Home › Engine / Hybrid System › 1HZ (ENGINE MECHANICAL) › CYLINDER HEAD GASKET
RM25T0E _51 Engine / Hybrid System _029355 1HZ ENGINE MECHANICAL _0133478 CYLINDER HEAD GASKET A

1HZ ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


PROCEDURE

Hide 1.CHECK PISTON PROTRUSION AND SELECT CYLINDER HEAD GASKET

a.

Check piston protrusions each cylinder.

i.

Clean the cylinder block solvent.


ii.

Set the piston of the cylinder to be measured to slightly before TDC.


iii.
A326346

Place a dial indicator on the cylinder block, and set the dial indicator at 0 mm (0 in.).

HINT:
·

Use a dial indicator measuring tip as shown in the illustration.

·

Make sure that the measuring tip is square to the cylinder block gasket surface and piston head when taking the measurements.




iv.
A329269

Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.


v.
A326347C01
1.667,2.49 1.875,2.354 1.875,2.354 2.083,2.354 false 1.677,1.906 1.885,2.094 0.208,0.188 10 false *a 2.115,2.281 2.427,2.438 0.313,0.156 10 false *b 1.969,3.698 2.281,3.854 0.313,0.156 10 false *c 0.875,0.375 1.188,0.531 0.313,0.156 10 false *d
*a X: Measuring Point
*b Measuring Tip
*c Protrusion
*d Front


Measure the protrusion of each cylinder at 2 places as shown in the illustration, making a total of 12 measurements.


vi.

For the piston protrusion value of each cylinder, use the average of the 2 measurements of each cylinder.

Standard piston protrusion:

0.405 to 0.655 mm (0.0159 to 0.0258 in.)


When removing piston and connecting rod assembly:

If the protrusion in not as specified, remove the piston and connecting rod assembly and reinstall it.

Click hereEngine / Hybrid System>1HZ (ENGINE MECHANICAL)>CYLINDER BLOCK>DISASSEMBLY



b.
A326348C01
1.51,0.24 1.823,0.396 0.313,0.156 10 false *a 0.563,1.313 0.771,1.469 0.208,0.156 10 false *b 2.854,1.927 3.01,2.125 0.156,0.198 10 false 1 1.625,3 1.781,3.198 0.156,0.198 10 false 3 3.229,3 3.385,3.198 0.156,0.198 10 false 5
*a Cutout Number
*b Front


Select new cylinder head gasket.

New Cylinder Head Gasket Thickness:
Cutout Number Thickness
1 1.15 to 1.25 mm (0.0453 to 0.0492 in.)
3 1.25 to 1.35 mm (0.0492 to 0.0531 in.)
5 1.35 to 1.45 mm (0.0531 to 0.0571 in.)


Select the largest piston protrusion value from the measurements made, then select the appropriate cylinder head gasket according to the table below.

Use Gasket Size:
Gasket Size Piston Protrusion
1 0.455 mm (0.0179 in.) or less
3 0.456 to 0.555 mm (0.0180 to 0.0219 in.)
5 0.556 mm (0.0246 in.) or more


HINT:

There are 5 types of cylinder head gasket (cutout number 1 to 5) installed at factory, but only three types for supply parts (cutout number 1, 3 and 5), so when replacing the cylinder head gasket select from one of three types above.



Hide 2.SET NO. 1 CYLINDER TO BDC

A326349

a.

Turn the crankshaft pulley, and align the BDC mark of the timing gear cover with the No. 2 camshaft timing pulley flange groove.


Hide 11115 3.INSTALL CYLINDER HEAD GASKET

a.

Place a new cylinder head gasket in position on the cylinder block.

NOTICE:
·

Be careful of the installation direction.

·

Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.




Hide 11101 4.INSTALL CYLINDER HEAD SUB-ASSEMBLY

a.

Place the cylinder head sub-assembly in position on the cylinder head gasket.

HINT:
·

The cylinder head set bolts are tightened in 3 progressive steps.

·

If any cylinder head set bolts is broken or deformed, replace it.




b.

Apply a light coat of engine oil on the threads and under the heads of the cylinder head set bolts.


c.
A326343N02
1.823,2.854 1.938,3.052 0.115,0.198 10 false 1 1.823,4.146 1.958,4.323 0.135,0.177 10 false 2 1.635,2.802 1.771,2.99 0.135,0.188 10 false 3 2.031,4.26 2.167,4.438 0.135,0.177 10 false 4 1.604,4.25 1.74,4.427 0.135,0.177 10 false 5 2.052,2.792 2.188,2.969 0.135,0.177 10 false 6 1.396,4.146 1.521,4.333 0.125,0.188 10 false 7 2.271,2.875 2.427,3.073 0.156,0.198 10 false 8 1.396,2.875 1.552,3.073 0.156,0.198 10 false 9 2.219,4.156 2.427,4.375 0.208,0.219 10 false 10 1.125,2.781 1.333,3 0.208,0.219 10 false 11 2.427,4.26 2.635,4.479 0.208,0.219 10 false 12 1.115,4.25 1.292,4.438 0.177,0.188 10 false 13 2.448,2.792 2.625,2.979 0.177,0.188 10 false 14 0.917,4.146 1.094,4.333 0.177,0.188 10 false 15 2.656,2.865 2.833,3.052 0.177,0.188 10 false 16 0.917,2.875 1.094,3.063 0.177,0.188 10 false 17 2.667,4.156 2.844,4.344 0.177,0.188 10 false 18 0.573,2.802 0.75,2.99 0.177,0.188 10 false 19 2.927,4.26 3.104,4.448 0.177,0.188 10 false 20 0.688,4.271 0.885,4.479 0.198,0.208 10 false 21 2.885,2.771 3.083,2.979 0.198,0.208 10 false 22 0.26,4.104 0.458,4.313 0.198,0.208 10 false 23 3.25,2.896 3.417,3.083 0.167,0.188 10 false 24 0.26,2.906 0.458,3.115 0.198,0.208 10 false 25 3.24,4.115 3.427,4.313 0.188,0.198 10 false 26

Step 1:

If any one of the cylinder head set bolts does not meet the torque specification, replace the cylinder head set bolt.

i.

Using 12 mm socket wrench, install and uniformly tighten the 26 plate washers and 26 cylinder head set bolts, in several passes in the sequence shown in the illustration.

Torque:
68.6 N*m (700 kgf*cm, 51 ft.*lbf)

If any one of the cylinder head set bolts does not meet the torque specification, replace the cylinder head set bolt.



d.

Step 2:

i.

Mark the front side of each cylinder head set bolt head with paint.


ii.

Tighten the cylinder head set bolts another 90°.



e.

Step 3:

i.

Tighten the cylinder head set bolts an additional 90°.


ii.

Check that the paint marks are now at a 180° angle to the front.



Hide 19850 7.INSTALL GLOW PLUG ASSEMBLY