Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV) › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0488019 AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV)  P170300  AT Solenoid Output Malfunction  


DESCRIPTION

The TCM detects an erroneous downshift output to the automatic transmission or a gear shifting malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P170300 AT Solenoid Output Malfunction ECU malfunction (1 trip detection logic)
·

Wire harness or connector

·

Transmission revolution sensor (SP2)

·

Transmission wire

·

Solenoid (SL1) valve

·

Solenoid (SL2) valve

·

Solenoid (SL3) valve

·

Solenoid (SL4) valve

·

Solenoid (SL5) valve

·

Solenoid (SL6) valve

·

Solenoid (SC1) valve

·

Solenoid (SL) valve

·

Solenoid (SR) valve

·

Solenoid (SLU) valve

·

TCM


Comes on DTC stored SAE: P1703

MONITOR DESCRIPTION

When an erroneous downshift is output or a gear shifting malfunction is detected while downshifting or changing gears while driving, the TCM stores a DTC.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P170300.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

C458224E02
1.323,0.625 1.938,0.823 0.615,0.198 10 false SL1+ 2.458,0.625 3.073,0.823 0.615,0.198 10 false SL1+ 1.323,1.573 1.938,1.771 0.615,0.198 10 false SL1- 2.448,1.573 3.063,1.771 0.615,0.198 10 false SL1- 5.563,1.573 6.177,1.771 0.615,0.198 10 false SL2- 4.417,1.573 5.031,1.771 0.615,0.198 10 false SL2- 4.417,0.625 5.031,0.823 0.615,0.198 10 false SL2+ 5.542,0.625 6.156,0.823 0.615,0.198 10 false SL2+ 1.323,2.698 1.938,2.896 0.615,0.198 10 false SL3+ 2.458,2.688 3.073,2.885 0.615,0.198 10 false SL3+ 1.313,3.635 1.927,3.833 0.615,0.198 10 false SL3- 2.458,3.635 3.073,3.833 0.615,0.198 10 false SL3- 4.417,2.698 5.031,2.896 0.615,0.198 10 false SL4+ 5.542,2.698 6.156,2.896 0.615,0.198 10 false SL4+ 4.406,3.646 5.021,3.844 0.615,0.198 10 false SL4- 5.552,3.635 6.167,3.833 0.615,0.198 10 false SL4- 1.313,4.656 1.927,4.854 0.615,0.198 10 false SL5+ 2.448,4.656 3.063,4.854 0.615,0.198 10 false SL5+ 1.302,5.594 1.917,5.792 0.615,0.198 10 false SL5- 2.448,5.594 3.063,5.792 0.615,0.198 10 false SL5- 4.406,5.594 5.021,5.792 0.615,0.198 10 false SL6- 5.563,5.594 6.177,5.792 0.615,0.198 10 false SL6- 4.417,4.646 5.031,4.844 0.615,0.198 10 false SL6+ 5.552,4.646 6.167,4.844 0.615,0.198 10 false SL6+ 1.313,6.615 1.927,6.813 0.615,0.198 10 false SLU+ 2.469,6.615 3.083,6.813 0.615,0.198 10 false SLU+ 1.292,7.552 1.906,7.75 0.615,0.198 10 false SLU- 2.448,7.552 3.063,7.75 0.615,0.198 10 false SLU- 2.24,0.625 2.396,0.823 0.156,0.198 10 false 6 1.76,0.625 2.073,0.823 0.313,0.198 10 false 23 1.75,1.573 2.063,1.771 0.313,0.198 10 false 24 2.167,1.573 2.479,1.771 0.313,0.198 10 false 25 1.771,2.698 2.083,2.896 0.313,0.198 10 false 13 2.208,2.688 2.365,2.885 0.156,0.198 10 false 7 1.76,3.635 2.073,3.833 0.313,0.198 10 false 14 2.188,3.635 2.5,3.833 0.313,0.198 10 false 26 1.771,4.656 2.083,4.854 0.313,0.198 10 false 11 2.24,4.656 2.552,4.854 0.313,0.198 10 false 3 1.75,5.594 2.063,5.792 0.313,0.198 10 false 12 2.167,5.594 2.479,5.792 0.313,0.198 10 false 22 1.771,6.615 2.083,6.813 0.313,0.198 10 false 17 2.156,6.615 2.469,6.813 0.313,0.198 10 false 4 1.75,7.552 2.063,7.75 0.313,0.198 10 false 18 2.156,7.552 2.469,7.75 0.313,0.198 10 false 23 4.865,0.625 5.177,0.823 0.313,0.198 10 false 5 5.271,0.625 5.583,0.823 0.313,0.198 10 false 19 4.854,1.573 5.167,1.771 0.313,0.198 10 false 24 5.271,1.573 5.583,1.771 0.313,0.198 10 false 20 4.854,2.698 5.167,2.896 0.313,0.198 10 false 8 5.271,2.698 5.583,2.896 0.313,0.198 10 false 15 4.844,3.646 5.156,3.844 0.313,0.198 10 false 27 5.26,3.635 5.573,3.833 0.313,0.198 10 false 16 4.865,4.646 5.177,4.844 0.313,0.198 10 false 9 5.26,4.646 5.573,4.844 0.313,0.198 10 false 25 4.865,5.594 5.177,5.792 0.313,0.198 10 false 28 5.26,5.594 5.573,5.792 0.313,0.198 10 false 26 0.531,1.146 1.458,1.479 0.927,0.333 10 false Solenoid (SL1) Valve 5.708,1.094 6.646,1.427 0.938,0.333 10 false Solenoid (SL2) Valve 0.552,3.208 1.479,3.583 0.927,0.375 10 false Solenoid (SL3) Valve 5.708,3.167 6.646,3.51 0.938,0.344 10 false Solenoid (SL4) Valve 0.531,5.177 1.469,5.521 0.938,0.344 10 false Solenoid (SL5) Valve 5.719,5.125 6.635,5.479 0.917,0.354 10 false Solenoid (SL6) Valve 0.167,8.333 0.479,8.531 0.313,0.198 10 false C33 0.167,8.5 2,8.698 1.833,0.198 10 false Transmission Wire 5.583,8.333 5.896,8.531 0.313,0.198 10 false C33 5.583,8.5 7.042,8.729 1.458,0.229 10 false Transmission Wire 3.26,8.333 3.719,8.531 0.458,0.198 10 false C36 3.26,8.49 4.5,8.729 1.24,0.24 10 false TCM 3.083,0.302 3.698,0.5 0.615,0.198 10 false 12 V 3.083,2.375 3.698,2.573 0.615,0.198 10 false 12 V 3.083,4.333 3.698,4.531 0.615,0.198 10 false 12 V 3.083,6.292 3.698,6.49 0.615,0.198 10 false 12 V 4.333,4.333 4.948,4.531 0.615,0.198 10 false 12 V 4.354,0.302 4.969,0.5 0.615,0.198 10 false 12 V 4.354,2.365 4.969,2.563 0.615,0.198 10 false 12 V 0.156,0.813 0.313,1.01 0.156,0.198 10 false 1 6.927,0.813 7.083,1.01 0.156,0.198 10 false 1 6.927,2.885 7.083,3.083 0.156,0.198 10 false 1 0.156,2.875 0.313,3.073 0.156,0.198 10 false 1 0.156,4.844 0.313,5.042 0.156,0.198 10 false 1 6.927,4.833 7.083,5.031 0.156,0.198 10 false 1 0.167,6.802 0.323,7 0.156,0.198 10 false 1 0.156,1.615 0.313,1.813 0.156,0.198 10 false 2 0.156,3.688 0.313,3.885 0.156,0.198 10 false 2 0.156,5.656 0.313,5.854 0.156,0.198 10 false 2 0.167,7.625 0.323,7.823 0.156,0.198 10 false 2 6.927,5.667 7.083,5.865 0.156,0.198 10 false 2 6.927,3.708 7.083,3.906 0.156,0.198 10 false 2 6.927,1.625 7.083,1.823 0.156,0.198 10 false 2 0.521,7.156 1.458,7.5 0.938,0.344 10 false Solenoid (SLU) Valve

C458215E02
1.281,0.917 1.896,1.115 0.615,0.198 10 false SP2B 2.417,0.917 3.031,1.115 0.615,0.198 10 false SP2B 1.271,2.135 1.885,2.333 0.615,0.198 10 false SP2O 2.417,2.135 3.031,2.333 0.615,0.198 10 false SP2O 4.573,1.458 4.885,1.656 0.313,0.198 10 false SL 5.531,1.458 5.844,1.656 0.313,0.198 10 false SL 1.458,3.281 1.771,3.479 0.313,0.198 10 false SR 2.427,3.281 2.74,3.479 0.313,0.198 10 false SR 4.51,3.281 4.969,3.479 0.458,0.198 10 false SC1 5.542,3.281 6,3.479 0.458,0.198 10 false SC1 5.302,3.271 5.458,3.469 0.156,0.198 10 false 7 4.885,3.281 5.198,3.479 0.313,0.198 10 false 46 2.167,3.281 2.479,3.479 0.313,0.198 10 false 45 1.75,3.281 1.906,3.479 0.156,0.198 10 false 6 4.854,1.469 5.167,1.667 0.313,0.198 10 false 44 5.292,1.458 5.448,1.656 0.156,0.198 10 false 5 1.729,0.917 2.042,1.115 0.313,0.198 10 false 29 1.75,2.135 2.063,2.333 0.313,0.198 10 false 30 2.156,0.917 2.469,1.115 0.313,0.198 10 false 12 2.156,2.135 2.469,2.333 0.313,0.198 10 false 31 3.073,0.604 3.531,0.802 0.458,0.198 10 false 12V 4.406,1.208 4.865,1.406 0.458,0.198 10 false 12V 4.396,3.021 4.854,3.219 0.458,0.198 10 false 12V 2.99,3.031 3.448,3.229 0.458,0.198 10 false 12V 0.552,1.49 1.406,2.354 0.854,0.865 10 false Transmission Revolution Sensor (SP2) 5.688,3.802 6.656,4.208 0.969,0.406 10 false Solenoid (SC1) Valve 0.552,3.802 1.417,4.198 0.865,0.396 10 false Solenoid (SR) Valve 5.76,1.979 6.625,2.438 0.865,0.458 10 false Solenoid (SL) Valve 3.229,4.625 3.958,4.948 0.729,0.323 10 false TCM 3.229,4.458 3.688,4.656 0.458,0.198 10 false C36 2.969,5.229 3.427,5.427 0.458,0.198 10 false C33 2.969,5.385 4.802,5.583 1.833,0.198 10 false Transmission Wire 0.135,1.24 0.292,1.438 0.156,0.198 10 false 2 0.135,2.094 0.292,2.292 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SOLENOID VALVE) - TCM)
a.

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C36)Location & Routing

Click Connector(C36)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transmission Control ECU Assembly

C36-6 (SL1+) - C36-25 (SL1-) 20°C (68°F) 5.0 to 5.6 Ω
C36-5 (SL2+) - C36-24 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
C36-7 (SL3+) - C36-26 (SL3-) 20°C (68°F) 5.0 to 5.6 Ω
C36-8 (SL4+) - C36-27 (SL4-) 20°C (68°F) 5.0 to 5.6 Ω
C36-3 (SL5+) - C36-22 (SL5-) 20°C (68°F) 5.0 to 5.6 Ω
C36-9 (SL6+) - C36-28 (SL6-) 20°C (68°F) 5.0 to 5.6 Ω
C36-4 (SLU+) - C36-23 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
C36-44 (SL) - Body ground 20°C (68°F) 11 to 15 Ω
C36-45 (SR) - Body ground 20°C (68°F) 11 to 15 Ω
C36-46 (SC1) - Body ground 20°C (68°F) 11 to 15 Ω
C36-6 (SL1+) or C36-25 (SL1-) - Body ground and other terminals Always 10 kΩ or higher
C36-5 (SL2+) or C36-24 (SL2-) - Body ground and other terminals Always 10 kΩ or higher
C36-7 (SL3+) or C36-26 (SL3-) - Body ground and other terminals Always 10 kΩ or higher
C36-8 (SL4+) or C36-27 (SL4-) - Body ground and other terminals Always 10 kΩ or higher
C36-3 (SL5+) or C36-22 (SL5-) - Body ground and other terminals Always 10 kΩ or higher
C36-9 (SL6+) or C36-28 (SL6-) - Body ground and other terminals Always 10 kΩ or higher
C36-4 (SLU+) or C36-23 (SLU-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (SPEED (SP2) AND SP2 SENSOR VOLTAGE)

NG

10.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
2.READ VALUE USING GTS (SPEED (SP2) AND SP2 SENSOR VOLTAGE)
a.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Speed (SP2) Output shaft speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
0 km/h (0 mph): Vehicle stopped
(Output shaft speed is equal to vehicle speed)
-
SP2 Sensor Voltage SP2 sensor voltage Min.: 0.000 V
Max.: 4.999 V
0.2 to 1.8 V: Idling -
Powertrain > Transmission > Data List
Tester Display
Speed (SP2)
SP2 Sensor Voltage
50003 373 362,391

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

3.CLEAR DTC

B

6.CHECK TRANSMISSION REVOLUTION SENSOR TERMINAL (SP2 TERMINAL)
3.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT (DTC P170300)
4.CHECK DTC OUTPUT (DTC P170300)

b.

Read the DTCs using the GTS.

Powertrain > Transmission > Trouble Codes
50001 373

Result:
Result Proceed to
DTCs are not output A
DTC P170300 is output B



A

END

B

5.REPLACE TCM
6.CHECK TRANSMISSION REVOLUTION SENSOR TERMINAL (SP2 TERMINAL)
a.

Disconnect the transmission wire connector.



c.

Turn the ignition switch to ON.



Result:
Proceed to
OK
NG



OK

7.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (SP2))

NG

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
7.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (SP2))
a.
C377609C09
0.094,2.219 0.5,2.479 0.406,0.26 1.667,3 1.313,2.531 true 0.906,3.01 1.188,2.531 true 2.25,1.344 1.896,0.875 true 1.385,1.344 1.667,0.865 true 0.104,0.26 0.417,0.458 0.313,0.198 10 false *a 0.104,1.823 0.417,2.021 0.313,0.198 10 false *b 1.563,3.042 2.021,3.24 0.458,0.198 10 false SP2B 0.75,3.042 1.208,3.24 0.458,0.198 10 false SP2O 2.25,1.406 2.708,1.604 0.458,0.198 10 false 1 1.323,1.406 1.781,1.604 0.458,0.198 10 false 2 0.188,2.292 0.5,2.49 0.313,0.198 10 false C33
*a Front view of wire harness connector
(to Transmission Revolution Sensor (SP2))
*b Component without harness connected
(Transmission Wire)


Disconnect the transmission revolution sensor (SP2) connector.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SPEED SENSOR>REMOVAL


b.

Disconnect the transmission wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C33)Location & Routing

Click Connector(C33)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Automatic Transmission Assembly (Transmission Wire)

Terminal 2 of the transmission revolution sensor (SP2) connector - C33-29 (SP2B) Always Below 1 Ω
Terminal 1 of the transmission revolution sensor (SP2) connector - C33-30 (SP2O) Always Below 1 Ω
Terminal 2 of the transmission revolution sensor (SP2) connector or C33-29 (SP2B) - Body ground Always 10 kΩ or higher
Terminal 1 of the transmission revolution sensor (SP2) connector or C33-30 (SP2O) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION REVOLUTION SENSOR (SP2)

NG

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the transmission wire connector.


b.

Disconnect the TCM connector.



Result:
Proceed to
OK
NG



OK

9.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the transmission wire connector.


b.

Disconnect the TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C33,C36)Location & Routing

Click Connector(C33)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Automatic Transmission Assembly (Transmission Wire)

Click Connector(C36)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transmission Control ECU Assembly

C33-23 (SL1+) - C36-6 (SL1+) Always Below 1 Ω
C33-24 (SL1-) - C36-25 (SL1-) Always Below 1 Ω
C33-19 (SL2+) - C36-5 (SL2+) Always Below 1 Ω
C33-20 (SL2-) - C36-24 (SL2-) Always Below 1 Ω
C33-13 (SL3+) - C36-7 (SL3+) Always Below 1 Ω
C33-14 (SL3-) - C36-26 (SL3-) Always Below 1 Ω
C33-15 (SL4+) - C36-8 (SL4+) Always Below 1 Ω
C33-16 (SL4-) - C36-27 (SL4-) Always Below 1 Ω
C33-11 (SL5+) - C36-3 (SL5+) Always Below 1 Ω
C33-12 (SL5-) - C36-22 (SL5-) Always Below 1 Ω
C33-25 (SL6+) - C36-9 (SL6+) Always Below 1 Ω
C33-26 (SL6-) - C36-28 (SL6-) Always Below 1 Ω
C33-17 (SLU+) - C36-4 (SLU+) Always Below 1 Ω
C33-18 (SLU-) - C36-23 (SLU-) Always Below 1 Ω
C33-5 (SL) - C36-44 (SL) Always Below 1 Ω
C33-6 (SR) - C36-45 (SL) Always Below 1 Ω
C33-7 (SC1) - C36-46 (SC1) Always Below 1 Ω
C33-23 (SL1+) or C36-6 (SL1+) - Body ground and other terminals Always 10 kΩ or higher
C33-24 (SL1-) or C36-25 (SL1-) - Body ground and other terminals Always 10 kΩ or higher
C33-19 (SL2+) or C36-5 (SL2+) - Body ground and other terminals Always 10 kΩ or higher
C33-20 (SL2-) or C36-24 (SL2-) - Body ground and other terminals Always 10 kΩ or higher
C33-13 (SL3+) or C36-7 (SL3+) - Body ground and other terminals Always 10 kΩ or higher
C33-14 (SL3-) or C36-26 (SL3-) - Body ground and other terminals Always 10 kΩ or higher
C33-15 (SL4+) or C36-8 (SL4+) - Body ground and other terminals Always 10 kΩ or higher
C33-16 (SL4-) or C36-27 (SL4-) - Body ground and other terminals Always 10 kΩ or higher
C33-11 (SL5+) or C36-3 (SL5+) - Body ground and other terminals Always 10 kΩ or higher
C33-12 (SL5-) or C36-22 (SL5-) - Body ground and other terminals Always 10 kΩ or higher
C33-25 (SL6+) or C36-9 (SL6+) - Body ground and other terminals Always 10 kΩ or higher
C33-26 (SL6-) or C36-28 (SL6-) - Body ground and other terminals Always 10 kΩ or higher
C33-17 (SLU+) or C36-4 (SLU+) - Body ground and other terminals Always 10 kΩ or higher
C33-18 (SLU-) or C36-23 (SLU-) - Body ground and other terminals Always 10 kΩ or higher
C33-5 (SL) or C36-44 (SL) - Body ground and other terminals Always 10 kΩ or higher
C33-6 (SR) or C36-45 (SR) - Body ground and other terminals Always 10 kΩ or higher
C33-7 (SC1) or C36-46 (SC1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5), (SL6), (SLU), (SL), (SR) AND (SC1) VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT SOLENOID VALVE - TCM)

11.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5), (SL6), (SLU), (SL), (SR) AND (SC1) VALVE

OK

NG

REPLACE SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5), (SL6), (SLU), (SL), (SR) OR (SC1) VALVE