Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2021.07–2022.11
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467519 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 2 Line (for RHD)  


DESCRIPTION

Symptom Trouble Area
There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that store a communication stop history on the "Detail" screen.
·

CAN main bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

TCM

·

ECM

·

No. 7 global CAN junction connector



WIRING DIAGRAM

C464938E02
5.156,1.521 7.104,1.927 1.948,0.406 10 false Central Gateway ECU (Network Gateway ECU) 0.719,1.667 2.667,2.073 1.948,0.406 10 false TCM 6.281,3.542 6.792,3.823 0.51,0.281 10 false ECM 2.813,3.594 4.458,4.031 1.646,0.438 10 false No. 7 Global CAN Junction Connector 5.146,1.375 5.646,1.594 0.5,0.219 10 false I42 6.177,0.552 6.677,0.771 0.5,0.219 10 false CA4H 6.177,1.229 6.677,1.448 0.5,0.219 10 false CA4L 6.198,2.542 6.698,2.76 0.5,0.219 10 false CANH 5.698,0.542 6,0.781 0.302,0.24 10 false 26 5.698,1.031 6,1.271 0.302,0.24 10 false 25 6.208,3.281 6.708,3.5 0.5,0.219 10 false CANL 0.906,0.646 1.406,0.865 0.5,0.219 10 false CANH 0.917,1.115 1.417,1.333 0.5,0.219 10 false CANL 1.396,1.021 1.698,1.26 0.302,0.24 10 false 21 1.417,0.5 1.719,0.74 0.302,0.24 10 false 20 2.802,3.427 3.302,3.646 0.5,0.219 10 false I118 0.74,1.5 1.24,1.719 0.5,0.219 10 false C36 3.24,0.531 3.542,0.771 0.302,0.24 10 false 4 3.177,1.031 3.479,1.271 0.302,0.24 10 false 15 4.042,1.021 4.344,1.26 0.302,0.24 10 false 12 4.063,0.51 4.365,0.75 0.302,0.24 10 false 1 4.031,3.094 4.333,3.333 0.302,0.24 10 false 13 4.052,2.51 4.354,2.75 0.302,0.24 10 false 2 5.219,2.406 5.521,2.646 0.302,0.24 10 false 18 5.24,2.99 5.542,3.229 0.302,0.24 10 false 17 5.698,2.99 5.833,3.188 0.135,0.198 10 false 8 5.677,2.406 5.833,2.594 0.156,0.188 10 false 7 5.656,3.417 5.969,3.615 0.313,0.198 10 false *2 5.24,3.427 5.552,3.625 0.313,0.198 10 false *1 5.24,2.833 5.552,3.031 0.313,0.198 10 false *1 5.646,2.833 5.958,3.031 0.313,0.198 10 false *2 5.25,2.615 5.563,2.813 0.313,0.198 10 false B1 5.25,3.198 5.563,3.396 0.313,0.198 10 false B1 5.604,2.615 5.917,2.813 0.313,0.198 10 false B70 5.615,3.188 5.927,3.385 0.313,0.198 10 false B70 0.26,3.646 2.708,3.844 2.448,0.198 10 false *1: for V35A-FTS 0.26,4.167 2.708,4.365 2.448,0.198 10 false *2: for F33A-FTV

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE
NOTICE:

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the ignition switch, any other switches or door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C458715C01
1.51,0.073 1.927,0.323 0.417,0.25 2.167,1.938 2.01,1.938 2.01,1.938 2.01,0.906 true 2.74,1.74 2.583,1.74 2.583,1.74 2.115,0.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.104 1.875,0.26 0.24,0.156 10 false I42 2.208,1.833 2.604,2.021 0.396,0.188 10 false CA4H 2.781,1.625 3.156,1.823 0.375,0.198 10 false CA4L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-26 (CA4H) - I42-25 (CA4L) Cable disconnected from negative (-) battery terminal Below 70 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS WIRES

NG

35.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
2.CHECK FOR SHORT IN CAN BUS WIRES
a.
C458715C01
1.51,0.073 1.927,0.323 0.417,0.25 2.167,1.938 2.01,1.938 2.01,1.938 2.01,0.906 true 2.74,1.74 2.583,1.74 2.583,1.74 2.115,0.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.104 1.875,0.26 0.24,0.156 10 false I42 2.208,1.833 2.604,2.021 0.396,0.188 10 false CA4H 2.781,1.625 3.156,1.823 0.375,0.198 10 false CA4L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-26 (CA4H) - I42-25 (CA4L) Cable disconnected from negative (-) battery terminal 54 Ω or higher



Result:
Proceed to
OK
NG



OK

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE

NG

25.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE
a.
C458715C01
1.51,0.073 1.927,0.323 0.417,0.25 2.167,1.938 2.01,1.938 2.01,1.938 2.01,0.906 true 2.74,1.74 2.583,1.74 2.583,1.74 2.115,0.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.104 1.875,0.26 0.24,0.156 10 false I42 2.208,1.833 2.604,2.021 0.396,0.188 10 false CA4H 2.781,1.625 3.156,1.823 0.375,0.198 10 false CA4L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42,I76)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I42-26 (CA4H) - I76-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-25 (CA4L) - I76-16 (BAT)



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE

NG

15.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
4.CHECK FOR SHORT TO GND IN CAN BUS WIRE
a.
C458715C01
1.51,0.073 1.927,0.323 0.417,0.25 2.167,1.938 2.01,1.938 2.01,1.938 2.01,0.906 true 2.74,1.74 2.583,1.74 2.583,1.74 2.115,0.896 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.635,0.104 1.875,0.26 0.24,0.156 10 false I42 2.208,1.833 2.604,2.021 0.396,0.188 10 false CA4H 2.781,1.625 3.156,1.823 0.375,0.198 10 false CA4L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42,I76)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

Click Connector(I76)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Data Link Connector 3

I42-26 (CA4H) - I76-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-25 (CA4L) - I76-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the I118 No. 7 global CAN junction connector.



Result:
Proceed to
OK
NG



OK

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)

NG

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)

OK

7.CHECK VEHICLE TYPE

NG

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)
7.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for V35A-FTS A
except V35A-FTS B



A

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

9.CHECK VEHICLE TYPE
8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

OK

9.CHECK VEHICLE TYPE

NG

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
9.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for F35A-FTV A
except F33A-FTV B



A

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

OK

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

NG

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Disconnect the C36 TCM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the B1 ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the B70 ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

15.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the I118 No. 7 global CAN junction connector.



Result:
Proceed to
OK
NG



OK

16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)

NG

21.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)

OK

17.CHECK VEHICLE TYPE

NG

22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)
17.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for V35A-FTS A
except V35A-FTS B



A

18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

19.CHECK VEHICLE TYPE
18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

OK

19.CHECK VEHICLE TYPE

NG

23.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
19.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for F33A-FTV A
except F33A-FTV B



A

20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

OK

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

NG

24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
21.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Disconnect the C36 TCM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)

23.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the B1 ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the B70 ECM connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

25.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the I118 No. 7 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-1 (CANH) - I118-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)

NG

31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-4 (CANH) - I118-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

27.CHECK VEHICLE TYPE

NG

32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)
27.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for V35A-FTS A
except V35A-FTS B



A

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

29.CHECK VEHICLE TYPE
28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-2 (CANH) - I118-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

29.CHECK VEHICLE TYPE

NG

33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
29.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for F33A-FTV A
except F33A-FTV B



A

30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-2 (CANH) - I118-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

NG

34.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
31.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-1 (CANH) - I118-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - TCM)
a.

Disconnect the C36 TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-4 (CANH) - I118-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR- TCM)

33.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the B1 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-2 (CANH) - I118-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

34.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the B70 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-2 (CANH) - I118-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

35.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the I118 No. 7 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-1 (CANH) - I118-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

36.CHECK VEHICLE TYPE

NG

40.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
36.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for V35A-FTS A
except V35A-FTS B



A

37.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

38.CHECK VEHICLE TYPE
37.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-2 (CANH) - I118-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

38.CHECK VEHICLE TYPE

NG

41.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
38.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for F33A-FTV A
except F33A-FTV B



A

39.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)

B

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

39.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 GLOBAL CAN JUNCTION CONNECTOR - ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I118)Location & Routing

Click Connector(I118)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>No. 7 Global CAN Junction Connector

I118-2 (CANH) - I118-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 7 GLOBAL CAN JUNCTION CONNECTOR

NG

42.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
40.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the I118 No. 7 global CAN junction connector.


b.

Disconnect the I42 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I42)Location & Routing

Click Connector(I42)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Network Gateway ECU

I42-26 (CA4H) - I42-25 (CA4L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)

41.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the I118 No. 7 global CAN junction connector.


b.

Disconnect the B1 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B1-18 (CANH) - B1-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (ECM - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)

42.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)
a.

Reconnect the I118 No. 7 global CAN junction connector.


b.

Disconnect the B70 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B70)Location & Routing

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B70-7 (CANH) - B70-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (ECM - NO. 7 GLOBAL CAN JUNCTION CONNECTOR)