The combination meter assembly and engine oil level sensor are connected via direct line. The combination meter assembly determines the engine oil level based on the engine oil level sensor signal.
As the engine oil level may be unstable when the engine is cold or running at high speeds, the combination meter assembly receives the engine coolant temperature signal and engine speed signal from the ECM via CAN communication in order to prevent the oil level warnings from being output erroneously.
for V35A-FTS, F33A-FTV:
for 1GR-FE:
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
The following troubleshooting procedure is based on the assumption that the SFI system is normal. Confirm that the SFI*1 or ECD*2 system is not malfunctioning before performing the following procedure.
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for F33A-FTV (w/ DPF):
for F33A-FTV (w/o DPF):
*1: for Gasoline
*2: for Diesel
When the combination meter assembly is replaced, update the ECU security key.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (LUBRICATION)>OIL LEVEL SENSOR>INSPECTION
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (LUBRICATION)>OIL PAN AND OIL LEVEL SENSOR>INSPECTION
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (LUBRICATION)>OIL PAN AND OIL LEVEL SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (LUBRICATION)>OIL LEVEL SENSOR>REMOVAL
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (LUBRICATION)>OIL PAN AND OIL LEVEL SENSOR>REMOVAL
for F33A-FTV:
Click hereEngine / Hybrid System>F33A-FTV (LUBRICATION)>OIL PAN AND OIL LEVEL SENSOR>REMOVAL
Disconnect the I6 combination meter assembly connector.
Disconnect the C26*1 or C78*2 orC175*3 engine oil level sensor connector.
*1: for V35A-FTS
*2: for 1GR-FE
*3: for F33A-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I6,C26)Location & Routingewd_type=routing;type=c,c;code=I6,C26 |
||
| I6-10 (OILW) - C26-1 (LOIL) | Always | Below 1 Ω |
| I6-10 (OILW) or C26-1 (LOIL) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I6,C78)Location & Routingewd_type=routing;type=c,c;code=I6,C78 |
||
| I6-10 (OILW) - C78-1 (LVL) | Always | Below 1 Ω |
| C78-2 (E) - Body ground | Always | Below 1 Ω |
| I6-10 (OILW) or C78-1 (LVL) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I6,C175)Location & Routingewd_type=routing;type=c,c;code=I6,C175 |
||
| I6-10 (OILW) - C175-1 (LVL) | Always | Below 1 Ω |
| I6-10 (OILW) or C175-1 (LVL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG