The camshaft position sensor (G2 signal) consists of a magnet and MRE (Magneto-Resistive Element).
The G2 signal plate has 3 teeth on its outer circumference and is installed on the intake camshaft sub-assembly RH. When the camshaft rotates, the protrusion on the signal plate and the air gap on the MRE change, causing fluctuations in the magnetic field that generate a voltage in the MRE.
The NE signal plate has 34 teeth and is mounted on the crankshaft angle sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the camshaft angle based on the G2 signal, and detects the crankshaft angle based on the NE signal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P03402A | Camshaft Position Sensor "A" Bank 1 or Single Sensor Signal Stuck in Range | No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more. (1 trip detection logic) |
·
Camshaft position sensor
·
Intake camshaft sub-assembly RH
·
ECM |
Comes on | SAE Code: P0340 |
| P034031 | Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal | Camshaft position sensor signal is not input with an engine speed of 650 rpm or more. (1 trip detection logic) |
·
Camshaft position sensor
·
Intake camshaft sub-assembly RH
·
ECM |
Comes on | SAE Code: P0340 |
If DTC P03402A or P034031 is stored, the following symptoms may appear:
Difficulty starting
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P03402A | Crank engine for 4 seconds (STA on) |
| P034031 | Idling for 5 second or more (STA off) |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Check the engine cranking condition.
| Result | Proceed to |
|---|---|
| Cranking is OK. | A |
| Does not crank at all. | B |
A
B
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>PROBLEM SYMPTOMS TABLE
Disconnect the camshaft position sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C110)Location & Routingewd_type=routing;type=c;code=C110 |
||
| C110-3 (VC) - C110-2 (VVI-) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the camshaft position sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C110)Location & Routingewd_type=routing;type=c;code=C110 |
||
| C110-3 (VC) - C110-1 (VVI+) | Ignition switch off | No short or no open circuit |
| C110-1 (VVI+) - C110-2 (VVI-) | Ignition switch off | No short or no open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Clearance |
Check the camshaft position sensor installation.
Camshaft position sensor is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the timing rotor of the intake camshaft sub-assembly RH.
Camshaft timing rotor does not have any cracks or deformation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Start the engine and idle it for 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>F33A-FTV (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the camshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C110,C138)Location & Routingewd_type=routing;type=c,c;code=C110,C138 |
||
| C110-3 (VC) - C138-86 (VCG) | Always | Below 1 Ω |
| C110-1 (VVI+) - C138-63 (G2+) | Always | Below 1 Ω |
| C110-2 (VVI-) - C138-85 (G2-) | Always | Below 1 Ω |
| C110-3 (VC) or C138-86 (VCG) - Body ground and other terminals | Always | 10 kΩ or higher |
| C110-1 (VVI+) or C138-63 (G2+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C110-2 (VVI-) or C138-85 (G2-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT