Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2021.12
RM25T0E _51 Engine / Hybrid System _029758 1GR-FE ENGINE CONTROL _0135343 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0011  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)  P0012  Camshaft Position "A" - Timing Over-Retarded (Bank 1)  P0021  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)  P0022  Camshaft Position "A" - Timing Over-Retarded (Bank 2)  


DESCRIPTION

Refer to DTC P0010.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0010

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) Valve timing is stuck at a certain valuewhen in the advance range (1 trip detectionlogic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for bank 1)

·

Oil control valve filter

·

Camshaft timing gear assembly (for bank 1)

·

ECM


- DTC stored
P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1) Valve timing is stuck at a certain value when in the retard range (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for bank 1)

·

Oil control valve filter

·

Camshaft timing gear assembly (for bank 1)

·

ECM


- DTC stored
P0021 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2) Valve timing is stuck at a certain value when inthe advance range (1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for bank 2)

·

Oil control valve filter

·

Camshaft timing gear assembly (for bank 2)

·

ECM


- DTC stored
P0022 Camshaft Position "A" - Timing Over-Retarded (Bank 2) Valve timing is stuck at a certain value when in the retard range (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for bank 2)

·

Oil control valve filter

·

Camshaft timing gear assembly (for bank 2)

·

ECM


- DTC stored

MONITOR DESCRIPTION

The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, the camshaft timing oil control valve assembly and the VVT controller. The ECM sends a target duty-cycle control signal to the Oil Control Valve. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.

If the difference between the target and actual intake valve timings is large, and changes in the actual intake valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and stores a DTC.

Example:

A DTC is stored when conditions 1 and 2 are met:

1. It takes 5 seconds or more to change the valve timing by 5°CA.

2. After conditions 1 is met, the Oil Control Valve is forcibly activated 63 times or more (when the vehicle is idling, this takes approximately 100 seconds).



DTC P0011 and P0021 (Advanced Cam Timing) are subject to 1 trip detection logic.

DTC P0012 and P0022 (Retarded Cam Timing) are subject to 2 trip detection logic.

These DTCs indicate that the VVT controller cannot operate properly due to camshaft timing oil control valve assembly malfunctions or the presence of foreign objects in the camshaft timing oil control valve assembly.

CONFIRMATION DRIVING PATTERN

A232050E75
6.719,2.625 6.333,3.49 6.333,3.49 6.25,3.49 false 4.156,2.646 3.833,3.51 3.833,3.51 3.771,3.51 false 1.385,2.354 1.667,2.531 0.281,0.177 10 false [A] 1.875,2.021 2.26,2.271 0.385,0.25 10 false [B] 3.01,1 3.479,1.292 0.469,0.292 10 false [C] 4.052,2.313 4.417,2.542 0.365,0.229 10 false [D] 4.281,3.135 4.563,3.365 0.281,0.229 10 false [E] 5.448,2.229 5.75,2.438 0.302,0.208 10 false [F]* 6.615,2.302 6.917,2.5 0.302,0.198 10 false [G] 6.833,3.167 7.125,3.385 0.292,0.219 10 false [H] 0.135,2.313 1.104,2.646 0.969,0.333 10 false Ignition Switch ON 0.708,2.052 1.198,2.302 0.49,0.25 10 false Idling 0.177,1.094 1.135,1.438 0.958,0.344 10 false Approximately 60 km/h 0.167,0.375 1.115,0.542 0.948,0.167 10 false Vehicle Speed 1.615,2.771 2.417,2.969 0.802,0.198 10 false Warming up 2.563,2.771 3.896,2.979 1.333,0.208 10 false 10 minutes or more 2.552,3.427 3.844,3.604 1.292,0.177 10 false 3 minutes or more 2.563,0.042 7.094,0.625 4.531,0.583 10 false *: Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (depress the accelerator pedal by a large amount) and then decelerating the vehicle 10 to 15 times. 5,3.406 6.188,3.583 1.188,0.177 10 false 3 minutes or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Idle the engine for 3 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0011, P0012, P0021 or P0022.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].



14.

Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Depress the accelerator pedal by a large amount.


15.

Idle the engine for 3 minutes or more [G].

16.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [H].

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



18.

Check the DTC judgment result again.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
Abnormal Bank Advanced Timing Over
(Valve Timing is Out of Specified Range)
Retarded Timing Over
(Valve Timing is Out of Specified Range)
Bank 1 P0011 P0012
Bank 2 P0021 P0022

·

DTC P0011, P0012, P0021 or P0022 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.

·

If DTC P0011 or P0012 is output, check the right bank VVT system for the intake side circuit (for bank 1).

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

If DTC P0021 or P0022 is output, check the left bank VVT system for the intake side circuit (for bank 2).

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

d.

Read the DTCs.

Result:
Result Proceed to
DTC P0011, P0012, P0021 or P0022 is output A
DTC P0011, P0012, P0021 or P0022 and other DTCs are output B


HINT:

If any DTCs other than P0011, P0012, P0021 or P0022are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).

Powertrain > Engine and ECT > Active Test
Tester Display
Control the VVT Linear (Bank1)
50004 234 32
Powertrain > Engine and ECT > Active Test
Tester Display
Control the VVT Linear (Bank2)
50004 234 31

e.

Check the engine speed while operating the camshaft timing oil control valve assembly using the GTS.

OK:
GTS Operation Engine Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [VVT OCV Duty #1, VVT Change Angle #1, VVT OCV Duty #2 and VVT Change Angle #2] (Click here ).



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Start the engine and warm it up.


e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

g.

Read the pending DTCs.

Result:
Result Engine Condition
DTC is not output A
DTC P0011, P0012, P0021 or P0022 is output B


HINT:

DTC P0011, P0012, P0021 or P0022 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Foreign objects may then be captured by the oil control valve filter.




A

B

4.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
4.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
a.

Remove the cylinder head cover sub-assemblies RH and LH.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

A294365C01
1.625,1.021 1.792,0.344 1.792,0.344 1.625,0.802 false 2.406,1.135 2.083,1.448 2.083,1.448 2.417,0.875 false 4.917,2.135 5.031,1.313 5.031,1.313 4.927,1.802 false 5.688,2.052 5.344,2.458 5.344,2.458 5.677,1.885 false 5.354,2.448 5.646,2.042 false 1.76,0.198 2.073,0.396 0.313,0.198 10 *1 1.948,1.458 2.156,1.646 0.208,0.188 10 *1 4.99,1.156 5.302,1.354 0.313,0.198 10 *1 5.24,2.479 5.552,2.677 0.313,0.198 10 *1
*1 Timing Mark - -



b.

Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.

HINT:
·

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.

·

If the result is not as specified, check mechanical parts related to valve timing for looseness in the timing chain, jumped teeth, etc.



OK:

The timing marks on the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned as shown in the illustration.



Result:
Proceed to
OK
NG



OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

6.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

6.INSPECT OIL CONTROL VALVE FILTER
a.

Remove the oil control valve filter.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG



OK

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NG

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
a.

Replace the camshaft timing gear assembly (bank 1 or bank 2).

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Start the engine and warm it up.


e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

g.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0011, P0012, P0021 or P0022 is output B




A

END

B