If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, telephone transceiver assembly or speakers.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for 14 Speakers | A |
| for 10 Speakers | B |
A
B
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
Perform the operation check above and determine the speaker that is not operating.
If sound cannot be heard from any speaker, inspect all of them.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly and front No. 2 speaker assembly | A |
| Front No. 3 speaker assembly and front No. 4 speaker assembly | B |
| Rear No. 2 speaker assembly and rear speaker assembly | C |
| Rear No. 3 speaker assembly | D |
| No. 1 speaker with box assembly | E |
A
B
C
D
E
Disconnect the S22 stereo component amplifier assembly connector.
Disconnect the M9 and N7 front No. 1 speaker assembly connectors.
Disconnect the I145 and I146 front No. 2 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(S22,I146,N7,I145,M9)Location & Routingewd_type=routing;type=c,c,c,c,c;code=S22,I146,N7,I145,M9 Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=S22;pinno=11,26,15,30 Click Connector(N7)Body>Front Door Wire LH>Front No. 1 Speaker Assembly LHewd_type=component;type=c;code=N7;pinno=2,1 Click Connector(M9)Body>Front Door Wire RH>Front No. 1 Speaker Assembly RHewd_type=component;type=c;code=M9;pinno=2,1 |
||
| S22-11 (FL+) - I146-4 (+) | Always | Below 1 Ω |
| S22-26 (FL-) - I146-2 (-) | Always | Below 1 Ω |
| I146-3 (TWR+) - N7-2 (+) | Always | Below 1 Ω |
| I146-1 (TWR-) - N7-1 (-) | Always | Below 1 Ω |
| S22-15 (FR+) - I145-4 (+) | Always | Below 1 Ω |
| S22-30 (FR-) - I145-2 (-) | Always | Below 1 Ω |
| I145-3 (TWR+) - M9-2 (+) | Always | Below 1 Ω |
| I145-1 (TWR-) - M9-1 (-) | Always | Below 1 Ω |
| S22-11 (FL+) - Body ground | Always | 10 kΩ or higher |
| S22-26 (FL-) - Body ground | Always | 10 kΩ or higher |
| I146-3 (TWR+) - Body ground | Always | 10 kΩ or higher |
| I146-1 (TWR-) - Body ground | Always | 10 kΩ or higher |
| S22-15 (FR+) - Body ground | Always | 10 kΩ or higher |
| S22-30 (FR-) - Body ground | Always | 10 kΩ or higher |
| I145-3 (TWR+) - Body ground | Always | 10 kΩ or higher |
| I145-1 (TWR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*: w/ Telematics System (for Toyota Connected Services)
Disconnect the S22 stereo component amplifier assembly connector.
Disconnect the J2 and L2 front No. 3 speaker assembly connectors.
Disconnect the K2 front No. 4 speaker assembly connector.
Disconnect the I56 telephone transceiver assembly connector.*
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: w/o Telematics Transceiver or w/ Telematics System (for ERA-GLONASS) *2: w/ Telematics System (for Toyota Connected Services) |
||
Click Location & Routing(S22,J2,L2,I56,K2)Location & Routingewd_type=routing;type=c,c,c,c,c;code=S22,J2,L2,I56,K2 Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=S22;pinno=14,29,13,28,10,25 Click Connector(J2)Instrument Panel>No. 2 Instrument Panel Wire>Front No. 2 Speaker Assembly RHewd_type=component;type=c;code=J2;pinno=2,1 Click Connector(L2)Instrument Panel>No. 4 Instrument Panel Wire>Front No. 2 Speaker Assembly LHewd_type=component;type=c;code=L2;pinno=2,1 Click Connector(K2)Instrument Panel>No. 3 Instrument Panel Wire>Front No. 4 Speaker Assemblyewd_type=component;type=c;code=K2;pinno=2,1 |
||
| S22-14 (TWR+) - J2-2 (+) | Always | Below 1 Ω |
| S22-29 (TWR-) - J2-1 (-) | Always | Below 1 Ω |
| S22-13 (TWL+) - L2-2 (+)*1 | Always | Below 1 Ω |
| S22-28 (TWL-) - L2-1 (-)*1 | Always | Below 1 Ω |
| S22-13 (TWL+) - I56-1 (SPI+)*2 | Always | Below 1 Ω |
| S22-28 (TWL-) - I56-2 (SPI-)*2 | Always | Below 1 Ω |
| I56-3 (SPO+) - L2-2 (+)*2 | Always | Below 1 Ω |
| I56-4 (SPO-) - L2-1 (-)*2 | Always | Below 1 Ω |
| S22-10 (CTR+) - K2-2 (+) | Always | Below 1 Ω |
| S22-25 (CTR-) - K2-1 (-) | Always | Below 1 Ω |
| S22-14 (TWR+) - Body ground | Always | 10 kΩ or higher |
| S22-29 (TWR-) - Body ground | Always | 10 kΩ or higher |
| S22-13 (TWL+) - Body ground | Always | 10 kΩ or higher |
| S22-28 (TWL-) - Body ground | Always | 10 kΩ or higher |
| I56-3 (SPO+) - Body ground*2 | Always | 10 kΩ or higher |
| I56-4 (SPO-) - Body ground*2 | Always | 10 kΩ or higher |
| S22-10 (CTR+) - Body ground | Always | 10 kΩ or higher |
| S22-25 (CTR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/ Telematics System (for Toyota Connected Services) | A |
| w/o Telematics Transceiver or w/ Telematics System (for ERA-GLONASS) | B |
A
B
| *a | Component without harness connected (Telephone Transceiver Assembly) |
Remove the telephone transceiver assembly.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (SPO+) - 1 (SPI+) | Always | Below 1 Ω |
| 4 (SPO-) - 2 (SPI-) | Always | Below 1 Ω |
| 1 (SPI+) - 2 (SPI-) | Always | 10 kΩ or higher |
| 3 (SPO+) - 4 (SPO-) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the S22 stereo component amplifier assembly connector.
Disconnect the O10 and P9 rear speaker assembly connectors.
Disconnect the O11 and P11 rear No. 2 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(S22,O11,O10,P11,P9)Location & Routingewd_type=routing;type=c,c,c,c,c;code=S22,O11,O10,P11,P9 Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=S22;pinno=12,27,4,19 Click Connector(O11)Body>No. 1 Rear Door Wire>No. 2 Rear Speaker Assembly RHewd_type=component;type=c;code=O11;pinno=4,2,3,1 Click Connector(O10)Body>No. 1 Rear Door Wire>Rear Speaker Assembly RHewd_type=component;type=c;code=O10;pinno=2,1 Click Connector(P11)Body>No. 2 Rear Door Wire>No. 2 Rear Speaker Assembly LHewd_type=component;type=c;code=P11;pinno=4,2,3,1 Click Connector(P9)Body>No. 2 Rear Door Wire>Rear Speaker Assembly LHewd_type=component;type=c;code=P9;pinno=2,1 |
||
| S22-12 (RR+) - O11-4 (+) | Always | Below 1 Ω |
| S22-27 (RR-) - O11-2 (-) | Always | Below 1 Ω |
| O11-3 (+) - O10-2 (WF+) | Always | Below 1 Ω |
| O11-1 (-) - O10-1 (WF-) | Always | Below 1 Ω |
| S22-4 (RL+) - P11-4 (+) | Always | Below 1 Ω |
| S22-19 (RL-) - P11-2 (-) | Always | Below 1 Ω |
| P11-3 (+) - P9-2 (WF+) | Always | Below 1 Ω |
| P11-1 (-) - P9-1 (WF-) | Always | Below 1 Ω |
| S22-12 (RR+) - Body ground | Always | 10 kΩ or higher |
| S22-27 (RR-) - Body ground | Always | 10 kΩ or higher |
| O11-3 (+) - Body ground | Always | 10 kΩ or higher |
| O11-1 (-) - Body ground | Always | 10 kΩ or higher |
| S22-4 (RL+) - Body ground | Always | 10 kΩ or higher |
| S22-19 (RL-) - Body ground | Always | 10 kΩ or higher |
| P11-3 (+) - Body ground | Always | 10 kΩ or higher |
| P11-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left rear speaker is defective, inspect by interchanging the right one with the left one.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the S22 stereo component amplifier assembly connector.
Disconnect the g12 and g13 rear No. 3 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(S22,g12,g13)Location & Routingewd_type=routing;type=c,c,c;code=S22,g12,g13 Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=S22;pinno=9,24,5,20 Click Connector(g12)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>No. 3 Rear Speaker Assembly RHewd_type=component;type=c;code=g12;pinno=2,1 Click Connector(g13)Body>No. 1 Rear Window Wire / No. 2 Back Door Wire>No. 3 Rear Speaker Assembly LHewd_type=component;type=c;code=g13;pinno=2,1 |
||
| S22-9 (SR+) - g12-2 (RRD+) | Always | Below 1 Ω |
| S22-24 (SR-) - g12-1 (RRD-) | Always | Below 1 Ω |
| S22-5 (SL+) - g13-2 (RLD+) | Always | Below 1 Ω |
| S22-20 (SL-) - g13-1 (RLD-) | Always | Below 1 Ω |
| S22-9 (SR+) - Body ground | Always | 10 kΩ or higher |
| S22-24 (SR-) - Body ground | Always | 10 kΩ or higher |
| S22-5 (SL+) - Body ground | Always | 10 kΩ or higher |
| S22-20 (SL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>BACK DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the S22 stereo component amplifier assembly connector.
Disconnect the T16 No. 1 speaker with box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(S22,T16)Location & Routingewd_type=routing;type=c,c;code=S22,T16 Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=S22;pinno=8,23,7,22 Click Connector(T16)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>No. 1 Speaker with Box Assemblyewd_type=component;type=c;code=T16;pinno=2,1,4,3 |
||
| S22-8 (WF1+) - T16-2 (WF1+) | Always | Below 1 Ω |
| S22-23 (WF1-) - T16-1 (WF1-) | Always | Below 1 Ω |
| S22-7 (WF2+) - T16-4 (WF2+) | Always | Below 1 Ω |
| S22-22 (WF2-) - T16-3 (WF2-) | Always | Below 1 Ω |
| S22-8 (WF1+) - Body ground | Always | 10 kΩ or higher |
| S22-23 (WF1-) - Body ground | Always | 10 kΩ or higher |
| S22-7 (WF2+) - Body ground | Always | 10 kΩ or higher |
| S22-22 (WF2-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
Perform the operation check above and determine the speaker that is not operating.
If sound cannot be heard from any speaker, inspect all of them.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly | A |
| Front No. 3 speaker assembly and front No. 4 speaker assembly | B |
| Rear speaker assembly | C |
| No. 1 speaker with box assembly | D |
A
B
C
D
Disconnect the S22 stereo component amplifier assembly connector.
Disconnect the M9 and N7 front No. 1 speaker assembly connectors.
Disconnect the J3 and L1 front No. 2 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(S22,N7,M9,L1,J3)Location & Routingewd_type=routing;type=c,c,c,c,c;code=S22,N7,M9,L1,J3 Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=S22;pinno=4,19,5,20,12,27,13,28 Click Connector(N7)Body>Front Door Wire LH>Front No. 1 Speaker Assembly LHewd_type=component;type=c;code=N7;pinno=2,1 Click Connector(M9)Body>Front Door Wire RH>Front No. 1 Speaker Assembly RHewd_type=component;type=c;code=M9;pinno=2,1 Click Connector(L1)Instrument Panel>No. 4 Instrument Panel Wire>Front No. 2 Speaker Assembly LHewd_type=component;type=c;code=L1;pinno=2,1 Click Connector(J3)Instrument Panel>No. 2 Instrument Panel Wire>Front No. 2 Speaker Assembly RHewd_type=component;type=c;code=J3;pinno=2,1 |
||
| S22-4 (FL+) - N7-2 (+) | Always | Below 1 Ω |
| S22-19 (FL-) - N7-1 (-) | Always | Below 1 Ω |
| S22-5 (FR+) - M9-2 (+) | Always | Below 1 Ω |
| S22-20 (FR-) - M9-1 (-) | Always | Below 1 Ω |
| S22-12 (TWL+) - L1-2 (+) | Always | Below 1 Ω |
| S22-27 (TWL-) - L1-1 (-) | Always | Below 1 Ω |
| S22-13 (TWR+) - J3-2 (+) | Always | Below 1 Ω |
| S22-28 (TWR-) - J3-1 (-) | Always | Below 1 Ω |
| S22-4 (FL+) - Body ground | Always | 10 kΩ or higher |
| S22-19 (FL-) - Body ground | Always | 10 kΩ or higher |
| S22-5 (FR+) - Body ground | Always | 10 kΩ or higher |
| S22-20 (FR-) - Body ground | Always | 10 kΩ or higher |
| S22-12 (TWL+) - Body ground | Always | 10 kΩ or higher |
| S22-27 (TWL-) - Body ground | Always | 10 kΩ or higher |
| S22-13 (TWR+) - Body ground | Always | 10 kΩ or higher |
| S22-28 (TWR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*: w/ Telematics System (for Toyota Connected Services)
Disconnect the S22 stereo component amplifier assembly connector.
Disconnect the J3 and L1 front No. 3 speaker assembly connectors.
Disconnect the K1 front No. 4 speaker assembly connector.
Disconnect the I56 telephone transceiver assembly connector.*
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: w/o Telematics Transceiver or w/ Telematics System (for ERA-GLONASS) *2: w/ Telematics System (for Toyota Connected Services) |
||
Click Location & Routing(S22,J3,L1,I56,K1)Location & Routingewd_type=routing;type=c,c,c,c,c;code=S22,J3,L1,I56,K1 Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=S22;pinno=13,28,12,27,7,22 Click Connector(J3)Instrument Panel>No. 2 Instrument Panel Wire>Front No. 2 Speaker Assembly RHewd_type=component;type=c;code=J3;pinno=2,1 Click Connector(L1)Instrument Panel>No. 4 Instrument Panel Wire>Front No. 2 Speaker Assembly LHewd_type=component;type=c;code=L1;pinno=2,1 Click Connector(K1)Instrument Panel>No. 3 Instrument Panel Wire>Front No. 4 Speaker Assemblyewd_type=component;type=c;code=K1;pinno=2,1 |
||
| S22-13 (TWR+) - J3-2 (+) | Always | Below 1 Ω |
| S22-28 (TWR-) - J3-1 (-) | Always | Below 1 Ω |
| S22-12 (TWL+) - L1-2 (+)*1 | Always | Below 1 Ω |
| S22-27 (TWL-) - L1-1 (-)*1 | Always | Below 1 Ω |
| S22-12 (TWL+) - I56-1 (SPI+)*2 | Always | Below 1 Ω |
| S22-27 (TWL-) - I56-2 (SPI-)*2 | Always | Below 1 Ω |
| I56-3 (SPO+) - L1-1 (-)*2 | Always | Below 1 Ω |
| I56-4 (SPO-) - L1-1 (-)*2 | Always | Below 1 Ω |
| S22-7 (CTR+) - K1-2 (+) | Always | Below 1 Ω |
| S22-22 (CTR-) - K1-1 (-) | Always | Below 1 Ω |
| S22-13 (TWR+) - Body ground | Always | 10 kΩ or higher |
| S22-28 (TWR-) - Body ground | Always | 10 kΩ or higher |
| S22-12 (TWL+) - Body ground | Always | 10 kΩ or higher |
| S22-27 (TWL-) - Body ground | Always | 10 kΩ or higher |
| I56-3 (SPO+) - Body ground*2 | Always | 10 kΩ or higher |
| I56-4 (SPO-) - Body ground*2 | Always | 10 kΩ or higher |
| S22-7 (CTR+) - Body ground | Always | 10 kΩ or higher |
| S22-22 (CTR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle type.
| Result | Proceed to |
|---|---|
| w/ Telematics System (for Toyota Connected Services) | A |
| w/o Telematics Transceiver or w/ Telematics System (for ERA-GLONASS) | B |
A
B
| *a | Component without harness connected (Telephone Transceiver Assembly) |
Remove the telephone transceiver assembly.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (SPO+) - 1 (SPI+) | Always | Below 1 Ω |
| 4 (SPO-) - 2 (SPI-) | Always | Below 1 Ω |
| 1 (SPI+) - 2 (SPI-) | Always | 10 kΩ or higher |
| 3 (SPO+) - 4 (SPO-) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the S22 stereo component amplifier assembly connector.
Disconnect the O9 and P10 rear speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(S22,O9,P10)Location & Routingewd_type=routing;type=c,c,c;code=S22,O9,P10 Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=S22;pinno=9,24,8,23 Click Connector(O9)Body>No. 1 Rear Door Wire>Rear Speaker Assembly RHewd_type=component;type=c;code=O9;pinno=2,1 Click Connector(P10)Body>No. 2 Rear Door Wire>Rear Speaker Assembly LHewd_type=component;type=c;code=P10;pinno=2,1 |
||
| S22-9 (RR+) - O9-2 (WF+) | Always | Below 1 Ω |
| S22-24 (RR-) - O9-1 (WF-) | Always | Below 1 Ω |
| S22-8 (RL+) - P10-2 (WF+) | Always | Below 1 Ω |
| S22-23 (RL-) - P10-1 (WF-) | Always | Below 1 Ω |
| S22-9 (RR+) - Body ground | Always | 10 kΩ or higher |
| S22-24 (RR-) - Body ground | Always | 10 kΩ or higher |
| S22-8 (RL+) - Body ground | Always | 10 kΩ or higher |
| S22-23 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the S22 stereo component amplifier assembly connector.
Disconnect the T15 No. 1 speaker with box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(S22,T15)Location & Routingewd_type=routing;type=c,c;code=S22,T15 Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assemblyewd_type=component;type=c;code=S22;pinno=6,21 Click Connector(T15)Body>No. 3 Floor Wire / Theft Warning Sensor Cord Sub-Assembly>No. 1 Speaker with Box Assemblyewd_type=component;type=c;code=T15;pinno=2,1 |
||
| S22-6 (WF1+) - T15-2 (WF1+) | Always | Below 1 Ω |
| S22-21 (WF1-) - T15-1 (WF1-) | Always | Below 1 Ω |
| S22-6 (WF1+) - Body ground | Always | 10 kΩ or higher |
| S22-21 (WF1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>LUGGAGE SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG