Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2021.07
RM38G0E _58 Vehicle Interior _100611 METER / GAUGE / DISPLAY _0467504 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the certification ECU (smart key ECU assembly) which uses this information to create the vehicle speed signal*a. The vehicle speed signal consists of pulses sent to the combination meter assembly from the certification ECU (smart key ECU assembly). To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the No. 2 skid control ECU. The pulse signal is created by switching the transistor in the certification ECU (smart key ECU assembly) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the certification ECU (smart key ECU assembly). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.

*a: This vehicle speed signal is created by the certification ECU (smart key ECU assembly). There is no actual component that is referred to as the vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

E465057E02
5.208,3.938 7.135,4.333 1.927,0.396 10 false Combination Meter Assembly 0.469,7.052 2.229,7.552 1.76,0.5 10 false Stereo Component Amplifier Assembly*3 0.479,6.896 3.385,7.375 2.906,0.479 10 false S22 5.188,6.875 5.885,7.167 0.698,0.292 10 false I11 0.75,5.365 3.135,5.938 2.385,0.573 10 false Navigation ECU*2 1.781,1.375 2.219,1.563 0.438,0.188 10 false SPDO 5.417,1.26 5.625,1.438 0.208,0.177 10 false SI 5.813,0.958 6.219,1.365 0.406,0.406 10 false 12 V 5.427,3.021 5.656,3.208 0.229,0.188 10 false +S 1.458,3.021 1.813,3.208 0.354,0.188 10 false SPD 1.219,1.375 1.552,1.573 0.333,0.198 10 false SPD 5.448,6.417 5.792,6.604 0.344,0.188 10 false SPD 5.438,4.75 5.792,4.958 0.354,0.208 10 false SPD 1.188,0.406 5.5,0.719 4.313,0.313 10 false Break Actuator Assembly (No. 2 Skid Control ECU) 5.219,3.771 5.625,4.177 0.406,0.406 10 false I6 5.135,3.021 5.365,3.198 0.229,0.177 10 false 35 5.167,1.26 5.406,1.458 0.24,0.198 10 false 18 2.344,1.177 2.75,1.583 0.406,0.406 10 false 28 0.885,3.479 2.292,3.938 1.406,0.458 10 false B1*5, B2*6, B70*7 1.458,4.76 1.771,4.938 0.313,0.177 10 false SPD 1.854,4.75 2,4.938 0.146,0.188 10 false 9 0.771,5.198 1.677,5.969 0.906,0.771 10 false I21 1.469,6.427 1.781,6.625 0.313,0.198 10 false SPD 0.865,1.188 1.365,1.594 0.5,0.406 10 false 13 0.938,1.885 2.76,2.417 1.823,0.531 10 false Certification ECU (Smart Key ECU Assembly) 5.354,5.385 7.063,5.604 1.708,0.219 10 false Radio Receiver Assembly*4 4.656,4.76 5.323,5 0.667,0.24 10 false 17*8, 27*9 5.354,5.229 6.906,5.99 1.552,0.76 10 false I9*8, I10*9 5.177,6.427 5.375,6.604 0.198,0.177 10 false 27 1.844,6.427 2.813,6.656 0.969,0.229 10 false 16*10, 17*11 2.333,1.375 2.583,1.531 0.25,0.156 10 false I39 0.854,1.375 1.094,1.552 0.24,0.177 10 false I40 1.854,3.021 3.281,3.354 1.427,0.333 10 false 33*5, 44*6, 15*7 0.885,3.656 1.573,3.948 0.688,0.292 10 false ECM 0.073,7.563 2.823,7.844 2.75,0.281 10 false *1: for Radio and Display Type 2.115,7.563 3.802,7.76 1.688,0.198 10 false *5: for V35A-FTS 2.115,7.865 4.865,8.063 2.75,0.198 10 false *6: for 1GR-FE 5.198,7.073 6.917,7.521 1.719,0.448 10 false Radio and Display Receiver Assembly*1 0.073,8.469 2.865,8.646 2.792,0.177 10 false *4: for Radio Receiver Type 0.073,7.865 2.823,8.063 2.75,0.198 10 false *2: w/ Navigation System 0.073,8.167 1.76,8.365 1.688,0.198 10 false *3: for 12.3 Inch Display 2.115,8.479 3.792,8.677 1.677,0.198 10 false *8: w/o Multi-display 2.115,8.177 3.792,8.375 1.677,0.198 10 false *7: for F33A-FTV 4.26,5.01 5.969,5.229 1.708,0.219 10 false *4 3.792,7.552 5.469,7.75 1.677,0.198 10 false *9: w/ Multi-display 3.781,7.865 5.458,8.063 1.677,0.198 10 false *10: for 10 Speaker 3.781,8.198 5.458,8.396 1.677,0.198 10 false *11: for 14 Speaker

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

When the combination meter assembly is replaced, update the ECU security key.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY



PROCEDURE

1.CHECK DTC (ENTRY AND START SYSTEM)
a.

Check if entry and start system DTCs are output.

Body Electrical > Power Source Control > Trouble Codes
50001 454

Result:
Proceed to
OK
NG



OK

2.CHECK ECU TERMINAL VOLTAGE (INPUT VOLTAGE)

NG

2.CHECK ECU TERMINAL VOLTAGE (INPUT VOLTAGE)
C406366C72
1.5,0.125 1.885,0.385 0.385,0.26 2.333,1.396 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.656,0.188 1.969,0.344 0.313,0.156 10 false I6 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


a.

Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-35 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



Result:
Proceed to
OK
NG



OK

3.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

6.CHECK HARNESS AND CONNECTOR (EACH ECU - COMBINATION METER ASSEMBLY)
3.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.
C435456C03
1.396,0.667 1.917,0.958 0.521,0.292 2.417,2.625 2.833,1.333 2.833,1.333 2.583,1.333 true 1.583,0.75 2.198,0.948 0.615,0.198 10 false I39 0.125,0.094 0.5,0.333 0.375,0.24 12 false *a 2.156,1.25 2.771,1.448 0.615,0.198 10 false SPDO
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I39)Location & Routing

Click Connector(I39)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I39-28 (SPDO) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
4.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
E391284C44
1.448,0.438 1.865,0.667 0.417,0.229 1.344,1.292 0.542,0.792 0.542,0.792 0.385,0.792 true 1.604,0.469 1.917,0.667 0.313,0.198 10 false I6 0.208,0.729 0.521,0.927 0.313,0.198 10 false SI 2.948,3.698 3.406,3.896 0.458,0.198 10 false GND 1.281,3.979 1.438,4.177 0.156,0.198 10 false A 0.177,0.24 0.49,0.438 0.313,0.198 10 false *a 0.448,2.458 0.76,2.656 0.313,0.198 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


a.

Check the input waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


ii.

Connect an oscilloscope to terminal I6-18 (SI) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester connection I6-18 (SI) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I6 combination meter assembly connector.


b.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (EACH ECU - COMBINATION METER ASSEMBLY)

*1: for Radio and Display Type

*2: w/ Navigation System

*3: for 12.3 Inch Display

*4: for Radio Receiver Type

*5: for V35A-FTS

*6: for 1GR-FE

*7: for F33A-FTV

*8: w/o Multi-display

*9: w/ Multi-display

*10: for 10 Speaker

*11: for 14 Speaker


a.
C406366C72
1.5,0.125 1.885,0.385 0.385,0.26 2.333,1.396 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.656,0.188 1.969,0.344 0.313,0.156 10 false I6 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the I11 radio and display receiver assembly connector.*1


c.

Disconnect the I9*8 or I10*9 radio receiver assembly connector.*4


d.

Disconnect the I21 navigation ECU connector.*2


e.

Disconnect the S22 stereo component amplifier assembly connector.*3


f.

Disconnect the B1*5, B2*6, B70*7 ECM connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I6,I9,I10,I11,I21,S22,B1,B2,B70)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

Click Connector(I9)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(I10)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio Receiver Assembly

Click Connector(I11)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Radio & Display Receiver Assembly

Click Connector(I21)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Navigation ECU Assembly

Click Connector(S22)Body>No. 2 Floor Wire / Step Rear Floor Wire LH>Stereo Component Amplifier Assembly

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

Click Connector(B2)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

I6-35 (+S) - I9-17 (SPD)*4*8 Always Below 1 Ω
I6-35 (+S) - I10-27 (SPD)*4*9 Always Below 1 Ω
I6-35 (+S) - I11-27 (SPD)*1 Always Below 1 Ω
I6-35 (+S) - I21-9 (SPD)*2 Always Below 1 Ω
I6-35 (+S) - S22-16 (SPD)*3*10 Always Below 1 Ω
I6-35 (+S) - S22-17 (SPD)*3*11 Always Below 1 Ω
I6-35 (+S) - B1-33 (SPD)*5 Always Below 1 Ω
I6-35 (+S) - B2-44 (SPD)*6 Always Below 1 Ω
I6-35 (+S) - B70-15 (SPD)*7 Always Below 1 Ω
I6-35 (+S) or I9-17 (SPD)*4*8 or I10-27 (SPD)*4*9 or I11-27 (SPD)*1 or I21-9 (SPD)*2 or S22-16 (SPD)*3*10 or S22-17 (SPD)*3*11 or B1-33*5 or B2-44*6 or B70-15 (SPD)*7 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Navigation System A
w/o Navigation System B



A

8.CHECK NAVIGATION ECU

B

13.CHECK VEHICLE TYPE
8.CHECK NAVIGATION ECU
a.
C406366C72
1.5,0.125 1.885,0.385 0.385,0.26 2.333,1.396 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.656,0.188 1.969,0.344 0.313,0.156 10 false I6 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the I21 navigation ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-35 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the navigation ECU.



Result:
Proceed to
OK
NG



OK

NG

9.CHECK VEHICLE TYPE
9.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for Radio Receiver Type, with Multi-display A
except Radio Receiver Type, with Multi-display B



A

10.CHECK RADIO RECEIVER ASSEMBLY

B

11.CHECK VEHICLE TYPE
10.CHECK RADIO RECEIVER ASSEMBLY
a.
C406366C72
1.5,0.125 1.885,0.385 0.385,0.26 2.333,1.396 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.656,0.188 1.969,0.344 0.313,0.156 10 false I6 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the I9*1 or I10*2 radio receiver assembly connector.

*1: w/o Multi-display

*2: w/ Multi-display



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-35 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the radio receiver assembly.



Result:
Proceed to
OK
NG



OK

NG

11.CHECK VEHICLE TYPE
11.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for Radio and Display Type A
except Radio and Display Type B



A

12.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

B

13.CHECK VEHICLE TYPE
12.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
C406366C72
1.5,0.125 1.885,0.385 0.385,0.26 2.333,1.396 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.656,0.188 1.969,0.344 0.313,0.156 10 false I6 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the I11 radio and display receiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-35 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the radio receiver assembly.



Result:
Proceed to
OK
NG



OK

NG

13.CHECK VEHICLE TYPE
13.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for 12.3 Inch Display A
except 12.3 Inch Display B



A

14.CHECK FOR STEREO COMPONENT AMPLIFIER ASSEMBLY

B

15.CHECK FOR ECM
14.CHECK FOR STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
C406366C72
1.5,0.125 1.885,0.385 0.385,0.26 2.333,1.396 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.656,0.188 1.969,0.344 0.313,0.156 10 false I6 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the S22 stereo component amplifier assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-35 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.



Result:
Proceed to
OK
NG



OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

15.CHECK FOR ECM
15.CHECK FOR ECM
a.
C406366C72
1.5,0.125 1.885,0.385 0.385,0.26 2.333,1.396 2.917,1.792 2.917,1.792 3.083,1.792 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.656,0.188 1.969,0.344 0.313,0.156 10 false I6 3.146,1.677 3.417,1.906 0.271,0.229 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the B1*1, B2*2, B70*3 ECM connector.

*1: for V35A-FTS

*2: for 1GR-FE

*3: for F33A-FTV



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I6)Location & Routing

Click Connector(I6)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

I6-35 (+S) - Body ground Ignition switch ON 11 to 14 V


HINT:

If the result is as specified, there may be a short circuit in the stereo component amplifier assembly.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG