Refer to the System Description.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0088 | Fuel Rail / System Pressure - Too High | Fuel pressure of common rail is too high: Fuel pressure exceeds 250000 kPa (2549 kgf/cm2, 36250 psi) (1 trip detection logic) |
·
Fuel supply pump (suction control valve)
·
Open or short in fuel supply pump (suction control valve) circuit
·
Fuel pressure sensor (common rail assembly (for bank 1))
·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0088 |
·
Common Rail Pressure
·
Target Common Rail Pressure
·
Target Pump SCV Current |
For more information on the fuel supply pump (suction control valve) and common rail system, refer to the system description.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION
When DTC P0088 is stored, check the internal fuel pressure of the common rail assembly by entering the following menus: Engine and ECT / Data List / Common Rail Pressure.
| Engine Speed | Common Rail Pressure |
|---|---|
| Idling | Approximately 27000 to 45000 kPa |
| 3000 rpm (No engine load) | Approximately 55000 to 75000 kPa |
Check "Common Rail Pressure", "Target Common Rail Pressure" and "Target Pump SCV Current" in the freeze frame data.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0088 | After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds |
The ECM stores this DTC if the fuel pressure inside the common rail assembly is higher than 250000 kPa (2549 kgf/cm2, 36250 psi). This DTC indicates that: 1) the suction control valve may be stuck open, or 2) there may be a short in the suction control valve circuit.
If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the fuel supply pump, the ECM needs initialization.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION
After replacing an fuel injector, the ECM needs registration.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0088 is output | A |
| P0088 and "P0190, P0192 or P0193" are output | B |
When there is an open circuit in the fuel pressure sensor circuit, the fuel pressure sensor outputs the maximum value. Therefore, P0088 may be stored together with DTCs which indicate common rail fuel pressure sensor circuit malfunctions.
A
B
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Trouble Codes.
Record the stored DTCs and freeze frame data.
| Result | Proceed to |
|---|---|
| Value of Common Rail Pressure is shifting towards 160000 kPa or higher in 3rd and 4th set of freeze frame data | A |
| Except above | B |
B
A
Replace the fuel supply pump.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP (w/ DPF)>REMOVAL
Before replacing the fuel supply pump assembly, check that the wire harness between the suction control valve and ECM is not shorted to ground.
When there is a malfunction in the wire harness, Target Pump SCV Current is outside the range of 800 to 1207 mA when idling, and outside the range of 840 to 1257 mA when the engine is running at 2500 rpm without load. If there are no problems with the engine condition during idling, it is not necessary to perform the above wire harness inspection.
When the wire harness between the suction control valve and ECM is not shorted to ground, it can be assumed that DTC P0088 was stored due to a malfunction in the operation of the suction control valve. Therefore, it is necessary to replace the fuel supply pump.
| Proceed to |
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION
Perform PM forced regeneration.
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.
| Proceed to |
| NEXT |
NEXT
Perform supply pump initialization.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION
| Proceed to |
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and start the engine.
After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P0088.
Check the DTC judgment result.
| GTS Display | Result | Proceed to |
|---|---|---|
| Pending DTC | P0088 is output | A |
| All Readiness | NORMAL | B |
| ABNORMAL | A |
If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and start the engine.
After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P0088.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.
| Proceed to |
| NEXT |
NEXT
If the MIL has illuminated before in the past, clear the DTC using the GTS before performing this inspection.
| *1 | Engine | *2 | Engine Wire |
| *3 | Common Rail Assembly (for Bank 1) (Fuel Pressure Sensor) |
*4 | Wire to Wire |
| *5 | ECM | - | - |
| *a | Vibration Method (Reference) | - | - |
Check if the MIL lights up when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.
| Result | Proceed to |
|---|---|
| MIL does not come on | A |
| MIL comes on | B |
A
B
Repair or replace the harness or connector.
| Proceed to |
| NEXT |
NEXT
If the MIL has illuminated before in the past, clear the DTC using the GTS before performing this inspection.
| *1 | Engine | *2 | Engine Wire |
| *3 | Common Rail Assembly (for Bank 1) (Fuel Pressure Sensor) |
*4 | Wire to Wire |
| *5 | ECM | - | - |
| *7 | Vibration Method (Reference) | - | - |
Check if the MIL lights up when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.
| Result | Proceed to |
|---|---|
| MIL does not come on | A |
| MIL comes on | B |
A
B
Replace the common rail assembly (for bank 1).
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL (w/ DPF)>REMOVAL
| Proceed to |
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION
Perform PM forced regeneration.
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.
| Proceed to |
| NEXT |
NEXT