Home › Suspension › FRONT SUSPENSION › FRONT UPPER SUSPENSION ARM › from 2021.07
RM38G0E _53 Suspension _102028 FRONT SUSPENSION _0473050 FRONT UPPER SUSPENSION ARM A

FRONT SUSPENSION  FRONT UPPER SUSPENSION ARM  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C404170N04
1.271,0.042 3.552,1.729 2.281,1.688 3.698,0.052 5.979,1.74 2.281,1.688 2.5,0.896 2.5,1.344 2.5,1.344 2.698,1.344 true 5,1.417 5.5,1.417 true 5.542,1.271 5.833,1.604 0.292,0.333 18 false 1 3.094,1.188 3.385,1.521 0.292,0.333 18 false 2 1.375,0.073 1.688,0.271 0.313,0.198 10 false *A 1.396,0.354 1.708,0.552 0.313,0.198 10 false *B 3.823,0.073 4.135,0.271 0.313,0.198 10 false *C

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ECM 89661 - - -
2 AIR CLEANER CASE SUB-ASSEMBLY - (Click here) - -

*A for V35A-FTS *B for RH Side
*C for LH Side - -

C404171N01
1.844,1.115 2.521,1.115 true 4.417,0.427 4.583,0.24 4.583,0.24 4.906,0.24 true 4.083,0.875 4.156,1.115 4.156,1.115 4.479,1.115 true 1.51,0.99 1.885,1.281 0.375,0.292 18 false 2 0.104,0.083 0.417,0.281 0.313,0.198 10 false *A 4.521,1.01 4.833,1.208 0.313,0.198 10 false *1 4.958,0.125 5.271,0.323 0.313,0.198 10 false *2

Procedure Part Name Code
Z101186

Z101188

Z101187

2 AIR CLEANER CASE SUB-ASSEMBLY - (Click here) - -

*A for 1GR-FE (RH Side) - -
*1 VENTILATION HOSE *2 VACUUM HOSE

C404168N01
6.313,3.698 6.313,3.365 6.313,3.365 6.479,3.365 true 1.333,3.875 3.656,3.875 true 5.938,2.042 5.531,2.042 true 4.021,1.5 3.615,1.5 true 1.385,0.25 2.333,0.25 true 4.073,1.031 3.667,1.031 true 6.542,3.219 6.823,3.573 0.281,0.354 18 false 3 6.333,1.885 6.615,2.24 0.281,0.354 18 false 4 1.125,0.125 1.406,0.479 0.281,0.354 18 false 6 4.073,1.417 4.26,1.635 0.188,0.219 10 false ● 0.969,3.719 1.25,4.073 0.281,0.354 18 false 5 4.125,0.927 4.313,1.146 0.188,0.219 10 false ● 5.323,2.698 5.781,2.896 0.458,0.198 10 false x 4

Procedure Part Name Code
Z101186

Z101188

Z101187

3 FRONT WHEEL - - - -
4 FRONT SPEED SENSOR LH 89543 (Click here) - -
5 STEERING KNUCKLE - (Click here) - -
6 FRONT UPPER SUSPENSION ARM ASSEMBLY LH 48630 - - -

V103638

Do not apply lubricants to the threaded parts ● Non-reusable part

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front upper suspension arm assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Suspension, tires, etc. Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle

·

Rear television camera view adjustment (for Rear camera detection system)


Panoramic view monitor system (Click here)
Replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. have been performed. Perform headlight ECU sub-assembly LH initialization Automatic headlight beam level control system (Click here)
Wheel alignment adjustment Perform "Calibration"
·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

Electronically controlled brake system does not operate correctly


(Click here)


HINT:
·

Use the same procedure for the RH and LH sides

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89661 1.REMOVE ECM

Z101186

HINT:

Perform this procedure only when remove of the front upper suspension arm assembly LH is necessary.




Hide 2.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Z101186

HINT:

Perform this procedure only when remove of the front upper suspension arm assembly RH is necessary.




Hide 3.REMOVE FRONT WHEEL

Hide 89543 4.DISCONNECT FRONT SPEED SENSOR LH

Z101186

NOTICE:
·

Keep the tip of the front speed sensor LH and installation hole free of foreign matter.

·

Do not rotate or apply excessive force to the front speed sensor LH when removing it from the steering knuckle. Rotating or applying excessive force may result in damage to the front speed sensor LH.




a.
C455247


Hide 5.DISCONNECT STEERING KNUCKLE

a.
C453998C01
6.115,0.896 6.615,0.896 true 0.104,0.063 0.458,0.396 0.354,0.333 18 false i 3.885,0.073 4.479,0.396 0.594,0.323 18 true ii, iii 4.594,1.458 4.906,1.615 0.313,0.156 10 true *a 6.354,1.385 6.667,1.542 0.313,0.156 10 true *b 6.656,0.802 7.115,1 0.458,0.198 10 true SST
*a Hold *b Turn


i.

Support the lower arm with a jack.


ii.

Remove the clip and nut.


iii.

Using SST, disconnect the front upper ball joint from the steering knuckle.

SST
09628-62011  



Hide 48630 6.REMOVE FRONT UPPER SUSPENSION ARM ASSEMBLY LH

a.
C453999