| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | RADIATOR ASSEMBLY | 16400 | - | - | - |
| 2 | THERMOSTAT | 16331A | - | - | - |
| 3 | VACUUM PUMP ASSEMBLY | 29300 | - | - | - |
| 4 | INJECTOR ASSEMBLY | 23670 | - | - | - |
| 5 | COMMON RAIL ASSEMBLY | 23810A | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 6 | NO. 2 WATER OUTLET PIPE | 16335B | - | - | - |
| 7 | WATER OUTLET GASKET | 16341 | - | - | - |
| 8 | NO. 1 VACUUM SWITCHING VALVE ASSEMBLY | 25860 | - | - | - |
| 9 | NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY | 25706 | - | - | - |
| 10 | WATER HOSE | 16571E | - | - | - |
| 11 | NO. 4 OIL COOLER HOSE | 15776A | - | - | - |
| 12 | WATER OUTLET | 16331 | - | - | - |
| 13 | WATER OUTLET HOUSING GASKET | 16343 | - | - | - |
| 14 | TURBOCHARGER STAY | 17293 | - | - | - |
| 15 | TURBO OIL INLET GASKET | 15471 | - | - | - |
| ● | Non-reusable part | - | - |
| *A | w/ DPF | *B | w/o DPF |
| *1 | NOZZLE LEAKAGE PIPE SCREW | *2 | INJECTOR FOLLOW SCREW |
| *3 | UNION BOLT | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 28 | VANE PUMP ASSEMBLY | 44310 | - | - | - |
| 29 | FAN BRACKET SUB-ASSEMBLY | 16307A | - | - | - |
| 30 | TIMING CHAIN COVER INSULATOR | 11336B | - | - | - |
| ● | Non-reusable part | - | - |
| *1 | NO. 1 CAMSHAFT OIL FEED PIPE SUB-ASSEMBLY | *2 | NO. 2 CAMSHAFT OIL FEED PIPE SUB-ASSEMBLY |
| *3 | UNION BOLT | - | - |
| *1 | NO. 3 CAMSHAFT OIL FEED PIPE SUB-ASSEMBLY | *2 | NO. 4 CAMSHAFT OIL FEED PIPE SUB-ASSEMBLY |
| *3 | UNION BOLT | - | - |
16400 1.REMOVE RADIATOR ASSEMBLY
16331A 2.REMOVE THERMOSTAT
29300 3.REMOVE VACUUM PUMP ASSEMBLY
23670 4.REMOVE INJECTOR ASSEMBLY
23810A 5.REMOVE COMMON RAIL ASSEMBLY
16335B 6.REMOVE NO. 2 WATER OUTLET PIPE
16341 7.REMOVE WATER OUTLET GASKET
25860 8.REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY
25706 9.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
16571E 10.DISCONNECT WATER HOSE
15776A 11.DISCONNECT NO. 4 OIL COOLER HOSE
16331 12.REMOVE WATER OUTLET
16343 13.REMOVE WATER OUTLET HOUSING GASKET
17293 14.REMOVE TURBOCHARGER STAY
15471 15.REMOVE TURBO OIL INLET GASKET
23273H 16.DISCONNECT NO. 2 FUEL HOSE
23271H 17.DISCONNECT NO. 1 FUEL HOSE
23274D 18.DISCONNECT NO. 3 FUEL HOSE
23812D 19.REMOVE NO. 2 FUEL PIPE
23901H 21.REMOVE FUEL TUBE SUB-ASSEMBLY
23801N 24.REMOVE GASKET
23282D 25.DISCONNECT NO. 4 FUEL HOSE
23811K 27.REMOVE GASKET
44310 28.DISCONNECT VANE PUMP ASSEMBLY
16307A 29.REMOVE FAN BRACKET SUB-ASSEMBLY
11336B 30.REMOVE TIMING CHAIN COVER INSULATOR
23211M 31.REMOVE FUEL PIPE BRACKET
12185 32.REMOVE OIL FILLER CAP HOUSING
23881C 33.REMOVE FUEL HOSE BRACKET
12277 34.REMOVE OIL SEPARATOR HOLDER
11225 35.REMOVE CYLINDER HEAD COVER LH SILENCER
11212B 36.REMOVE CYLINDER HEAD COVER LH
16289 37.REMOVE NO. 5 WATER BY-PASS PIPE
23764A 38.REMOVE NO. 4 NOZZLE LEAKAGE PIPE
23243C 40.DISCONNECT FUEL PUMP MOTOR WIRE
11224 41.REMOVE CYLINDER HEAD COVER SILENCER
11211 42.REMOVE CYLINDER HEAD COVER RH
43.REMOVE STARAIGHT SCREW PLUG
44.SET NO. 1 CYLINDER TO TDC/COMPRESSION
| *a | Timing Mark | - | - |
Turn the crankshaft clockwise to align the timing mark (cutout) with the timing mark of the No. 2 timing chain cover insulator, and set the No. 1 cylinder to TDC/compression.
| *a | Timing Mark | *b | Paint Mark |
Check that the timing marks on each camshaft timing sprocket are at the positions shown in the illustration.
If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark is at the top (set the No. 1 piston to TDC/compression).
Place paint marks on the No. 2 chain sub-assembly.
13550 45.FIX NO. 2 CHAIN TENSIONER ASSEMBLY (for Bank 1)
Turn the crankshaft approximately 10° counterclockwise, loosen the No. 2 chain sub-assembly, insert a pin in the hole of the No. 2 chain tensioner assembly, and secure the No. 2 chain tensioner assembly.
47.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY RH AND EXHAUST CAMSHAFT SUB-ASSEMBLY RH (for Bank 1)
Lift the intake camshaft sub-assembly RH as shown in the illustration, and remove the intake camshaft sub-assembly RH.
Lift the exhaust camshaft sub-assembly RH as shown in the illustration, and remove the exhaust camshaft sub-assembly RH.
Suspend the No. 2 chain sub-assembly with a string or equivalent.
Be careful not to drop the No. 2 chain sub-assembly inside the timing chain or belt cover sub-assembly.
13529G 48.REMOVE NO. 2 CAMSHAFT TIMING SPROCKET ASSEMBLY (for Bank 1)
| *a | Hexagonal Portion | - | - |
Using SST, grip the hexagonal portion, and then secure SST and intake camshaft sub-assembly RH in a vise as shown in the illustration.
Do not damage the intake camshaft sub-assembly RH.
Never grip areas other than the hexagonal portion, as this may cause damage.
Remove the bolt and No. 2 camshaft timing sprocket assembly.
Be careful not to damage the intake camshaft sub-assembly RH and No. 2 camshaft timing sprocket assembly.
49.REMOVE CAMSHAFT TIMING SPROCKET AND PUMP DRIVE SHAFT GEAR (for Bank 1)
| *a | Hexagonal Portion | - | - |
Using SST, grip the hexagonal portion, and then secure SST and exhaust camshaft sub-assembly RH in a vise as shown in the illustration.
Do not damage the exhaust camshaft sub-assembly RH.
Never grip areas other than the hexagonal portion, as this may cause damage.
Remove the 4 bolts, camshaft timing sprocket and pump drive shaft gear.
Be careful not to damage the exhaust camshaft sub-assembly RH, camshaft timing sprocket and pump drive shaft gear.
50.FIX CHAIN TENSIONER SLIPPER LH AND NO. 3 CHAIN TENSIONER ASSEMBLY (for Bank 2)
Turn the crankshaft approximately 10° counterclockwise, loosen the No. 2 chain sub-assembly, insert a pin with the pin holes of the chain tensioner slipper LH and No. 3 chain tensioner assembly aligned, then secure the chain tensioner slipper LH and No. 3 chain tensioner assembly.
52.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY LH AND EXHAUST CAMSHAFT SUB-ASSEMBLY LH (for Bank 2)
Lift the intake camshaft sub-assembly LH as shown in the illustration, and remove the intake camshaft sub-assembly LH.
Lift the exhaust camshaft sub-assembly LH as shown in the illustration, and remove the exhaust camshaft sub-assembly LH.
Suspend the No. 2 chain sub-assembly with a string or equivalent.
Be careful not to drop the No. 2 chain sub-assembly inside the timing chain or belt cover sub-assembly.
13523G 53.REMOVE CAMSHAFT TIMING SPROCKET (for Bank 2)
| *a | Hexagonal Portion | - | - |
Using SST, grip the hexagonal portion, and then secure SST and intake camshaft sub-assembly LH in a vise as shown in the illustration.
Do not damage the intake camshaft sub-assembly LH.
Never grip areas other than the hexagonal portion, as this may cause damage.
Remove the 4 bolts and camshaft timing sprocket.
Be careful not to damage the intake camshaft sub-assembly LH and camshaft timing sprocket.
13529G 54.REMOVE NO. 2 CAMSHAFT TIMING SPROCKET ASSEMBLY (for Bank 2)
| *a | Hexagonal Portion | - | - |
Using SST, grip the hexagonal portion, and then secure SST and exhaust camshaft sub-assembly LH in a vise as shown in the illustration.
Do not damage the exhaust camshaft sub-assembly LH.
Never grip areas other than the hexagonal portion, as this may cause damage.
Remove the bolt and No. 2 camshaft timing sprocket assembly.
Be careful not to damage the exhaust camshaft sub-assembly LH and No. 2 camshaft timing sprocket assembly.