Home › Drivetrain › AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV) › from 2021.07
RM38G0E _52 Drivetrain _100435 AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE _0488019 AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV) C

AJA0F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for F33A-FTV)  P274015  Transmission Fluid Temperature Sensor "B" Circuit Short to Battery or Open  


DESCRIPTION

The No. 2 ATF temperature sensor converts the fluid temperature into a resistance value for use by the TCM.

The TCM applies a voltage to the temperature sensor through terminal THOC of the TCM.

The sensor resistance changes with the No. 2 ATF temperature. As the temperature becomes higher, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance and voltage goes down as the temperature becomes higher.

The TCM calculates the fluid temperature based on the voltage signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P274015 Transmission Fluid Temperature Sensor "B" Circuit Short to Battery or Open No. 2 ATF temperature sensor voltage is higher than 4.915 V for 0.5 seconds or more and either condition is met (1 trip detection logic):
·

15 minutes or more have elapsed after the engine start when the engine coolant temperature or intake air temperature is -29.375°C (-20.875°F) or less.

·

10 seconds or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are higher than -29.375°C (-20.875°F).


·

Open or short in No. 2 ATF temperature sensor circuit

·

Transmission wire (No. 2 ATF temperature sensor)

·

TCM


Does not come on DTC stored SAE: P2743

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition 15 minutes or more have elapsed after the engine start when the engine coolant temperature or intake air temperature is -29.375°C (-20.875°F) or less. ○ -
10 seconds or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are higher than -29.375°C (-20.875°F). - ○
Malfunction Condition No. 2 ATF temperature sensor voltage is higher than 4.915 V ○ ○
Duration 0.5 seconds or more 0.5 seconds or more
Detection Logic 1 trip detection logic 1 trip detection logic

HINT:

This DTC is stored when either of the above detection patterns are met.


MONITOR DESCRIPTION

This DTC indicates an open or short in the No. 2 ATF temperature sensor circuit. The No. 2 ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature, and can detect an open or short in the No. 2 ATF temperature sensor circuit. If the resistance value of the No. 2 ATF temperature sensor is higher than 156 kΩ*, the TCM interprets this as a malfunction of the No. 2 ATF temperature sensor or in the wire harness, illuminates the MIL and stores this DTC.

*: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for at least 30 seconds.

3.

Wait for 15 minutes or more with the engine started.

4.

Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

5.

Input the DTC: P274015.

6.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 2 ATF TEMPERATURE SENSOR - TCM)
a.

Disconnect the TCM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C36)Location & Routing

Click Connector(C36)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Transmission Control ECU Assembly

C36-54 (THOC) - C36-55 (ETH2) Always 25 Ω to 156 kΩ
C36-54 (THOC) - Other terminals Always 10 kΩ or higher
C36-55 (ETH2) - Other terminals Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

ATF Temperature Specified Condition
10°C (50°F) 5 to 8 kΩ
25°C (77°F) 2.5 to 4.5 kΩ
110°C (230°F) 0.22 to 0.28 kΩ



Result:
Proceed to
OK
NG



OK

2.REPLACE TCM

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the transmission wire connector.


b.

Disconnect the TCM connector.



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE TRANSMISSION WIRE (NO. 2 ATF TEMPERATURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR