Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM J

1VD-FTV ENGINE CONTROL  ECD SYSTEM  Pre-heating Control Circuit  


DESCRIPTION

The glow plug is mounted inside the engine combustion chamber. To ensure efficient engine starting with a cold engine, the ECM calculates a time interval of the current that needs to flow through the glow plug depending on the starting engine coolant temperature when the ignition switch is turned ON. The ECM then turns on the glow plug relay and permits the current to flow through the glow plug based on the ECM's calculated time. The glow plug relay is then heated, and enhances fuel combustion with a cold engine.

This DTC will be set if the glow plug or the circuit is open.

A154593E07
0.552,1.104 1.063,1.479 0.51,0.375 10 false from Battery 0.167,0.115 2.031,0.323 1.865,0.208 10 false Glow System Wiring Diagram 1.531,0.927 2.063,1.094 0.531,0.167 10 false GLOW1 3.25,1.781 3.781,1.958 0.531,0.177 10 false GLOW1 5.229,1.198 5.708,1.375 0.479,0.177 10 false GREL 0.802,2.917 1.813,3.104 1.01,0.188 10 false No. 1 Glow Plug 5.833,2.635 6.24,2.802 0.406,0.167 10 false ECM

HINT:
·

These troubleshooting procedures are for: 1) difficult engine starting in cold weather, and 2) difficulty driving / vehicle malfunctions in cold weather immediately after engine is started.

·

After the engine is started, the ECM performs an "after-glow" for a certain period of time. In proportion to the actual engine coolant temperature, the time period varies. The after-glow reduces diesel engine knocking, white smoke emissions and engine noises when the engine is cold.



A303110E09
0.125,0.063 1.469,0.302 1.344,0.24 10 false After-glow System 1.5,0.292 2.469,0.656 0.969,0.365 10 false After-glow Time (Second) 2.51,0.573 2.792,0.781 0.281,0.208 10 false 120 2.656,1.271 2.802,1.448 0.146,0.177 10 false 1 2.708,1.458 2.854,1.635 0.146,0.177 10 false 0 3.135,1.458 3.333,1.667 0.198,0.208 10 false 30 4.094,1.458 4.292,1.667 0.198,0.208 10 false 40 4.708,1.406 4.906,1.615 0.198,0.208 10 false °C 4.719,1.552 5.063,1.792 0.344,0.24 10 false (°F) 4.031,1.594 4.427,1.854 0.396,0.26 10 false (104) 3.104,1.594 3.396,1.844 0.292,0.25 10 false (86) 2.792,1.844 4.719,2.052 1.927,0.208 10 false Engine Coolant Temperature 1.271,2.552 2.292,2.771 1.021,0.219 10 false Ignition Switch 1.521,3.333 2.229,3.552 0.708,0.219 10 false Glow Plug 1.323,4.135 2.26,4.344 0.938,0.208 10 false Engine Speed 2.427,2.469 2.729,2.698 0.302,0.229 10 false OFF 2.448,3.26 2.75,3.49 0.302,0.229 10 false OFF 4.396,2.083 4.698,2.313 0.302,0.229 10 false ON 4.438,2.865 4.74,3.094 0.302,0.229 10 false ON 5.854,3.26 6.156,3.49 0.302,0.229 10 false OFF 4.229,4.177 5.198,4.385 0.969,0.208 10 false After-glow Time 2.813,4.563 3.854,4.802 1.042,0.24 10 false Starting Engine

WIRING DIAGRAM

A335944E01
6.281,7.083 6.646,7.271 0.365,0.188 10 false C39 6.271,7.271 6.677,7.458 0.406,0.188 10 false ECM 5.854,4.552 6.073,4.729 0.219,0.177 10 false 62 6.146,4.406 6.552,4.594 0.406,0.188 10 false GRL2 6.146,0.979 6.573,1.167 0.427,0.188 10 false GREL 5.854,1.135 6.073,1.313 0.219,0.177 10 false 63 4.771,1.656 5.302,1.844 0.531,0.188 10 false GLOW1 4.781,5.083 5.313,5.271 0.531,0.188 10 false GLOW2 2.271,3.052 2.552,3.24 0.281,0.188 10 false C45 2.271,6.469 2.552,6.656 0.281,0.188 10 false C62 2.271,3.25 2.99,3.615 0.719,0.365 10 false No. 1 Glow Plug 2.281,6.656 3,7.021 0.719,0.365 10 false No. 2 Glow Plug 0.865,1.188 1.396,1.375 0.531,0.188 10 false GLOW1 0.865,4.625 1.406,4.813 0.542,0.188 10 false GLOW2 0.667,5.917 1.25,6.104 0.583,0.188 10 false FL MAIN 0.833,6.781 1.365,6.979 0.531,0.198 10 false Battery 4.583,1.219 4.802,1.396 0.219,0.177 10 false 1 4.583,4.635 4.802,4.813 0.219,0.177 10 false 1 4.594,2.063 4.813,2.24 0.219,0.177 10 false 2 4.604,5.5 4.823,5.677 0.219,0.177 10 false 2 3.813,1.219 4.031,1.396 0.219,0.177 10 false 5 3.792,2.063 4.01,2.24 0.219,0.177 10 false 3 4.042,2.51 4.26,2.688 0.219,0.177 10 false 1 3.781,5.5 4,5.677 0.219,0.177 10 false 3 3.813,4.646 4.031,4.823 0.219,0.177 10 false 5 4.042,5.948 4.26,6.125 0.219,0.177 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK ECM TERMINAL VOLTAGE (GREL TERMINAL)
a.
A225237C01
0.115,0.052 0.656,0.271 0.542,0.219 10 false *1 0.521,1.552 0.906,1.781 0.385,0.229 10 false *2 0.5,2.896 0.885,3.156 0.385,0.26 10 false *3
*1 engine room relay block assembly
*2 GLOW 1
*3 GLOW 2


Remove the GLOW1 and GLOW2 relay from the engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
GLOW 1 relay holder 1 - Body ground Ignition switch ON 11 to 14 V
GLOW 2 relay holder 1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT GLOW RELAY (NO. 1 OR NO. 2)

NG

6.CHECK HARNESS AND CONNECTOR (GLOW RELAY - ECM AND BODY GROUND)
2.INSPECT GLOW RELAY (NO. 1 OR NO. 2)

Result:
Proceed to
OK
NG



OK

3.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

NG

REPLACE GLOW RELAY (NO. 1 OR NO. 2)

3.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)
a.
A163041C01
1.354,2.927 1.677,3.083 false 1.677,2.896 1.719,2.896 false 1.781,3.052 2.135,3.229 0.354,0.177 10 true *1
*1 Screw Grommet


Disconnect the glow plug connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Glow plug terminal - Body ground 20°C (68°F) Approximately 1 Ω


HINT:

If any of the glow plugs has an open circuit, the engine power will be insufficient only when the engine is cold.


NOTICE:
·

Exercise extreme care not to damage the glow plug pipes. Damaging them could cause an open circuit, or shorten the life of the glow plugs.

·

Keep the glow plugs free of oil and fuel while cleaning.

·

Wipe any oil off of the terminal and Bakelite washer with a clean, dry cloth during inspection.

·

Do not apply more than 11 V to the glow plugs as it may cause an open circuit.




c.

Reconnect the glow plug connector.


Result:
Proceed to
OK
NG



OK

4.CHECK GLOW PLUG ASSEMBLY (INSTALLATION)

NG

4.CHECK GLOW PLUG ASSEMBLY (INSTALLATION)
a.

Check the glow plug installation.

Click hereEngine / Hybrid System>1VD-FTV (STARTING)>GLOW PLUG>INSTALLATION

OK:

Glow plugs are installed securely.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GLOW RELAY - GLOW PLUG - BATTERY AND BODY GROUND)

NG

TIGHTEN GLOW PLUG

5.CHECK HARNESS AND CONNECTOR (GLOW RELAY - GLOW PLUG - BATTERY AND BODY GROUND)
a.

Remove the GLOW1 and GLOW2 relay from the engine room R/B assembly.


b.

Disconnect the C45 and C62 glow plug connector.


c.

Disconnect the cable from the negative (-) battery terminal.


d.

Disconnect the cable from the positive (+) battery terminal.


e.

Measure the resistance according to the value(s) in the table below.

Standard resistance No. 1:
Tester Connection Condition Specified Condition
GLOW 1 relay holder 3 - C45-1 Always Below 1 Ω
GLOW 1 relay holder 5 - Positive (+) battery terminal cable Always Below 1 Ω
GLOW 1 relay holder 2 - Body ground Always Below 1 Ω


Standard resistance No. 2:
Tester Connection Condition Specified Condition
GLOW 2 relay holder 3 - C62-1 Always Below 1 Ω
GLOW 2 relay holder 5 - Positive (+) battery terminal cable Always Below 1 Ω
GLOW 2 relay holder 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (GLOW RELAY - ECM AND BODY GROUND)
a.

Remove the GLOW1 and GLOW2 relay from the engine room R/B assembly.


b.

Disconnect the C39 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
GLOW 1 relay holder 1 - C39-63 (GREL) Always Below 1 Ω
GLOW 2 relay holder 1 - C39-62 (GRL2) Always Below 1 Ω
GLOW 1 relay holder 1 or C39-63 (GREL) - Body ground Always 10 kΩ or higher
GLOW 2 relay holder 1 or C39-62 (GRL2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR