Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2022.11
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467519 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Communication stop for "ECM (Engine)" is indicated on the "Communication Bus Check" screen of the GTS.
(Click here)
·

ECM main wire or connector

·

Power source circuit of ECM

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

for V35A-FTS
C459008E08
0.344,1.167 2,1.729 1.656,0.563 10 false No. 7 Global CAN Junction Connector 3.427,1.115 4.844,1.354 1.417,0.24 10 false from Battery 2.563,1.542 4.292,1.813 1.729,0.271 10 false from EFI-MAIN NO.1 Relay 2.927,3.167 4.333,3.417 1.406,0.25 10 false from IGR NO.3 Relay 6.156,0.25 6.917,0.51 0.76,0.26 10 false CANH 4.458,2.906 5.448,3.125 0.99,0.219 10 false ENG-IGP NO.1 4.448,3.323 5.438,3.573 0.99,0.25 10 false ENG-IGR NO.1 6.042,5.25 6.917,5.594 0.875,0.344 10 false ECM 0.344,0.979 0.958,1.177 0.615,0.198 10 false I178 5.51,4.896 5.969,5.094 0.458,0.198 10 false B1 4.781,1.292 5.542,1.552 0.76,0.26 10 false EFI NO.2 5.885,1.115 6.646,1.375 0.76,0.26 10 false BATT 6.167,0.688 6.927,0.948 0.76,0.26 10 false CANL 5.885,1.552 6.646,1.813 0.76,0.26 10 false +B 5.875,1.948 6.635,2.208 0.76,0.26 10 false +B2 5.875,2.344 6.635,2.604 0.76,0.26 10 false MREL 5.875,2.76 6.635,3.021 0.76,0.26 10 false IGP 5.875,3.188 6.635,3.448 0.76,0.26 10 false IGR 5.885,3.573 6.646,3.833 0.76,0.26 10 false EC 5.885,4.021 6.646,4.281 0.76,0.26 10 false E1 5.865,4.875 6.625,5.135 0.76,0.26 10 false E1D1 5.875,4.438 6.635,4.698 0.76,0.26 10 false E04 1.688,0.156 2.281,0.323 0.594,0.167 10 false 2 1.688,0.594 2.406,0.771 0.719,0.177 10 false 13 5.479,0.063 5.698,0.26 0.219,0.198 10 false 18 5.5,0.5 5.719,0.698 0.219,0.198 10 false 17 5.552,0.938 5.771,1.135 0.219,0.198 10 false 1 5.521,1.344 5.74,1.542 0.219,0.198 10 false 12 5.563,2.146 5.781,2.344 0.219,0.198 10 false 3 5.531,1.75 5.75,1.948 0.219,0.198 10 false 11 5.563,2.563 5.781,2.76 0.219,0.198 10 false 8 5.552,2.969 5.771,3.167 0.219,0.198 10 false 7 5.552,3.823 5.771,4.021 0.219,0.198 10 false 9 5.521,3.396 5.74,3.594 0.219,0.198 10 false 47 5.531,4.25 5.75,4.448 0.219,0.198 10 false 54 5.531,4.667 5.75,4.865 0.219,0.198 10 false 10 2.563,2.323 4.25,2.594 1.688,0.271 10 false from EFI-MAIN NO.1 Relay 2.906,2.729 4.271,2.938 1.365,0.208 10 false from IGP NO.2 Relay 5.51,4.448 5.969,4.646 0.458,0.198 10 false B1 5.51,4.031 5.969,4.229 0.458,0.198 10 false B1 5.51,3.594 5.969,3.792 0.458,0.198 10 false B1 5.51,3.188 5.969,3.385 0.458,0.198 10 false B1 5.521,2.75 5.979,2.948 0.458,0.198 10 false B1 5.521,2.323 5.979,2.521 0.458,0.198 10 false B1 5.469,1.948 5.927,2.146 0.458,0.198 10 false C38 5.479,1.542 5.938,1.74 0.458,0.198 10 false C38 5.521,1.146 5.979,1.344 0.458,0.198 10 false B1 5.51,0.708 5.969,0.906 0.458,0.198 10 false B1 5.5,0.271 5.958,0.469 0.458,0.198 10 false B1

for 1GR-FE
C459009E03
0.344,1.156 2,1.719 1.656,0.563 10 false No. 7 Global CAN Junction Connector 3.427,1.073 4.844,1.313 1.417,0.24 10 false from Battery 2.583,1.49 4.302,1.729 1.719,0.24 10 false from EFI-MAIN NO.1 Relay 2.927,3.125 4.333,3.375 1.406,0.25 10 false from IGR NO.3 Relay 6.167,0.25 6.927,0.51 0.76,0.26 10 false CANH 4.5,2.875 5.479,3.125 0.979,0.25 10 false ENG-IGP NO.1 4.49,3.323 5.479,3.573 0.99,0.25 10 false ENG-IGR NO.1 6.042,5.198 6.917,5.542 0.875,0.344 10 false ECM 0.344,0.979 0.958,1.177 0.615,0.198 10 false I178 4.656,1.24 5.417,1.5 0.76,0.26 10 false EFI-NO.2 5.875,1.115 6.635,1.375 0.76,0.26 10 false BATT 6.177,0.667 6.938,0.927 0.76,0.26 10 false CANL 5.885,1.469 6.646,1.729 0.76,0.26 10 false +B 5.875,1.854 6.635,2.115 0.76,0.26 10 false +B2 5.875,2.302 6.635,2.563 0.76,0.26 10 false MREL 5.875,2.708 6.635,2.969 0.76,0.26 10 false IGP 5.875,3.135 6.635,3.396 0.76,0.26 10 false IGR 5.885,3.573 6.646,3.833 0.76,0.26 10 false EC 5.885,4.021 6.646,4.281 0.76,0.26 10 false E1 5.865,4.813 6.625,5.073 0.76,0.26 10 false E02 5.875,4.417 6.635,4.677 0.76,0.26 10 false E01 1.708,0.167 2.302,0.333 0.594,0.167 10 false 2 1.688,0.583 2.406,0.76 0.719,0.177 10 false 13 5.5,0.063 5.719,0.26 0.219,0.198 10 false 11 5.5,0.5 5.719,0.698 0.219,0.198 10 false 19 5.563,0.906 5.781,1.104 0.219,0.198 10 false 1 5.563,1.302 5.781,1.5 0.219,0.198 10 false 2 5.563,2.104 5.781,2.302 0.219,0.198 10 false 6 5.573,1.719 5.792,1.917 0.219,0.198 10 false 3 5.563,2.521 5.781,2.719 0.219,0.198 10 false 4 5.521,2.948 5.76,3.146 0.24,0.198 10 false 34 5.51,3.781 5.729,3.979 0.219,0.198 10 false 81 5.521,3.365 5.74,3.563 0.219,0.198 10 false 52 5.531,4.208 5.75,4.406 0.219,0.198 10 false 41 5.521,4.656 5.74,4.854 0.219,0.198 10 false 43 2.563,2.292 4.292,2.51 1.729,0.219 10 false from EFI-MAIN NO.1 Relay 2.917,2.719 4.292,2.917 1.375,0.198 10 false from IGP NO.2 Relay 5.479,4 5.938,4.198 0.458,0.198 10 false C92 5.521,2.292 5.979,2.49 0.458,0.198 10 false B2 5.51,0.688 5.969,0.885 0.458,0.198 10 false B2 5.49,0.26 5.948,0.458 0.458,0.198 10 false B2 5.51,1.094 5.969,1.292 0.458,0.198 10 false B2 5.51,1.5 5.969,1.698 0.458,0.198 10 false B2 5.51,1.906 5.969,2.104 0.458,0.198 10 false B2 5.51,2.708 5.969,2.906 0.458,0.198 10 false B2 5.51,3.135 5.969,3.333 0.458,0.198 10 false B2 5.49,3.573 5.948,3.771 0.458,0.198 10 false C92 5.49,4.396 5.948,4.594 0.458,0.198 10 false C92 5.479,4.844 5.938,5.042 0.458,0.198 10 false C92

for F33A-FTV
C470252E05
0.344,1.167 2,1.729 1.656,0.563 10 false No. 7 Global CAN Junction Connector 3.458,1.104 4.271,1.323 0.813,0.219 10 false from Battery 2.563,1.521 4.24,1.771 1.677,0.25 10 false from EFI-MAIN NO.1 Relay 2.927,3.146 4.25,3.365 1.323,0.219 10 false from IGR NO.3 Relay 6.156,0.25 6.917,0.51 0.76,0.26 10 false CANH 4.458,2.906 5.448,3.125 0.99,0.219 10 false ENG-IGP NO.1 4.448,3.323 5.438,3.573 0.99,0.25 10 false ENG-IGR NO.1 5.833,5.427 6.635,5.792 0.802,0.365 10 false ECM 0.344,0.979 0.958,1.177 0.615,0.198 10 false I178 4.781,1.292 5.542,1.552 0.76,0.26 10 false FEI NO.2 5.854,1.115 6.385,1.49 0.531,0.375 10 false BATT 6.167,0.688 6.927,0.948 0.76,0.26 10 false CANL 5.854,1.531 6.271,2.021 0.417,0.49 10 false +B 5.854,1.948 6.302,2.354 0.448,0.406 10 false +B2 5.854,2.344 6.5,2.771 0.646,0.427 10 false MREL 5.865,2.74 6.385,3.094 0.521,0.354 10 false IGP 5.865,3.167 6.313,3.531 0.448,0.365 10 false IGR 5.875,4.01 6.479,4.354 0.604,0.344 10 false E02 5.896,3.604 6.313,3.917 0.417,0.313 10 false E1 5.865,4.875 6.417,5.188 0.552,0.313 10 false E1D1 5.854,4.438 6.469,4.792 0.615,0.354 10 false E01 1.688,0.156 2.281,0.323 0.594,0.167 10 false 2 1.688,0.594 2.406,0.771 0.719,0.177 10 false 13 5.698,0.167 5.917,0.365 0.219,0.198 10 false 7 5.677,0.594 5.823,0.792 0.146,0.198 10 false 8 5.677,1.031 5.896,1.229 0.219,0.198 10 false 1 5.677,1.448 5.844,1.635 0.167,0.188 10 false 9 5.677,2.219 5.854,2.396 0.177,0.177 10 false 3 5.615,1.833 5.833,2.031 0.219,0.198 10 false 35 5.677,2.635 5.896,2.833 0.219,0.198 10 false 2 5.604,3.073 5.823,3.271 0.219,0.198 10 false 26 5.604,3.51 5.823,3.708 0.219,0.198 10 false 10 5.583,3.917 5.958,4.24 0.375,0.323 10 false 36 5.604,4.354 5.823,4.552 0.219,0.198 10 false 53 5.615,4.792 5.833,4.99 0.219,0.198 10 false 54 2.563,2.302 4.229,2.531 1.667,0.229 10 false from EFI-MAIN NO.1 Relay 2.917,2.719 4.271,2.927 1.354,0.208 10 false from IGP NO.2 Relay 0.323,4.833 2.01,5.031 1.688,0.198 10 false *1: for LHD 0.333,5.271 2.021,5.469 1.688,0.198 10 false *2: for RHD 5.813,5.24 6.281,5.5 0.469,0.26 10 false B70

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ECM MAIN WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the B1*1, B2*2 or B70*3 ECM connector.

*1: for V35A-FTS

*2: for 1GR-FE

*3: for F33A-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for V35A-FTS
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B1-18 (CANH) - B1-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 1GR-FE
Tester Connection Condition Specified Condition

Click Location & Routing(B2)Location & Routing

Click Connector(B2)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B2-11 (CANH) - B2-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for F33A-FTV
Tester Connection Condition Specified Condition

Click Location & Routing(B70)Location & Routing

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B70-7 (CANH) - B70-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect C38*1, C92*2 or B70*3 ECM connector.

*1: for V35A-FTS

*2: for 1GR-FE

*3: for F33A-FTV



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for V35A-FTS
Tester Connection Condition Specified Condition

Click Location & Routing(B1)Location & Routing

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B1-47 (EC) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
B1-9 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
B1-54 (E04) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
B1-10 (E1D1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω

for 1GR-FE
Tester Connection Condition Specified Condition

Click Location & Routing(C92)Location & Routing

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C92-52 (EC) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
C92-81 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
C92-41 (E01) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
C92-43 (E02) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω

for F33A-FTV
Tester Connection Condition Specified Condition

Click Location & Routing(B70)Location & Routing

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B70-36 (E02) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
B70-10 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
B70-53 (E01) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
B70-54 (E1D1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for V35A-FTS
Tester Connection Condition Specified Condition

Click Location & Routing(B1,C38)Location & Routing

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

Click Connector(C38)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

B1-1 (BATT) - Body ground Always 11 to 14 V
C38-12 (+B) - Body ground Terminal B1-3 (MREL) connected to body ground 11 to 14 V
C38-11 (+B2) - Body ground 11 to 14 V
B1-8 (IGP) - Body ground Ignition switch ON 11 to 14 V
B1-7 (IGR) - Body ground Ignition switch ON 11 to 14 V

for 1GR-FE
Tester Connection Condition Specified Condition

Click Location & Routing(B2)Location & Routing

Click Connector(B2)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B2-1 (BATT) - Body ground Always 11 to 14 V
B2-2 (+B) - Body ground Terminal B2-6 (MREL) connected to body ground 11 to 14 V
B2-3 (+B2) - Body ground 11 to 14 V
B2-4 (IGP) - Body ground Ignition switch ON 11 to 14 V
B2-34 (IGR) - Body ground Ignition switch ON 11 to 14 V

for F33A-FTV
Tester Connection Condition Specified Condition

Click Location & Routing(B70)Location & Routing

Click Connector(B70)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

B70-1 (BATT) - Body ground Always 11 to 14 V
B70-9 (+B) - Body ground Terminal B70-3 (MREL) connected to body ground 11 to 14 V
B70-35 (+B2) - Body ground 11 to 14 V
B70-2 (IGP) - Body ground Ignition switch ON 11 to 14 V
B70-26 (IGR) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR