In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the intake camshaft and camshaft timing oil control valve assembly, and operating the camshaft timing gear assembly; and 2) changing the relative positions of the camshaft and crankshaft.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0016 | Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) | Deviations in the crankshaft position sensor signal and VVT sensor (for bank 1) signal (2 trip detection logic). |
·
Mechanical system (Timing chain has jumped tooth or chain stretched)
·
Camshaft timing oil control valve assembly (for bank 1)
·
Oil control valve filter
·
Camshaft timing gear assembly (for bank 1)
·
ECM |
- | DTC stored |
| P0018 | Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A) | Deviations in the crankshaft position sensor signal and VVT sensor (for bank 2) signal (2 trip detection logic). |
·
Mechanical system (Timing chain has jumped tooth or chain stretched)
·
Camshaft timing oil control valve assembly (for bank 2)
·
Oil control valve filter
·
Camshaft timing gear assembly (for bank 2)
·
ECM |
- | DTC stored |
To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0016 (Bank 1) or P0018 (Bank 2).
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
Idle the engine for 5 minutes or more [C].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0016 or P0018.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL |
·
DTC judgment completed
·
System normal |
| ABNORMAL |
·
DTC judgment completed
·
System abnormal |
| INCOMPLETE |
·
DTC judgment not completed
·
Perform driving pattern after confirming DTC enabling conditions |
| N/A |
·
Unable to perform DTC judgment
·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].
Drive the vehicle for 2 to 3 minutes [E].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Idle the engine for 5 minutes or more [F].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [G].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
Refer to DTC P0335 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0335).
Refer to DTC P0340 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0340).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0016 or P0018 is output | A |
| DTC P0016 or P0018 and other DTCs are output | B |
If any DTCs other than P0016 or P0018 are output, troubleshoot those DTCs first.
A
B
If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2) / Ptrl Valve Control / VVT Change Angle #1 or VVT Change Angle #2.
| Tester Display |
|---|
| Control the VVT Linear (Bank1) |
| Tester Display |
|---|
| Control the VVT Linear (Bank2) |
Perform the Active Test. Check that the displacement angle varies.
Displacement angle varies.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the engine mechanical system.
Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the camshaft timing oil control valve assembly.
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the oil control valve filter.
Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY
Check that the filter is not clogged.
Filter is not clogged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the camshaft timing gear assembly (for bank1 or bank2).
Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
In order to clear the ECM learned values for valve timing,disconnect the cable from the negative (-) batteryterminal for 1 minute.
Connect the cable to the negative (-) battery terminal.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0016 or P0018 is output | B |
A
B