| Symptom | Trouble Area |
|---|---|
|
*1: w/ Reverse Shift-linked Mirror *2: w/ Power Tilt and Power Telescopic Steering Column System *3: w/ Seat Position Memory System *4: w/ Power Back Door System |
|
| There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that store a communication stop history on the "Detail" screen. |
·
CAN bus lines or connector
·
Central gateway ECU (network gateway ECU)
·
Outer mirror control ECU assembly LH*1
·
Outer mirror control ECU assembly RH*1
·
Multiplex tilt and telescopic ECU*2
·
Position control ECU assembly*3
·
Certification ECU (smart key ECU assembly)
·
Main body ECU (multiplex network body ECU)
·
Multiplex network door ECU*4
·
No. 6 global CAN junction connector
·
No. 9 global CAN junction connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
Operating the ignition switch, any other switches or door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Disconnect the cable from the negative (-) battery terminal.
| *a | Component with harness connected (Central Gateway ECU [Network Gateway ECU]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42)Location & Routingewd_type=routing;type=c;code=I42 |
||
| I42-7 (CA5H) - I42-8 (CA5L) | Cable disconnected from negative (-) battery terminal | Below 70 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Central Gateway ECU [Network Gateway ECU]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42)Location & Routingewd_type=routing;type=c;code=I42 |
||
| I42-7 (CA5H) - I42-8 (CA5L) | Cable disconnected from negative (-) battery terminal | 54 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Central Gateway ECU [Network Gateway ECU]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42,I76)Location & Routingewd_type=routing;type=c,c;code=I42,I76 |
||
| I42-7 (CA5H) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I42-8 (CA5L) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected (Central Gateway ECU [Network Gateway ECU]) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42,I76)Location & Routingewd_type=routing;type=c,c;code=I42,I76 |
||
| I42-7 (CA5H) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-8 (CA5L) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I177 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-2 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I177-13 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-1 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I177-12 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Reverse Shift-linked Mirror | A |
| w/o Reverse Shift-linked Mirror | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-5 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I177-16 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Power Tilt and Power Telescopic Steering Column System | A |
| w/o Power Tilt and Power Telescopic Steering Column System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-4 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I177-15 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Power Back Door System | A |
| w/o Power Back Door System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-6 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I177-17 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-3 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I177-14 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I179 No. 9 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179,I76)Location & Routingewd_type=routing;type=c,c;code=I179,I76 |
||
| I179-1 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I179-12 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Reverse Shift-linked Mirror | A |
| w/o Reverse Shift-linked Mirror | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179,I76)Location & Routingewd_type=routing;type=c,c;code=I179,I76 |
||
| I179-2 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I179-13 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179,I76)Location & Routingewd_type=routing;type=c,c;code=I179,I76 |
||
| I179-4 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I179-15 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory System | A |
| w/o Seat Position Memory System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179,I76)Location & Routingewd_type=routing;type=c,c;code=I179,I76 |
||
| I179-3 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I179-14 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-1 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I177-12 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N1 outer mirror control ECU assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-5 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I177-16 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I43 multiplex tilt and telescopic ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-4 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I177-15 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T1 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-6 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I177-17 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I39 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-3 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I177-14 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M1 outer mirror control ECU assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179,I76)Location & Routingewd_type=routing;type=c,c;code=I179,I76 |
||
| I179-2 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I179-13 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I3 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179,I76)Location & Routingewd_type=routing;type=c,c;code=I179,I76 |
||
| I179-4 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I179-15 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the h24 position control ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179,I76)Location & Routingewd_type=routing;type=c,c;code=I179,I76 |
||
| I179-3 (CANH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I179-14 (CANL) - I76-4 (CG) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I177 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-2 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I177-13 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-1 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I177-12 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Reverse Shift-linked Mirror | A |
| w/o Reverse Shift-linked Mirror | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-5 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I177-16 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Power Tilt and Power Telescopic Steering Column System | A |
| w/o Power Tilt and Power Telescopic Steering Column System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-4 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I177-15 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Power Back Door System | A |
| w/o Power Back Door System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-6 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I177-17 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-3 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I177-14 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I179 No. 9 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179,I76)Location & Routingewd_type=routing;type=c,c;code=I179,I76 |
||
| I179-1 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I179-12 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Reverse Shift-linked Mirror | A |
| w/o Reverse Shift-linked Mirror | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179,I76)Location & Routingewd_type=routing;type=c,c;code=I179,I76 |
||
| I179-2 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I179-13 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179,I76)Location & Routingewd_type=routing;type=c,c;code=I179,I76 |
||
| I179-4 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I179-15 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory System | A |
| w/o Seat Position Memory System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179,I76)Location & Routingewd_type=routing;type=c,c;code=I179,I76 |
||
| I179-3 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I179-14 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-1 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I177-12 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N1 outer mirror control ECU assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-5 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I177-16 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I43 multiplex tilt and telescopic ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-4 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I177-15 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T1 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-6 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I177-17 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I39 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177,I76)Location & Routingewd_type=routing;type=c,c;code=I177,I76 |
||
| I177-3 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I177-14 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M1 outer mirror control ECU assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179,I76)Location & Routingewd_type=routing;type=c,c;code=I179,I76 |
||
| I179-2 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I179-13 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I3 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179,I76)Location & Routingewd_type=routing;type=c,c;code=I179,I76 |
||
| I179-4 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I179-15 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the h24 position control ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179,I76)Location & Routingewd_type=routing;type=c,c;code=I179,I76 |
||
| I179-3 (CANH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I179-14 (CANL) - I76-16 (BAT) | ||
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I177 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177)Location & Routingewd_type=routing;type=c;code=I177 |
||
| I177-2 (CANH) - I177-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177)Location & Routingewd_type=routing;type=c;code=I177 |
||
| I177-1 (CANH) - I177-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Reverse Shift-linked Mirror | A |
| w/o Reverse Shift-linked Mirror | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177)Location & Routingewd_type=routing;type=c;code=I177 |
||
| I177-5 (CANH) - I177-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Power Tilt and Power Telescopic Steering Column System | A |
| w/o Power Tilt and Power Telescopic Steering Column System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177)Location & Routingewd_type=routing;type=c;code=I177 |
||
| I177-4 (CANH) - I177-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Power Back Door System | A |
| w/o Power Back Door System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177)Location & Routingewd_type=routing;type=c;code=I177 |
||
| I177-6 (CANH) - I177-17 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177)Location & Routingewd_type=routing;type=c;code=I177 |
||
| I177-3 (CANH) - I177-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I179 No. 9 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179)Location & Routingewd_type=routing;type=c;code=I179 |
||
| I179-1 (CANH) - I179-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Reverse Shift-linked Mirror | A |
| w/o Reverse Shift-linked Mirror | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179)Location & Routingewd_type=routing;type=c;code=I179 |
||
| I179-2 (CANH) - I179-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179)Location & Routingewd_type=routing;type=c;code=I179 |
||
| I179-4 (CANH) - I179-15 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for vehicle type.
| Result | Proceed to |
|---|---|
| w/ Seat Position Memory System | A |
| w/o Seat Position Memory System | B |
A
B
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179)Location & Routingewd_type=routing;type=c;code=I179 |
||
| I179-3 (CANH) - I179-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177)Location & Routingewd_type=routing;type=c;code=I177 |
||
| I177-1 (CANH) - I177-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N1 outer mirror control ECU assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177)Location & Routingewd_type=routing;type=c;code=I177 |
||
| I177-5 (CANH) - I177-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I43 multiplex tilt and telescopic ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177)Location & Routingewd_type=routing;type=c;code=I177 |
||
| I177-4 (CANH) - I177-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the T1 multiplex network door ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177)Location & Routingewd_type=routing;type=c;code=I177 |
||
| I177-6 (CANH) - I177-17 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I39 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177)Location & Routingewd_type=routing;type=c;code=I177 |
||
| I177-3 (CANH) - I177-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M1 outer mirror control ECU assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179)Location & Routingewd_type=routing;type=c;code=I179 |
||
| I179-2 (CANH) - I179-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I3 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179)Location & Routingewd_type=routing;type=c;code=I179 |
||
| I179-4 (CANH) - I179-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the h24 position control ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179)Location & Routingewd_type=routing;type=c;code=I179 |
||
| I179-3 (CANH) - I179-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I177 No. 6 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177)Location & Routingewd_type=routing;type=c;code=I177 |
||
| I177-2 (CANH) - I177-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I177)Location & Routingewd_type=routing;type=c;code=I177 |
||
| I177-1 (CANH) - I177-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I177 No. 6 global CAN junction connector.
Disconnect the I179 No. 9 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179)Location & Routingewd_type=routing;type=c;code=I179 |
||
| I179-1 (CANH) - I179-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I179)Location & Routingewd_type=routing;type=c;code=I179 |
||
| I179-4 (CANH) - I179-15 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I177 No. 6 global CAN junction connector.
Disconnect the I42 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I42)Location & Routingewd_type=routing;type=c;code=I42 |
||
| I42-7 (CA5H) - I42-8 (CA5L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I179 No. 9 global CAN junction connector.
Disconnect the I3 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I3)Location & Routingewd_type=routing;type=c;code=I3 |
||
| I3-2 (CANH) - I3-1 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG