Home › Engine / Hybrid System › F33A-FTV (FUEL) › FUEL FILTER (for Engine Room Side) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106331 F33A-FTV FUEL _0492912 FUEL FILTER(for Engine Room Side) A

F33A-FTV FUEL  FUEL FILTER(for Engine Room Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the diesel fuel filter assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Multi-terrain monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -



CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

Make sure there are no scratches or foreign objects before and after the work.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 22815A 4.REMOVE INJECTION PUMP INSULATOR

Hide 12229 5.REMOVE VENTILATION PIPE

Hide 23705 6.REMOVE NO. 5 INJECTION PIPE SUB-ASSEMBLY

Hide 17945 7.REMOVE INTERCOOLER SUPPORT BRACKET

Hide 23706 8.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 16332 9.REMOVE NO. 1 WATER OUTLET PIPE

Hide 16341 10.REMOVE WATER OUTLET GASKET

Hide 23704 11.REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

Hide 23802F 12.DISCONNECT FUEL HOSE

Hide 23901H 13.REMOVE FUEL TUBE SUB-ASSEMBLY

a.
A492393

Remove the fuel tube sub-assembly from the No. 3 fuel pipe.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23763 14.REMOVE NO. 3 NOZZLE LEAKAGE PIPE

a.
A492389

Remove the union bolt, 2 bolts and No. 3 nozzle leakage pipe from the diesel fuel filter assembly and cylinder head sub-assembly.

NOTICE:

Do not use air tools or electric tools when loosening the union bolt.



b.
A492390

Remove the gasket from the No. 3 nozzle leakage pipe.


Hide 23816 15.REMOVE NO. 4 FUEL PIPE

a.
A492391

Remove the 2 union bolts and No. 4 fuel pipe from the injection or supply pump assembly and diesel fuel filter assembly.

NOTICE:

Do not use air tools or electric tools when loosening the union bolt.



b.
A492392

Remove the 2 gaskets form the No. 4 fuel pipe.


Hide 23815D 16.REMOVE NO. 3 FUEL PIPE

a.

w/ DPF:

i.
A492396

Remove the 2 union bolts and 2 bolts, No. 3 fuel pipe from the diesel fuel filter assembly, injection or supply pump assembly and cylinder head sub-assembly.

NOTICE:

Do not use air tools or electric tools when loosening the union bolt.



ii.
A492397

Remove the 2 gaskets from the No. 3 fuel pipe.



b.

w/o DPF:

i.
A492394

Remove the 2 union bolts and No. 3 fuel pipe from the diesel fuel filter assembly and injection or supply pump assembly.

NOTICE:

Do not use air tools or electric tools when loosening the union bolt.



ii.
A492395

Remove the 2 gaskets from the No. 3 fuel pipe.



Hide 23300D 17.REMOVE DIESEL FUEL FILTER ASSEMBLY

a.
A492398

Remove the 4 bolts and diesel fuel filter assembly from the cylinder block sub-assembly.


Hide 23300D 18.INSTALL DIESEL FUEL FILTER ASSEMBLY

a.
A492398

Temporarily install the diesel fuel filter assembly to the cylinder block sub-assembly with the 4 bolts.


b.
A494323C01
0.125,0.208 0.438,0.365 0.313,0.156 10 false *A 0.177,2.552 0.49,2.708 0.313,0.156 10 false *B
*A w/ DPF
*B w/o DPF


Install 2 new gaskets to the No. 3 fuel pipe.


c.
A492392

Install 2 new gaskets to the No. 4 fuel pipe.


d.
A494331

Temporarily install the No. 3 fuel pipe and No. 4 fuel pipe to the diesel fuel filter assembly and injection or supply pump assembly with the 4 union bolts.


e.
A494333

w/ DPF:

Temporarily install the No. 3 fuel pipe to the cylinder head sub-assembly with the 2 bolts.


f.
A492398

Tighten the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


g.
A494331

Tighten the 4 union bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


h.
A494333

w/ DPF:

Tighten the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23763 19.INSTALL NO. 3 NOZZLE LEAKAGE PIPE

a.

Install a new gasket to the No. 3 nozzle leakage pipe.


b.
A492695C01
0,0 0,0 false
V100135

Bolt
V100136

Union Bolt


Install the No. 3 nozzle leakage pipe to the diesel fuel filter assembly and cylinder head sub-assembly with the union bolt and 2 bolts.

Torque:
for union bolt : 29 N*m (296 kgf*cm, 21 ft.*lbf)
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23901H 20.INSTALL FUEL TUBE SUB-ASSEMBLY

a.

Install the fuel tube sub-assembly to the No. 3 fuel pipe.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23802F 21.CONNECT FUEL HOSE

Hide 23704 22.INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY

Hide 16341 23.INSTALL WATER OUTLET GASKET

Hide 16332 24.INSTALL NO. 1 WATER OUTLET PIPE

Hide 23706 25.INSTALL NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 17945 26.INSTALL INTERCOOLER SUPPORT BRACKET

Hide 23705 27.INSTALL NO. 5 INJECTION PIPE SUB-ASSEMBLY

Hide 12229 28.INSTALL VENTILATION PIPE

Hide 22815A 29.INSTALL INJECTION PUMP INSULATOR

Hide 31.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 33. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART