The outer mirror switch assembly sends the mirror adjust switch signals to the main body ECU (multiplex network body ECU) via LIN communication. The main body ECU (multiplex network body ECU) then sends the received mirror adjust switch signals to the outer mirror control ECU assembly (front passenger door) via CAN communication. Upon receiving the signal, the outer mirror control ECU assembly (front passenger door) operates the vertical and horizontal mirror motors, which are built into the outer rear view mirror assembly (front passenger door), to adjust the mirror surface position.
for LHD:
for RHD:
The power mirror control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system after confirming that the communication system is functioning properly.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Outer Mirror Control Switch (RH Select) | Mirror select switch signal for RH mirror | OFF or ON | OFF: Mirror select switch off ON: Mirror select switch R switch on |
- |
| Outer Mirror Control Switch (LH Select) | Mirror select switch signal for LH mirror | OFF or ON | OFF: Mirror select switch off ON: Mirror select switch L switch on |
- |
| Outer Mirror Control Switch (Surface Adjust Right) | Mirror adjust switch signal (Right) | OFF or ON | OFF: Mirror adjust switch not pushed right ON: Mirror adjust switch pushed right |
Check with the mirror select switch L or R selected |
| Outer Mirror Control Switch (Surface Adjust Left) | Mirror adjust switch signal (Left) | OFF or ON | OFF: Mirror adjust switch not pushed left ON: Mirror adjust switch pushed left |
Check with the mirror select switch L or R selected |
| Outer Mirror Control Switch (Surface Adjust Up) | Mirror adjust switch signal (Up) | OFF or ON | OFF: Mirror adjust switch not pushed up ON: Mirror adjust switch pushed up |
Check with the mirror select switch L or R selected |
| Outer Mirror Control Switch (Surface Adjust Down) | Mirror adjust switch signal (Down) | OFF or ON | OFF: Mirror adjust switch not pushed down ON: Mirror adjust switch pushed down |
Check with the mirror select switch L or R selected |
| Tester Display |
|---|
| Outer Mirror Control Switch (RH Select) |
| Outer Mirror Control Switch (LH Select) |
| Outer Mirror Control Switch (Surface Adjust Right) |
| Outer Mirror Control Switch (Surface Adjust Left) |
| Outer Mirror Control Switch (Surface Adjust Up) |
| Outer Mirror Control Switch (Surface Adjust Down) |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
OK
NG
Disconnect the N22*1 or M22*2 outer mirror switch assembly connector.
*1: for LHD
*2: for RHD
Disconnect the I1 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(N22,I1)Location & Routingewd_type=routing;type=c,c;code=N22,I1 Click Connector(N22)Body>Front Door Wire LH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=N22;pinno=4,5,7 |
||
| N22-4 (M+) - I1-22 (MIRB) | Always | Below 1 Ω |
| N22-5 (MSW) - I1-20 (MIRS) | Always | Below 1 Ω |
| N22-7 (E) - I1-21 (MIRE) | Always | Below 1 Ω |
| N22-4 (M+) or I1-22 (MIRB) - Body ground | Always | 10 kΩ or higher |
| N22-5 (MSW) or I1-20 (MIRS) - Body ground | Always | 10 kΩ or higher |
| N22-7 (E) or I1-21 (MIRE) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(M22,I1)Location & Routingewd_type=routing;type=c,c;code=M22,I1 Click Connector(M22)Body>Front Door Wire RH>Outer Mirror Switch Assemblyewd_type=component;type=c;code=M22;pinno=4,5,7 |
||
| M22-4 (M+) - I1-22 (MIRB) | Always | Below 1 Ω |
| M22-5 (MSW) - I1-20 (MIRS) | Always | Below 1 Ω |
| M22-7 (E) - I1-21 (MIRE) | Always | Below 1 Ω |
| M22-4 (M+) or I1-22 (MIRB) - Body ground | Always | 10 kΩ or higher |
| M22-5 (MSW) or I1-20 (MIRS) - Body ground | Always | 10 kΩ or higher |
| M22-7 (E) or I1-21 (MIRE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG