Home › Engine / Hybrid System › 1HZ (ENGINE MECHANICAL) › CYLINDER HEAD GASKET
RM25T0E _51 Engine / Hybrid System _029355 1HZ ENGINE MECHANICAL _0133478 CYLINDER HEAD GASKET A

1HZ ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


PROCEDURE

Hide 19850 4.REMOVE GLOW PLUG ASSEMBLY

Hide 11101 7.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A326343N01
3.313,4.104 3.427,4.302 0.115,0.198 10 false 1 0.271,2.917 0.406,3.094 0.135,0.177 10 false 2 3.292,2.906 3.427,3.094 0.135,0.188 10 false 3 0.281,4.083 0.417,4.26 0.135,0.177 10 false 4 2.927,2.792 3.063,2.969 0.135,0.177 10 false 5 0.719,4.26 0.854,4.438 0.135,0.177 10 false 6 2.958,4.25 3.083,4.438 0.125,0.188 10 false 7 0.604,2.813 0.76,3.01 0.156,0.198 10 false 8 2.698,4.156 2.854,4.354 0.156,0.198 10 false 9 0.917,2.865 1.125,3.083 0.208,0.219 10 false 10 2.646,2.875 2.854,3.094 0.208,0.219 10 false 11 0.917,4.146 1.125,4.365 0.208,0.219 10 false 12 2.448,2.802 2.625,2.99 0.177,0.188 10 false 13 1.125,4.26 1.302,4.448 0.177,0.188 10 false 14 2.427,4.25 2.604,4.438 0.177,0.188 10 false 15 1.135,2.792 1.313,2.979 0.177,0.188 10 false 16 2.208,4.146 2.385,4.333 0.177,0.188 10 false 17 1.354,2.875 1.531,3.063 0.177,0.188 10 false 18 2.219,2.875 2.396,3.063 0.177,0.188 10 false 19 1.354,4.146 1.531,4.333 0.177,0.188 10 false 20 2.01,2.802 2.208,3.01 0.198,0.208 10 false 21 1.573,4.26 1.771,4.469 0.198,0.208 10 false 22 2,4.26 2.198,4.469 0.198,0.208 10 false 23 1.594,2.802 1.792,3.01 0.198,0.208 10 false 24 1.792,4.146 1.99,4.354 0.198,0.208 10 false 25 1.792,2.875 1.99,3.083 0.198,0.208 10 false 26

Using 12 mm socket wrench, uniformly loosen the 26 cylinder head set bolts in the sequence shown in the illustration. Remove the 26 cylinder head set bolts and 26 plate washers.

NOTICE:
·

Be careful not to drop plate washers into the cylinder head sub-assembly.

·

Cylinder head warpage or cracking could result from removing cylinder head set bolts in an incorrect order.



HINT:

Be sure to keep separate the removed parts for each installation position.



b.
A326344C01
2.365,1.302 2.646,0.958 2.646,0.958 2.823,0.958 true 2.854,0.865 3.167,1.021 0.313,0.156 10 false *a
*a Protective Tape


Lift the cylinder head sub-assembly from the dowels on the cylinder block and place the head on wooden blocks on a bench.

NOTICE:

Be careful not to damage the cylinder head sub-assembly and cylinder block surfaces of cylinder head gasket side.


HINT:
·

If the cylinder head sub-assembly is difficult to lift off, pry with a screwdriver between the cylinder head sub-assembly and block.

·

Tape the screwdriver tip before use.




Hide 11115 8.REMOVE CYLINDER HEAD GASKET

a.
A326350

Remove the cylinder head gasket from the cylinder block.