) | Park/Neutral position switch assembly status | OFF or ON | OFF: Shift lever not in D ON: Shift lever in D |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus: Powertrain / Engine / Data List / Neutral Position SW.
| Tester Display |
|---|
| Neutral Position SW |
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition |
|---|---|---|---|
| Neutral Position SW | Park/neutral position switch assembly status | OFF or ON | OFF: Shift lever not in P or N ON: Shift lever in P or N |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Inspect the park/neutral position switch assembly.
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Disconnect the engine stop and start ECU connector.
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B38,C34)Location & Routingewd_type=routing;type=c,c;code=B38,C34 Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B38;pinno=21,17 |
||
| B38-21 (STA) - C34-5 (L) | Always | Below 1 Ω |
| B38-17 (CLL) - C34-4 (B) | Always | Below 1 Ω |
| B38-21 (STA) - Body ground | Always | 80 to 180 Ω |
| B38-17 (CLL) - Body ground | Always | 10 kΩ or higher |
| C34-5 (L) - Body ground | Always | 80 to 180 Ω |
| C34-4 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the park/neutral position switch assembly.
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Disconnect the ECM connectors.
Disconnect the TCM connectors.
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: for V35A-FTS *2: for F33A-FTV |
||
Click Location & Routing(C36,C34,C37,B70)Location & Routingewd_type=routing;type=c,c,c,c;code=C36,C34,C37,B70 |
||
| C36-15 (P) - C34-6 (PL) | Always | Below 1 Ω |
| C36-34 (R) - C34-1 (RL) | Always | Below 1 Ω |
| C36-16 (N) - C34-9 (NL) | Always | Below 1 Ω |
| C36-35 (D) - C34-7 (DL) | Always | Below 1 Ω |
| C37-7 (NSW) - C34-4 (B)*1 | Always | Below 1 Ω |
| B70-30 (NSW) - C34-4 (B)*2 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
NEXT
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine.
Perform a road test.
Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P080512 or P085014 is output | A |
| DTC P085012 or P085014 is not output | B |
A
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
B