Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0301  Cylinder 1 Misfire Detected  P0302  Cylinder 2 Misfire Detected  P0303  Cylinder 3 Misfire Detected  P0304  Cylinder 4 Misfire Detected  P0305  Cylinder 5 Misfire Detected  P0306  Cylinder 6 Misfire Detected  P0307  Cylinder 7 Misfire Detected  P0308  Cylinder 8 Misfire Detected  


DESCRIPTION

HINT:

For more information on the fuel injectors and common rail system, refer to System Description.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION

The ECM detects combustion deterioration for a specific cylinder.


A113716C02
3.542,1.448 2.938,1.24 true 3.573,2.021 4.188,1.813 true 3.573,2.688 4.188,2.469 true 3.563,2.24 2.958,2.031 true 3.583,3.458 2.979,3.24 true 0.229,0.167 0.49,0.344 0.26,0.177 10 false *a 2.74,1.167 2.896,1.333 0.156,0.167 10 false *1 4.24,2.396 4.406,2.563 0.167,0.167 10 false *4 2.813,3.156 2.979,3.323 0.167,0.167 10 false *5 4.229,1.74 4.396,1.906 0.167,0.167 10 false *2 2.75,1.948 2.917,2.115 0.167,0.167 10 false *3
*1 Piezo Actuator *2 No. 1 Piston
*3 No. 2 Piston *4 Three-way Valve
*5 Nozzle Needle - -
*a Fuel Injector Cross Section Diagram - -


HINT:
·

The cylinder which has the compensation value, indicated by Injection Feedback Val #1 to #8, that varies from the other cylinders may be malfunctioning.

·

If DTC P0093 (fuel leaks from high-pressure area) is stored simultaneously, a leakage malfunction of a specific cylinder has probably occurred.

·

If any of the DTCs from P0201 to P0208, P062D or P062E (open or short in the injector driver or injector circuit) is stored simultaneously, there is probably a faulty circuit located between the ECM and the fuel injector including the injector driver.

·

If only DTC from P0301 to P0308 (injector malfunction) has been stored, an fuel injector mechanical malfunction or insufficient compression (valve clearance, etc.) has probably occurred. An open or short malfunction of the ECM, injector driver or injector circuit is unlikely.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0301 Cylinder 1 Misfire Detected Injector Feedback Val #1 is 5.0 mm3/st and the engine speed fluctuation of No. 1 cylinder is large during idling.
·

No. 1 fuel injector

·

Compression pressure


Comes on DTC stored
P0302 Cylinder 2 Misfire Detected Injector Feedback Val #2 is 5.0 mm3/st and the engine speed fluctuation of No. 2 cylinder is large during idling.
·

No. 2 fuel injector

·

Compression pressure


Comes on DTC stored
P0303 Cylinder 3 Misfire Detected Injector Feedback Val #3 is 5.0 mm3/st and the engine speed fluctuation of No. 3 cylinder is large during idling.
·

No. 3 fuel injector

·

Compression pressure


Comes on DTC stored
P0304 Cylinder 4 Misfire Detected Injector Feedback Val #4 is 5.0 mm3/st and the engine speed fluctuation of No. 4 cylinder is large during idling.
·

No. 4 fuel injector

·

Compression pressure


Comes on DTC stored
P0305 Cylinder 5 Misfire Detected Injector Feedback Val #5 is 5.0 mm3/st and the engine speed fluctuation of No. 5 cylinder is large during idling.
·

No. 5 fuel injector

·

Compression pressure


Comes on DTC stored
P0306 Cylinder 6 Misfire Detected Injector Feedback Val #6 is 5.0 mm3/st and the engine speed fluctuation of No. 6 cylinder is large during idling.
·

No. 6 fuel injector

·

Compression pressure


Comes on DTC stored
P0307 Cylinder 7 Misfire Detected Injector Feedback Val #7 is 5.0 mm3/st and the engine speed fluctuation of No. 7 cylinder is large during idling.
·

No. 7 fuel injector

·

Compression pressure


Comes on DTC stored
P0308 Cylinder 8 Misfire Detected Injector Feedback Val #8 is 5.0 mm3/st and the engine speed fluctuation of No. 8 cylinder is large during idling.
·

No. 8 fuel injector

·

Compression pressure


Comes on DTC stored

Related Data List
DTC No. Data List
P0301 to P0308
·

Injection Volume

·

Injection Feedback Val #1 to #8

·

Common Rail Pressure

·

Target Common Rail Pressure



HINT:
·

If any of DTCs from P0301 to P0308 is stored, the following symptoms may appear:

-

Rough idle

-

Poor driveability


·

After confirming DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308, check the internal fuel pressure on the GTS by entering the following menus: Engine and ECT / Data List / Common Rail Pressure, Target Common Rail Pressure.

Under a stable condition such as idling or running the engine at 2500 rpm without load, Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure.



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0301
P0302
P0303
P0304
P0305
P0306
P0307
P0308
Warm up the engine and idle it for 60 seconds

MONITOR DESCRIPTION

P0301 to P0308 (Injection malfunction, except open or short in injector circuit):

This DTC will be stored if the engine speed fluctuation between each cylinder is large. The ECM monitors changes in the crankshaft rotation speed using the crankshaft position sensor in order to detect improper combustion. The camshaft position sensor also plays a role in determining which cylinder has the problem. The fluctuation counter increases when irregular crankshaft rotation speed variation exceeds the threshold with the engine idling. Therefore, if any one of the cylinders is operating poorly (rough idle), the ECM stores this DTC.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION

·

After replacing an fuel injector, the ECM needs registration.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When this DTC is stored, be sure to carefully examine "Injection Feedback Val #1 to #8", "Injection Volume", "Common Rail Pressure", "Target Common Rail Pressure", "Engine Speed", "MAF", "Coolant Temp" and "Vehicle Speed" in the freeze frame data.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307 OR P0308)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

d.

Read the DTCs.

Standard value:

The compensatory injection volume is less than 3.0 mm3/st



Result:
Proceed to Proceed to
P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 is output A
P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 and other DTCs are output B


HINT:
·

If any DTCs other than P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 are output, troubleshoot those DTCs first.

·

If DTCs other than P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 are not output, check the fuel condition before proceeding to the next step.




A

2.CHECK HARNESS AND CONNECTOR (ENGINE WIRE HARNESS)

B

2.CHECK HARNESS AND CONNECTOR (ENGINE WIRE HARNESS)
a.

Check the wire harness and connector connections.

OK:

The wire harness and connectors have been connected securely and there are good connections.



Result:
Proceed to
OK
NG



OK

3.CHECK INJECTOR COMPENSATION CODE

NG

14.REPAIR OR REPLACE HARNESS AND CONNECTOR
3.CHECK INJECTOR COMPENSATION CODE

OK:

Compensation codes stored in the ECM match compensation codes of the installed injector assemblies.


Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (COMPENSATORY INJECTION VOLUME FOR EACH CYLINDER)

NG

9.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
4.READ VALUE USING GTS (COMPENSATORY INJECTION VOLUME FOR EACH CYLINDER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Data List / Injection Feedback Val #1 to #8.

Powertrain > Engine and ECT > Data List
Tester Display
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection Feedback Val #5
Injection Feedback Val #6
Injection Feedback Val #7
Injection Feedback Val #8
50003 234 778,779,780,781,782,783,784,785

d.

Read the value.

Standard value:

The compensatory injection volume is less than 3.0 mm3/st


HINT:
·

If the fuel injector is malfunctioning, the compensatory injection volume remains at 5.0 mm3/ st.

·

If there is a disconnection, the feedback value will increase and +5.0 mm3/st will be indicated, because it will become impossible for the fuel injector to inject.




e.

Inspect and repair the cylinder that has an improper compensation value according to the following steps.


Result:
Proceed to
NEXT



NEXT

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
5.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut / #1 to #8.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 234 235

d.

Check the 8 cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.


HINT:
·

If the engine idle speed does not change when an fuel injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.



Result:
Proceed to
NEXT



NEXT

6.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
6.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.


a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

7.REPLACE FUEL INJECTOR

NG

13.CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
7.REPLACE FUEL INJECTOR
a.

Replace the fuel injector.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/ DPF)>REMOVAL

NOTICE:
·

When replacing the fuel injector for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an fuel injector deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an fuel injector becomes out of position, it is possible that the seal between the fuel injector and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM

b.

Perform PM forced regeneration.

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.



Result:
Proceed to
NEXT



NEXT

9.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
9.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION


Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307 OR P0308)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307 OR P0308)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine.


f.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

h.

Read the pending DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.


iii.

Check the DTC judgment result.



Result:
GTS Display Result Proceed to
Pending DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 is output A
All Readiness ABNORMAL A
NORMAL B


HINT:

If STATUS is INCOMPLETE or N/A, increase the idling time.



A

11.REPLACE ECM

B

END

11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

ii.

Input DTC P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.



Result:
Proceed to
NEXT



NEXT

END

13.CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
Result:
Proceed to
NEXT



NEXT

13.CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
14.REPAIR OR REPLACE HARNESS AND CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION