Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P009300  Fuel System Leak Detected - Large Leak  P029D00  Cylinder 1 - Injector Leaking  P02A100  Cylinder 2 - Injector Leaking  P02A500  Cylinder 3 - Injector Leaking  P02A900  Cylinder 4 - Injector Leaking  P02AD00  Cylinder 5 - Injector Leaking  P02B100  Cylinder 6 - Injector Leaking  


DESCRIPTION

A fuel pressure sensor, which is built into the injector assembly, converts the fuel pressure to an electrical signal which is sent to the ECM. Based on this signal, the ECM controls the fuel supply pump assembly and maintains the fuel pressure in the common rail assembly at the target pressure.

HINT:

If the drop in the internal fuel pressure is large when injecting fuel, the ECM interprets this as a fault and stores P009300, P029D00, P02A100, P02A500, P02A900, P02AD00 and P02B100.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P009300 Fuel System Leak Detected - Large Leak While the engine is running, a large fuel pressure decrease occurs between injections (non-injection periods) or during a half-stroke of the engine.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element assembly

·

Open or short in injector assembly circuit

·

ECM


Comes on SAE Code: P0093
P029D00 Cylinder 1 - Injector Leaking When the engine speed is at 600 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element assembly

·

Open or short in injector assembly circuit

·

ECM


Comes on SAE Code: P029D
P02A100 Cylinder 2 - Injector Leaking When the engine speed is at 600 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element assembly

·

Open or short in injector assembly circuit

·

ECM


Comes on SAE Code: P02A1
P02A500 Cylinder 3 - Injector Leaking When the engine speed is at 600 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element assembly

·

Open or short in injector assembly circuit

·

ECM


Comes on SAE Code: P02A5
P02A900 Cylinder 4 - Injector Leaking When the engine speed is at 600 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element assembly

·

Open or short in injector assembly circuit

·

ECM


Comes on SAE Code: P02A9
P02AD00 Cylinder 5 - Injector Leaking When the engine speed is at 600 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element assembly

·

Open or short in injector assembly circuit

·

ECM


Comes on SAE Code: P02AD
P02B100 Cylinder 6 - Injector Leaking When the engine speed is at 600 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element assembly

·

Open or short in injector assembly circuit

·

ECM


Comes on SAE Code: P02B1

Related Data List
DTC No. Data List
P009300
P029D00
P02A100
P02A500
P02A900
P02AD00
P02B100
·

Fuel Pressure (High)

·

Target Fuel Pressure (High)

·

i-ART Learning Status History #1 to #6

·

Injector Leaking Count #1 to #6



HINT:

When DTC P009300, P029D00, P02A100, P02A500 P02A900, P02AD00 and P02B100 are set, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine / Data List / Fuel Pressure (High).


Reference:
Engine Speed Fuel Pressure (High)
Idling Approximately 25000 to 50000 kPa
3000 rpm (No engine load) Approximately 36000 to 120000 kPa


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P009300
P029D00
P02A100
P02A500
P02A900
P02AD00
P02B100
After idling for 60 seconds, run engine at 2500 rpm for 30 seconds.
Fully depress the accelerator pedal for 5 seconds, and then release it.[*A]
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm.[*B]
Repeat procedures [*A] and [*B] 5 times.

MONITOR DESCRIPTION

This DTC indicates that fuel leaks exist in high pressure areas in the common rail system. The ECM constantly monitors the internal fuel pressure of the common rail after the engine is started. The ECM stores this DTC if the drop in the internal fuel pressure is large when injecting fuel.

In the common rail system, high-pressure fuel is always supplied to the high-pressure areas including the fuel supply pump assembly, common rail assembly, injector assemblies and piping.

The ECM adjusts the timing of when the pre-stroke control valve is closed to obtain the target internal fuel pressure.

If this DTC is stored, the ECM enters fail-safe mode. In fail-safe mode, fuel supply pump assembly operation is limited. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

CAUTION / NOTICE / HINT

NOTICE:
·

Soon after starting the engine, visually check for fuel leaks in the fuel line.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR FUEL LEAKS (IN HIGH-PRESSURE AREAS)
a.

Before starting the engine, visually check for fuel leaks from the injector assembly, common rail assembly, and the fuel pipes in high-pressure areas.

OK:

No fuel leaks in high-pressure areas.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P009300) AND RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 2)

NG

REPAIR FUEL LEAK POINT

2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P009300) AND RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 2)
a.

Read the DTCs and freeze frame data.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P009300 and "P13A011, P13A015, P13A02A, P13A511, P13A515, P13A52A, P13AA11, P13AA15, P13AA2A, P13B011, P13B015, P13B02A, P13B511, P13B515, P13B52A, P13BA11, P13BA15, P13BA2A, P13E011, P13E015, P13E511 and/or P13E515" are output C
P009300 and "P033511, P033515, P03351F, P03352A and/or P033531" are output B
Except above A




A

3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)

B

C

3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)
a.

Check if the fuel level is low.

Result:
Result Proceed to
The indicator (fuel warning light) is illuminated A
The indicator (fuel warning light) is not illuminated B




A

4.ADD FLUID

B

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VALUE #1 TO #6)
4.ADD FLUID
a.

Add fuel.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.
A490878

Using the hand pump bleed the air from the fuel system. Continue pumping until the pump resistance increases.

NOTICE:
·

Hand pump pumping speed: Max. 2 strokes/sec.

·

The hand pump must be pushed with a full stroke during pumping.

·

When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.

·

If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.

·

If the hand pump resistance does not increase despite consecutively pumping 400 times or more, there may be a fuel leak between the fuel tank, fuel filter element sub-assembly and hand pump, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.

·

If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.




b.

Start the engine.

NOTICE:
·

If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.

·

Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.

·

Use a fully-charged battery.



i.

When the engine can be started, proceed to the next step.


ii.

If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

f.

Start the engine.[*A]


g.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak.[*B]


h.

Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.[*C]

Powertrain > Engine > Active Test
Tester Display
Test the Fuel Leak
50004 372 42023

i.

Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.[*D]

A192848E03
0.177,1.313 1.583,1.583 1.406,0.271 10 false Active Test Operation 6.5,2.313 6.896,2.49 0.396,0.177 10 false Time 1.677,0.969 2.042,1.167 0.365,0.198 10 false ON 1.646,1.625 2.073,1.823 0.427,0.198 10 false OFF 2.563,1.927 3.375,2.094 0.813,0.167 10 false 10 seconds 3.188,0.656 4,0.823 0.813,0.167 10 false 10 seconds 2.635,0.24 3.229,0.417 0.594,0.177 10 false 1st time 3.896,0.24 4.5,0.427 0.604,0.188 10 false 2nd time 5.198,0.24 5.792,0.406 0.594,0.167 10 false 5th time 5.99,1.865 6.75,2.083 0.76,0.219 10 false 3 minutes


j.

Read Current DTCs.

Powertrain > Engine > Trouble Codes
50001 372
i.

When no DTCs are output, the air bleeding is completed.


ii.

If any DTCs are output, proceed to the next step.



k.

Repeat steps [*A] to [*D].


l.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

m.

Start the engine and warm it up.


n.

Confirm that the shift lever is in P or N and securely apply the parking brake.


o.

Fully depress the accelerator pedal for 5 seconds, and then release it.[*E]


p.

Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm.[*F]


q.

Repeat procedures [*E] and [*F] 5 times.

A220593E70
1.656,1.844 2.042,2.021 0.385,0.177 10 false 5000 1.51,0.583 2.01,0.76 0.5,0.177 10 false 160000 5.135,2.125 5.771,2.302 0.635,0.177 10 false 3000 rpm 1.865,2.563 1.99,2.74 0.125,0.177 10 false 0 1.854,1.24 1.979,1.417 0.125,0.177 10 false 0 0.073,0.823 1.021,1.073 0.948,0.25 10 false Fuel Pressure 0.083,2.167 1.01,2.438 0.927,0.271 10 false Engine Speed 0.083,3.458 1.25,3.656 1.167,0.198 10 false Accelerator Pedal 0.948,3.083 2.115,3.281 1.167,0.198 10 false Fully Depressed 1.021,3.719 2,3.917 0.979,0.198 10 false Fully Released 2.875,4.24 3.573,4.427 0.698,0.188 10 false 5 seconds 6.448,4.135 6.854,4.323 0.406,0.188 10 false Time 3.104,2.948 3.729,3.188 0.625,0.24 10 false Step [*E] 6.208,2.948 6.813,3.188 0.604,0.24 10 false Step [*E] 4.75,2.958 5.375,3.198 0.625,0.24 10 false Step [*F] 2.104,0.573 2.375,0.76 0.271,0.188 10 false kPa 2.073,1.771 2.385,1.938 0.313,0.167 10 false rpm


r.

Read Current DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC is output A
No DTC is output B




A

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VALUE #1 TO #6)

B

DTC CAUSED BY RUNNING OUT OF FUEL

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VALUE #1 TO #6)
a.

Read the value of Injection Feedback Value #1 to #6 in the freeze frame data recorded in Procedure 2.

Result:
Result Proceed to
Injection Feedback Value for at least one cylinder is 5 mm3/st in at least 1 set of freeze frame data B
Except above A


HINT:

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Value to increase.




A

7.READ VALUE USING GTS (FUEL PRESSURE (HIGH))

B

11.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT
7.READ VALUE USING GTS (FUEL PRESSURE (HIGH))
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).

Powertrain > Engine > Data List
Tester Display
Fuel Pressure (High)
50003 372 265

c.

Start the engine.


d.

Read the value of Fuel Pressure (High) while cranking and idling the engine.

Result:
Result Proceed to
The engine cannot be started or the engine can be started but Fuel Pressure (High) is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON B
Except above A




A

8.READ VALUE USING GTS (INJECTION FEEDBACK VALUE #1 TO #6)

B

15.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
8.READ VALUE USING GTS (INJECTION FEEDBACK VALUE #1 TO #6)
a.

Start the engine and warm it up.


b.

Enter the following menus: Powertrain / Engine / Data List / Injection Feedback Value #1 to #6.

Powertrain > Engine > Data List
Tester Display
Injection Feedback Value #1
Injection Feedback Value #2
Injection Feedback Value #3
Injection Feedback Value #4
Injection Feedback Value #5
Injection Feedback Value #6
50003 372 1410,1411,1412,1413,1414,1415

c.

Read the values.

Standard:
GTS Display Engine Condition* Normal Value
Injection Feedback Value #1
Injection Feedback Value #2
Injection Feedback Value #3
Injection Feedback Value #4
Injection Feedback Value #5
Injection Feedback Value #6
Idling -4.9 mm3/st to 4.9 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 75°C (167°F) or higher and the engine should be idled for 1 minute or more.


Result:
Result Proceed to
Injection Feedback Value for at least one cylinder is more than 5 mm3/st and engine vibration is abnormally large B
Except above A


HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Value to increase.

·

The ECM controls the system so that the sum of Injection Feedback Value for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Value for a cylinder is less than -4.9 mm3/st (-4.9 mm3/st is the lowest normal value), as long as the value of Injection Feedback Value for each of the other cylinders is 4.9 mm3/st or less, the injector assemblies are not malfunctioning.





A

9.CHECK ENGINE SPEED

B

11.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT
9.CHECK ENGINE SPEED
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

While checking the tachometer, fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat procedure *1 5 times.

Result:
Result Proceed to
No problems such as sluggishness or variations in the tachometer reading A
Except above B




A

10.CHECK FREEZE FRAME DATA

B

18.READ VALUE USING GTS (ENGINE SPEED)
10.CHECK FREEZE FRAME DATA
a.

Read the value of Injector Leaking Count #1 to #6, and i-ART Learning Status History #1 to #6 in the freeze frame data recorded in Procedure 2.

Result:

If Injector Leaking Count #1 to #6 displays a value of 1 or higher, or i-ART Learning Status History #1 to #6 displays 1 or more, the injector assembly for that cylinder needs to be replaced.


NOTICE:

In order to prevent foreign matter from entering the fuel lines, do not replace the injectors at this time. Replace the injectors after performing step 16.



Result:
Proceed to
NEXT



NEXT

11.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT
11.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT
a.

Clean the fuel filter case and replace the fuel filter element assembly.

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

12.BLEED AIR FROM FUEL SYSTEM
12.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

13.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
13.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Start the engine.


b.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Fuel Pressure (High) and Target Fuel Pressure (High).

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Fuel Pressure (High)
Fuel Pressure (High)
50004 372 42023 264,265

c.

Take a snapshot with the GTS during the Active Test.


d.

Measure the difference between the target fuel pressure (Target Fuel Pressure (High)) and the actual fuel pressure (Fuel Pressure (High)) when the "Test the Fuel Leak" Active Test is performed.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DATA LIST / ACTIVE TEST

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E76
3.604,2.427 3.719,1.948 3.719,1.948 3.792,1.948 false 4.604,2.583 4.948,2.323 4.948,2.323 5.031,2.323 false 3.438,2.635 3.479,1.833 3.479,1.833 3.427,1.833 false 3.688,3.271 3.563,4.188 3.563,4.188 3.708,4.188 false 0.083,1.417 1.448,1.573 1.365,0.156 10 false Active Test Operation 0.083,0.583 1.479,0.781 1.396,0.198 10 false Engine Speed (rpm) 0.313,3.198 1.854,3.469 1.542,0.271 10 false Fuel Pressure (High) 3.802,1.865 5.74,2.031 1.938,0.167 10 false Target Fuel Pressure (High) 6.469,4.125 6.865,4.302 0.396,0.177 10 false Time 2.115,2.417 2.885,2.99 0.771,0.573 10 false Less than 10000 kPag 3,4.26 3.688,4.427 0.688,0.167 10 false 2 seconds 5.073,2.208 6.583,2.719 1.51,0.51 10 false Abnormal Fuel Pressure (High) 2.677,1.042 3.354,1.24 0.677,0.198 10 false Test Start 4.458,1.042 5.125,1.24 0.667,0.198 10 false Test Stop 5.885,1.042 6.563,1.24 0.677,0.198 10 false Test Start 2.073,1.76 3.427,2.188 1.354,0.427 10 false Normal Fuel Pressure (High) 1.646,0.271 2.021,0.438 0.375,0.167 10 false 2000 1.885,0.833 2.052,1 0.167,0.167 10 false 0 1.75,1.302 2.073,1.469 0.323,0.167 10 false ON 1.698,1.552 2.021,1.719 0.323,0.167 10 false OFF 3.771,4.125 5.969,4.677 2.198,0.552 10 false Pressure Discharge Valve Abnormal Fuel Pressure (High)

Standard:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Fuel Pressure (High)" is the target fuel pressure controlled by the ECM.

·

"Fuel Pressure (High)" is the actual fuel pressure.



Result:
Result Proceed to
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa A
Except above B




A

14.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)

B

15.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
14.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Start the engine.


b.

Enter the following menus: Powertrain / Engine / Active Test / Control the Select Cylinder Fuel Cut.

Powertrain > Engine > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 372 42026
HINT:
·

If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

16.REPLACE INJECTOR ASSEMBLY
15.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
a.

Remove the glow plug for all the cylinders.

Click hereEngine / Hybrid System>F33A-FTV (STARTING)>GLOW PLUG>REMOVAL


b.

Visually check if there is fuel on the glow plugs.

HINT:
·

If there is fuel on a glow plug, fuel may be leaking from an injector assembly.

·

After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPag (51.0 kgf/cm2, 725 psi) of the target fuel pressure while cranking the engine.

·

If there is fuel on a glow plug, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.





Result:
Proceed to
NEXT



NEXT

16.REPLACE INJECTOR ASSEMBLY
16.REPLACE INJECTOR ASSEMBLY
NOTICE:
·

Replace the injector assembly of the cylinder which displays a value of 4.9 mm3/st or higher for Injection Feedback Value #1 to #6 in step 8.

·

Replace the injector assembly determined to be the problem in step 10 and any other injector assemblies which were determined to be malfunctioning in the steps up until this point.



a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

Replace the injection pipe sub-assembly that was removed with a new one.

·

Following the repair manual, temporarily install the injection pipe and after positioning the injector, tighten the injector to the specified torque.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

17.BLEED AIR FROM FUEL SYSTEM
17.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

21.CHECK WHETHER DTC OUTPUT RECURS
18.READ VALUE USING GTS (ENGINE SPEED)
a.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211

b.

Read the value while cranking and idling the engine.

Standard:
GTS Display Engine Condition Specified Condition
Engine Speed Cranking 50 to 400 rpm
Idling with warm engine
(L4 detection switch not in L4)
550 to 650 rpm


HINT:

The value should be the same as the actual engine speed and displayed with no interruption on the GTS.



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR OUTPUT)

NG

26.REPLACE CRANKSHAFT POSITION SENSOR
19.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR OUTPUT)
a.

Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).

Powertrain > Engine > Data List
Tester Display
Fuel Pressure (High)
50003 372 265

b.

Start the engine.


c.

When the wire harness between the No. 1 injector assembly, No. 4 injector assembly and the ECM is vibrated, check whether the fuel pressure sensor value changes due to vibration or the MIL is illuminated.

A490877C01
3.188,0.406 3.042,0.417 3.042,0.417 2.552,0.844 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 0.885,0.49 1.198,0.688 0.313,0.198 10 false *1 3.271,0.344 3.583,0.542 0.313,0.198 10 false *2 5.302,0.208 5.615,0.406 0.313,0.198 10 false *3 5.5,2.177 5.813,2.375 0.313,0.198 10 false *4
*1 Engine *2 Engine Wire
*3 Wire to Wire *4 ECM
*a Vibration Method (Reference) - -



HINT:

Clear the detected DTCs.


OK:

The "Fuel Pressure (High)" value does not change as a result of vibrations and MIL does not illuminate


Result:
Result Proceed to
When the wire harness is vibrated, MIL illuminates or the "Fuel Pressure (High)"value on the Data List changes due to vibration B
Except above A



A

20.CHECK FOR INTERMITTENT PROBLEMS

B

22.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - INJECTOR ASSEMBLY)
20.CHECK FOR INTERMITTENT PROBLEMS

Result:
Proceed to
NEXT



NEXT

21.CHECK WHETHER DTC OUTPUT RECURS
21.CHECK WHETHER DTC OUTPUT RECURS
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Start the engine.


c.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


d.

Confirm that the shift lever is in neutral and securely apply the parking brake.


e.

Fully depress the accelerator pedal for 5 seconds, and then release it.[*A]


f.

Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm.[*B]


g.

Repeat procedures [*A] and [*B] 5 times.

A220593E71
1.635,1.854 2.021,2.125 0.385,0.271 10 false 5000 1.469,0.583 1.958,0.854 0.49,0.271 10 false 160000 5.135,2.115 5.781,2.417 0.646,0.302 10 false 3000 rpm 1.865,2.542 1.99,2.719 0.125,0.177 10 false 0 1.854,1.208 1.979,1.385 0.125,0.177 10 false 0 0.073,0.823 1,1.094 0.927,0.271 10 false Fuel Pressure 0.104,2.156 1.146,2.458 1.042,0.302 10 false Engine Speed 0.073,3.448 1.24,3.688 1.167,0.24 10 false Accelerator Pedal 0.948,3.083 2.031,3.313 1.083,0.229 10 false Fully Depressed 1.021,3.719 1.969,3.979 0.948,0.26 10 false Fully Released 2.917,4.219 3.667,4.458 0.75,0.24 10 false 5 seconds 6.448,4.125 6.854,4.313 0.406,0.188 10 false Time 3.104,2.958 3.865,3.198 0.76,0.24 10 false Step [*A] 6.208,2.958 6.813,3.198 0.604,0.24 10 false Step [*A] 4.75,2.958 5.458,3.188 0.708,0.229 10 false Step [*B] 2.104,0.573 2.49,0.844 0.385,0.271 10 false kPa 2.073,1.76 2.417,2.01 0.344,0.25 10 false rpm


h.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

No DTCs are output.



Result:
Proceed to
NEXT



NEXT

END

22.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - INJECTOR ASSEMBLY)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

23.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR OUTPUT)
23.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR OUTPUT)
a.

Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).

Powertrain > Engine > Data List
Tester Display
Target Fuel Pressure (High)
50003 372 264

b.

Start the engine.


c.

When the wire harness between the No. 1 injector assembly, No. 4 injector assembly and the ECM is vibrated, check whether the fuel pressure sensor value changes due to vibration or the MIL is illuminated.

A490877C01
3.188,0.406 3.042,0.417 3.042,0.417 2.552,0.844 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 0.885,0.49 1.198,0.688 0.313,0.198 10 false *1 3.271,0.344 3.583,0.542 0.313,0.198 10 false *2 5.302,0.208 5.615,0.406 0.313,0.198 10 false *3 5.5,2.177 5.813,2.375 0.313,0.198 10 false *4
*1 Engine *2 Engine Wire
*3 Wire to Wire *4 ECM
*a Vibration Method (Reference) - -



HINT:

Clear the detected DTCs.


OK:

The "Fuel Pressure (High)" value does not change as a result of vibrations and MIL does not illuminate


Result:
Result Proceed to
When the wire harness is vibrated, MIL illuminates or the "Fuel Pressure (High)"value on the Data List changes due to vibration A
Except above B



A

24.REPLACE INJECTOR ASSEMBLY

B

21.CHECK WHETHER DTC OUTPUT RECURS
24.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

Replace the injection pipe sub-assembly that was removed with a new one.

·

Following the repair manual, temporarily install the injection pipe and after positioning the injector, tighten the injector to the specified torque.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

25.BLEED AIR FROM FUEL SYSTEM
25.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

21.CHECK WHETHER DTC OUTPUT RECURS
26.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>REMOVAL

HINT:

Before replacing the crankshaft position sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
NEXT



NEXT

21.CHECK WHETHER DTC OUTPUT RECURS