Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484891 ECD SYSTEM(w/o DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P052FA3  Glow Plug Control Module 1 System Voltage System Voltage High  P068386  Glow Plug Control Module 1 to PCM Communication Circuit Signal (some circuit quantity, reported via serial data) Invalid  P06F9A3  Glow Plug Control Module 2 System Voltage System Voltage High  P06FC86  Glow Plug Control Module 2 to PCM Communication Circuit Signal (some circuit quantity, reported via serial data) Invalid  


DESCRIPTION

The glow system consists of the glow plug controller, glow plug assemblies and ECM. The glow plug controller turns on the glow plug assembly of each cylinder according to the duty command signal from the ECM in order to maintain optimal engine temperatures. The glow plug assemblies can be controlled according to the engine coolant temperature at engine start by using duty signals. This helps induce ignition under low temperatures and prevent rough idle after starting the engine.

The glow plug controller contains a self-diagnosis function. When the glow plug controller detects an internal malfunction, it sends a signal indicating the malfunction to the ECM. When the ECM receives this signal, it illuminates the MIL and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P052FA3 Glow Plug Control Module 1 System Voltage System Voltage High The glow plug controller recognizes the battery voltage as being 39.99 V or higher 3 times or more when the glow plug assemblies are on.
(2 trip detection logic)
Glow plug controller (Bank 1) Comes on SAE Code: P052F
P068386 Glow Plug Control Module 1 to PCM Communication Circuit Signal (some circuit quantity, reported via serial data) Invalid When the glow plug assemblies are on, the ECM detects that there is no output from the glow plug control unit for 3 seconds even though the ECM outputs an SI signal ("ON" command signal).
(2 trip detection logic)
·

Open or short circuit in ground wire

·

Open or short circuit in battery wire

·

Open in SI wire

·

SI wire short circuit to ground or battery

·

Open in DI wire

·

DI wire short circuit to ground or battery

·

Low battery voltage

·

Glow plug controller (Bank 1)

·

ECM


Comes on SAE Code: P0683
P06F9A3 Glow Plug Control Module 2 System Voltage System Voltage High The glow plug controller recognizes the battery voltage as being 39.99 V or higher 3 times or more when the glow plug assemblies are on.
(2 trip detection logic)
Glow plug controller (Bank 2) Comes on SAE Code: P06F9
P06FC86 Glow Plug Control Module 2 to PCM Communication Circuit Signal (some circuit quantity, reported via serial data) Invalid When the glow plug assemblies are on, the ECM detects that there is no output from the glow plug control unit for 3 seconds even though the ECM outputs an SI signal ("ON" command signal).
(2 trip detection logic)
·

Open or short circuit in ground wire

·

Open or short circuit in battery wire

·

Open in SI wire

·

SI wire short circuit to ground or battery

·

Open in DI wire

·

DI wire short circuit to ground or battery

·

Low battery voltage

·

Glow plug controller (Bank 2)

·

ECM


Comes on SAE Code: P06FC

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P052FA3
P068386
P06F9A3
P06FC86
The engine coolant temperature is 35°C or less and the ignition switch is turned to ON.
HINT:

If the engine coolant temperature is 35°C or less, glow control will operate.



WIRING DIAGRAM

Bank 1 Side
A492042E01
1.292,0.438 1.75,0.635 0.458,0.198 10 false B74 1.281,0.938 1.74,1.135 0.458,0.198 10 false B74 1.292,1.927 1.75,2.125 0.458,0.198 10 false B73 1.292,2.417 1.75,2.615 0.458,0.198 10 false B73 1.281,2.906 1.74,3.104 0.458,0.198 10 false B72 1.281,4.813 1.74,5.01 0.458,0.198 10 false B74 1.292,3.885 1.75,4.083 0.458,0.198 10 false B74 1.271,4.344 1.729,4.542 0.458,0.198 10 false B71 1.375,0.271 1.531,0.469 0.156,0.198 10 false 3 1.375,0.75 1.531,0.948 0.156,0.198 10 false 5 1.354,1.75 1.51,1.948 0.156,0.198 10 false 1 1.354,2.219 1.51,2.417 0.156,0.198 10 false 2 1.344,2.729 1.5,2.927 0.156,0.198 10 false 1 1.365,3.688 1.521,3.885 0.156,0.198 10 false 4 1.354,4.156 1.51,4.354 0.156,0.198 10 false 1 1.365,4.646 1.521,4.844 0.156,0.198 10 false 1 3.573,4.833 3.729,5.031 0.156,0.198 10 false 5 4.313,4.813 4.469,5.01 0.156,0.198 10 false 2 4.302,5.802 4.458,6 0.156,0.198 10 false 1 3.573,5.792 3.729,5.99 0.156,0.198 10 false 3 2.344,3.385 4.385,3.677 2.042,0.292 10 false Glow Plug Connector (Bank 1) 4.5,5.302 6.031,5.5 1.531,0.198 10 false GLOW NO. 1 2.813,6.406 4.344,6.604 1.531,0.198 10 false GLOW NO. 1 3,2.938 3.458,3.135 0.458,0.198 10 false GLW3 3.01,2.448 3.469,2.646 0.458,0.198 10 false GLW2 0.885,1.948 1.344,2.146 0.458,0.198 10 false GL1 2.833,2.823 2.99,3.021 0.156,0.198 10 false 3 2.833,2.344 2.99,2.542 0.156,0.198 10 false 2 2.844,1.833 3,2.031 0.156,0.198 10 false 1 4.188,1.927 4.344,2.125 0.156,0.198 10 false 1 4.198,2.417 4.354,2.615 0.156,0.198 10 false 3 4.208,2.906 4.365,3.104 0.156,0.198 10 false 5 4.438,2.031 4.667,2.26 0.229,0.229 10 false *1 4.417,2.531 4.646,2.76 0.229,0.229 10 false *2 4.427,3.021 4.656,3.25 0.229,0.229 10 false *3 0.823,5.74 2.917,5.938 2.094,0.198 10 false *1: No. 1 Cylinder Glow Plug 0.813,6 2.896,6.208 2.083,0.208 10 false *2: No. 3 Cylinder Glow Plug 0.823,6.26 2.906,6.469 2.083,0.208 10 false *3: No. 5 Cylinder Glow Plug 3.01,1.948 3.469,2.146 0.458,0.198 10 false GLW1 0.865,2.438 1.323,2.635 0.458,0.198 10 false GL2 0.875,2.927 1.333,3.125 0.458,0.198 10 false GL3 0.969,0.458 1.427,0.656 0.458,0.198 10 false SI 0.979,0.969 1.438,1.167 0.458,0.198 10 false DI 0.854,4.833 1.313,5.031 0.458,0.198 10 false GND 0.771,4.375 1.229,4.573 0.458,0.198 10 false BATT 0.948,3.906 1.406,4.104 0.458,0.198 10 false +B 2.365,3.229 2.823,3.427 0.458,0.198 10 false C142 5.542,0.927 6,1.125 0.458,0.198 10 false B70 5.948,0.948 6.406,1.146 0.458,0.198 10 false GLDI 5.958,0.469 6.417,0.667 0.458,0.198 10 false GLDO 5.552,0.427 6.01,0.625 0.458,0.198 10 false B70 5.604,0.75 5.875,0.958 0.271,0.208 10 false 41 5.604,0.24 5.875,0.448 0.271,0.208 10 false 42 6,4.396 6.458,4.594 0.458,0.198 10 false GREL 5.563,4.156 5.833,4.365 0.271,0.208 10 false 44 5.531,4.354 5.99,4.552 0.458,0.198 10 false B70 6.156,7.073 6.667,7.427 0.51,0.354 10 false ECM 0.26,5.302 2.344,5.51 2.083,0.208 10 false Glow Plug Controller (Bank 1) 5.281,6.979 5.438,7.177 0.156,0.198 10 false B 3.677,6.99 3.833,7.188 0.156,0.198 10 false A

Bank 2 Side
A492042E03
1.292,0.427 1.75,0.625 0.458,0.198 10 false B78 1.281,0.927 1.74,1.125 0.458,0.198 10 false B78 1.292,1.927 1.75,2.125 0.458,0.198 10 false B77 1.281,2.417 1.74,2.615 0.458,0.198 10 false B77 1.281,2.906 1.74,3.104 0.458,0.198 10 false B76 1.281,4.813 1.74,5.01 0.458,0.198 10 false B78 1.292,3.885 1.75,4.083 0.458,0.198 10 false B78 1.271,4.354 1.729,4.552 0.458,0.198 10 false B75 1.375,0.271 1.531,0.469 0.156,0.198 10 false 3 1.375,0.75 1.531,0.948 0.156,0.198 10 false 5 1.354,1.75 1.51,1.948 0.156,0.198 10 false 1 1.354,2.219 1.51,2.417 0.156,0.198 10 false 2 1.344,2.729 1.5,2.927 0.156,0.198 10 false 1 1.365,3.688 1.521,3.885 0.156,0.198 10 false 4 1.354,4.156 1.51,4.354 0.156,0.198 10 false 1 1.365,4.646 1.521,4.844 0.156,0.198 10 false 1 3.573,4.833 3.729,5.031 0.156,0.198 10 false 5 4.313,4.813 4.469,5.01 0.156,0.198 10 false 2 4.302,5.802 4.458,6 0.156,0.198 10 false 1 3.573,5.792 3.729,5.99 0.156,0.198 10 false 3 2.417,3.385 5.344,3.76 2.927,0.375 10 false Glow Plug Connector (Bank 2) 4.49,5.302 6.021,5.5 1.531,0.198 10 false GLOW NO. 2 2.823,6.396 4.354,6.594 1.531,0.198 10 false GLOW NO. 2 3,2.938 3.458,3.135 0.458,0.198 10 false GLW6 3.01,2.448 3.469,2.646 0.458,0.198 10 false GLW5 0.885,1.948 1.344,2.146 0.458,0.198 10 false GL4 2.833,2.823 2.99,3.021 0.156,0.198 10 false 3 2.833,2.344 2.99,2.542 0.156,0.198 10 false 2 2.844,1.833 3,2.031 0.156,0.198 10 false 1 4.198,1.927 4.354,2.125 0.156,0.198 10 false 2 4.198,2.427 4.354,2.625 0.156,0.198 10 false 4 4.208,2.906 4.365,3.104 0.156,0.198 10 false 6 4.438,2.031 4.667,2.26 0.229,0.229 10 false *1 4.417,2.531 4.646,2.76 0.229,0.229 10 false *2 4.427,3.021 4.656,3.25 0.229,0.229 10 false *3 0.885,5.729 2.969,5.938 2.083,0.208 10 false *1: No. 2 Cylinder Glow Plug 0.906,6 2.99,6.208 2.083,0.208 10 false *2: No. 4 Cylinder Glow Plug 0.906,6.26 2.99,6.469 2.083,0.208 10 false *3: No. 6 Cylinder Glow Plug 3.01,1.948 3.469,2.146 0.458,0.198 10 false GLW4 0.865,2.438 1.323,2.635 0.458,0.198 10 false GL5 0.875,2.927 1.333,3.125 0.458,0.198 10 false GL6 0.906,0.458 1.365,0.656 0.458,0.198 10 false SI2 0.906,0.969 1.365,1.167 0.458,0.198 10 false DI2 0.781,4.833 1.24,5.031 0.458,0.198 10 false GND2 0.771,4.375 1.229,4.573 0.458,0.198 10 false BAT2 0.865,3.906 1.323,4.104 0.458,0.198 10 false +B2 2.406,3.24 2.865,3.438 0.458,0.198 10 false C143 5.542,0.917 6,1.115 0.458,0.198 10 false B70 5.948,0.948 6.406,1.146 0.458,0.198 10 false GDI2 5.958,0.469 6.417,0.667 0.458,0.198 10 false GDO2 5.552,0.427 6.01,0.625 0.458,0.198 10 false B70 5.604,0.75 5.875,0.958 0.271,0.208 10 false 39 5.604,0.24 5.875,0.448 0.271,0.208 10 false 40 6,4.396 6.458,4.594 0.458,0.198 10 false GRL2 5.563,4.156 5.833,4.365 0.271,0.208 10 false 43 5.542,4.344 6,4.542 0.458,0.198 10 false B70 6.177,7.083 6.698,7.469 0.521,0.385 10 false ECM 0.25,5.302 2.333,5.51 2.083,0.208 10 false Glow Plug Controller (Bank 2) 3.677,6.979 3.833,7.177 0.156,0.198 10 false C 5.302,6.948 5.458,7.146 0.156,0.198 10 false D

A492043E01
0.271,0.479 0.427,0.677 0.156,0.198 10 false A 3.521,0.479 3.677,0.677 0.156,0.198 10 false B 5.135,0.448 5.292,0.646 0.156,0.198 10 false D 1.917,0.51 2.073,0.708 0.156,0.198 10 false C 4.344,2.125 5.573,2.323 1.229,0.198 10 false EFI NO. 3 4.313,2.563 5.542,2.76 1.229,0.198 10 false EFI-B NO. 3 5.51,3.333 6.74,3.531 1.229,0.198 10 false 3 5.427,3.552 6.656,3.75 1.229,0.198 10 false B70 5.813,3.604 7.042,3.802 1.229,0.198 10 false MREL 2.156,3.708 3.385,3.906 1.229,0.198 10 false EFI NO. 2 2.813,3.927 4.042,4.125 1.229,0.198 10 false EFI MAIN NO. 1 0.469,3.354 1.698,3.552 1.229,0.198 10 false R/B NO. 2 1.281,3.365 1.927,3.802 0.646,0.438 10 false EFI MAIN NO. 1 0.385,4.229 1.615,4.427 1.229,0.198 10 false SUB R/B NO. 1 0.594,4.938 1.823,5.135 1.229,0.198 10 false Battery 6.219,4.385 6.698,4.875 0.479,0.49 10 false ECM 1.073,2.167 3.219,2.365 2.146,0.198 10 false EFI MAIN NO. 2 2.854,2.74 5,2.938 2.146,0.198 10 false EFI MAIN NO. 2 2.854,1.865 3.01,2.063 0.156,0.198 10 false 5 3.677,3.052 3.833,3.25 0.156,0.198 10 false 5 3.646,1.865 3.802,2.063 0.156,0.198 10 false 3 2.865,3.052 3.021,3.25 0.156,0.198 10 false 3 3.667,2.469 3.823,2.667 0.156,0.198 10 false 1 3.688,3.698 3.844,3.896 0.156,0.198 10 false 1 2.885,3.688 3.042,3.885 0.156,0.198 10 false 2 2.865,2.469 3.021,2.667 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

b.

Read the DTCs.

Result:
Result Proceed to
DTC P068386 or P06FC86 is output A
DTC P052FA3 or P06F9A3 is output B




A

2.CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT)

B

16.REPLACE GLOW PLUG CONTROLLER
2.CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT)
a.

Disconnect the glow plug controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(B74,B78)Location & Routing

Click Connector(B74)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

Click Connector(B78)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

B74-4 (+B) - Body ground Ignition switch ON 11 to 14 V
B74-4 (+B) - Body ground Ignition switch off Below 0.5 V
B78-4 (+B2) - Body ground Ignition switch ON 11 to 14 V
B78-4 (+B2) - Body ground Ignition switch off Below 0.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)

NG

9.INSPECT EFI MAIN NO. 2 RELAY
3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)
a.

Disconnect the glow plug controller connector.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)
a.

Disconnect the glow plug controller connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B74,B70,B78)Location & Routing

Click Connector(B74)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

Click Connector(B78)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

B74-3 (SI) - B70-42 (GLDO) Always Below 1 Ω
B74-5 (DI) - B70-41 (GLDI) Always Below 1 Ω
B78-3 (SI2) - B70-40 (GDO2) Always Below 1 Ω
B78-5 (DI2) - B70-39 (GDI2) Always Below 1 Ω
B74-3 (SI) or B70-42 (GLDO) - Body ground and other terminals Always 10 kΩ or higher
B74-5 (DI) or B70-41 (GLDI) - Body ground and other terminals Always 10 kΩ or higher
B78-3 (SI2) or B70-40 (GDO2) - Body ground and other terminals Always 10 kΩ or higher
B78-5 (DI2) or B70-39 (GDI2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE GLOW PLUG CONTROLLER

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE GLOW PLUG CONTROLLER
a.

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Using the GTS, check that the engine coolant temperature is 35°C or less.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
HINT:

If the engine coolant temperature is 35°C or less, glow control will operate.



d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

OK:

No DTC is output.



Result:
Proceed to
OK
NG



OK

END

NG

7.REPLACE ECM
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Using the GTS, check that the engine coolant temperature is 35°C or less.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
HINT:

If the engine coolant temperature is 35°C or less, glow control will operate.



d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

9.INSPECT EFI MAIN NO. 2 RELAY

OK

10.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - EFI MAIN NO. 2 RELAY)

NG

REPLACE EFI MAIN NO. 2 RELAY

10.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - EFI MAIN NO. 2 RELAY)
a.

Disconnect the glow plug controller connector.


b.

Remove the EFI MAIN NO. 2 relay from the No. 4 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B74,B78)Location & Routing

Click Connector(B74)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

Click Connector(B78)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>Glow Plug Controller

B74-4 (+B) - EFI MAIN NO. 2 relay terminal 3 Always Below 1 Ω
B78-4 (+B2) - EFI MAIN NO. 2 relay terminal 3 Always Below 1 Ω
B74-4 (+B) or EFI MAIN NO. 2 relay terminal 3 - Body ground and other terminals Always 10 kΩ or higher
B78-4 (+B2) or EFI MAIN NO. 2 relay terminal 3 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI MAIN NO. 2 RELAY)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI MAIN NO. 2 RELAY)
a.

Remove the EFI MAIN NO. 2 relay from the No. 4 engine room relay block and junction block assembly.


b.
A496914C02
0.115,0.063 0.427,0.26 0.313,0.198 10 false *1 2.333,0.333 2.646,0.531 0.313,0.198 10 false *2
*1 No. 4 Engine Room Relay Block and Junction Block Assembly
*2 EFI MAIN NO. 2 Relay


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
EFI MAIN NO. 2 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 2 RELAY - BODY GROUND)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
12.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI MAIN NO. 2 relay from the No. 4 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN NO. 2 relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 2 RELAY - EFI MAIN NO. 1 RELAY)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.CHECK HARNESS AND CONNECTOR (EFI MAIN NO. 2 RELAY - EFI MAIN NO. 1 RELAY)
a.

Remove the EFI MAIN NO. 2 relay from the No. 4 engine room relay block and junction block assembly.


b.

Remove the EFI MAIN NO. 1 relay from the No. 3 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN NO. 2 relay terminal 1 - EFI MAIN NO. 1 relay terminal 5 Always Below 1 Ω
EFI MAIN NO. 2 relay terminal 1 or EFI MAIN NO. 1 relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK CHARGING SYSTEM

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.CHECK CHARGING SYSTEM
a.

Check the charging system and perform repairs as necessary.

Click herePower Source / Network>F33A-FTV (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.REPLACE GLOW PLUG CONTROLLER
a.

Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for 30 seconds or more.


c.

Using the GTS, check that the engine coolant temperature is 35°C or less.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
HINT:

If the engine coolant temperature is 35°C or less, glow control will operate.



d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END