Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY › from 2021.07
RM38G0E _52 Drivetrain _101647 DRIVE SHAFT / PROPELLER SHAFT _0473033 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C458464N01
3.292,2.844 3.885,2.844 true 6.177,0.219 6.771,0.219 true 3.438,3.958 3.438,5.042 3.438,5.042 3.781,5.042 true 6.073,5.031 6.667,5.031 true 5.823,0.052 6.104,0.406 0.281,0.354 18 false 3 4.458,2.656 4.74,3.01 0.281,0.354 18 false 1 6.708,4.865 6.99,5.219 0.281,0.354 18 false 4 4.177,4.885 4.458,5.24 0.281,0.354 18 false 2 4.281,2.719 4.438,2.917 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT DRIVE SHAFT HOLE SNAP RING 43420G (Click here) - -
2 FRONT DRIVE SHAFT ASSEMBLY LH 43420 (Click here) - -
3 DIFFERENTIAL OIL - - - -
4 STEERING KNUCKLE - - - -

V100135

MP Grease
V100136

Differential oil
V103638

Do not apply lubricants to the threaded parts ● Non-reusable part

A487300N30
5.385,3.01 6.104,3.219 0.719,0.208 3.125,3.156 3.844,3.365 0.719,0.208 1.958,2.458 1.958,2.938 false 0.875,1.448 1,1.01 1,1.01 1.208,1.01 false 3.729,2.219 3.729,2.688 3.729,2.688 3.906,2.688 false 5.698,1.781 5.698,2.25 false 6.271,2.198 6.271,3.115 6.271,3.115 6.104,3.115 false 2.958,2.427 2.958,3.26 2.958,3.26 3.125,3.26 false 1.667,2.719 1.927,2.906 0.26,0.188 10 false x 2 5.573,2.292 5.865,2.625 0.292,0.333 18 false 5 3.979,2.51 4.302,2.865 0.323,0.354 18 false 6 6.375,2.052 6.969,2.26 0.594,0.208 10 false x 6 (*A) 1.875,2.979 2.104,3.167 0.229,0.188 10 false *1 3.063,2.302 3.292,2.49 0.229,0.188 10 false x 5 1.271,0.917 1.5,1.104 0.229,0.188 10 false *2 0.938,2.104 1.24,2.292 0.302,0.188 10 false x 2 3.177,3.188 3.906,3.365 0.729,0.177 8 false 29 (296, 21) 5.427,3.042 6.156,3.219 0.729,0.177 8 false 29 (296, 21) 6.375,2.26 7.135,2.469 0.76,0.208 10 false x 4 (*B *D) 6.375,2.469 7.135,2.698 0.76,0.229 10 false x 2 (*C *E)

Procedure Part Name Code
Z101186

Z101188

Z101187

5 NO. 2 ENGINE UNDER COVER ASSEMBLY 51420 - - -
6 NO. 1 ENGINE UNDER COVER ASSEMBLY 51410 - - -

*A for V35A-FTS, w/ Cover *B for V35A-FTS, w/o Cover
*C for 1GR-FE *D for F33A-FTV, w/ Cover
*E for F33A-FTV, w/o Cover - -
*1 ENGINE SIDE COVER SUB-ASSEMBLY LH *2 ENGINE SIDE COVER SUB-ASSEMBLY RH
V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43420G 1.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING

a.
C459332N01
0.417,0.063 0.698,0.417 0.281,0.354 18 false i

i.

Install a new front drive shaft hole snap ring.

NOTICE:
·

Do not damage the spline of the inboard joint.

·

The front drive shaft hole snap ring should be installed completely.





Hide 43420 2.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

a.
C458027N01
0.396,0.073 1.042,0.385 0.646,0.313 18 false i - iii

i.

Coat the splines of the inboard joint with differential oil.


ii.

Coat the snap ring of the inboard joint with MP grease.


iii.

Align the splines and tap in the front drive shaft assembly LH with a brass bar and hammer.

NOTICE:
·

Using MP grease, set the front drive shaft hole snap ring in the groove with the opening facing downwards and centered radially.

·

Do not damage the inboard joint boot, front drive shaft dust cover LH and differential side gear shaft oil seal.

·

Make sure to follow the proper handling and installation procedures. If the front drive shaft assembly LH is installed at too large an angle or slides too much, it may fall out of the groove of the tripod joint.

·

Do not tap the end of the front drive outboard joint assembly with a hammer, etc.



HINT:

Determine whether the front drive shaft assembly LH is completely tapped in by checking for changes in the tapping sound or the reaction of the brass bar.




Hide 3.ADD DIFFERENTIAL OIL

Z101186

Click here(Click here)