Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2016.08
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System)  C1413  Front Speed Sensor RH Output Malfunction  C1414  Front Speed Sensor LH Output Malfunction  


DESCRIPTION

Refer to DTCs C1401 and C1402.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>C1401

DTC No. Detection Item DTC Detection Condition Trouble Area
C1413 Front Speed Sensor RH Output Malfunction Any of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Front speed sensor RH

·

Front speed sensor rotor RH (Front axle hub sub-assembly RH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector

·

Skid control sensor wire RH


C1414 Front Speed Sensor LH Output Malfunction Any of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Front speed sensor LH

·

Front speed sensor rotor LH (Front axle hub sub-assembly LH)

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector

·

Skid control sensor wire LH



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CHECK FOR INTERMITTENT PROBLEMS


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Normal or Error Normal Error: Momentary interruption
FL Speed Open Front speed sensor LH open detection Normal or Error Normal Error: Momentary interruption
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Speed Open
FL Speed Open
50003 105 200,201
OK:

Normal (There are no momentary interruptions).


HINT:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FRONT SPEED SENSOR)

NG

4.CHECK FRONT SPEED SENSOR INSTALLATION
2.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2
g.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

4.CHECK FRONT SPEED SENSOR INSTALLATION
3.RECONFIRM DTC

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTCs C1413 and C1414 are not output
DTCs C1413 and/or C1414 are output



DTCs C1413 and C1414 are not output

DTCs C1413 and/or C1414 are output

4.CHECK FRONT SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C168336C15
1.994,1.633 2.181,1.795 0.186,0.161 10 *c 0.685,0.198 0.871,0.359 0.186,0.161 10 *a 2.296,0.198 2.482,0.359 0.186,0.161 10 *b
*a Normal
*b Abnormal
*c Clearance


Check the speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR (w/ VSC)>INSTALLATION

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

5.INSPECT FRONT SPEED SENSOR TIP

NG

5.INSPECT FRONT SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.




Result:
Proceed to
OK
NG



OK

6.INSPECT FRONT AXLE HUB SUB-ASSEMBLY

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

6.INSPECT FRONT AXLE HUB SUB-ASSEMBLY
a.

Remove the front axle hub sub-assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the front speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>TEST MODE PROCEDURE


HINT:
·

The front speed sensor rotor is incorporated into the front axle hub sub-assembly.

·

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub sub-assembly.




c.

Reinstall the front speed sensor and the front axle hub sub-assembly.

for the front speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR (w/ VSC)>INSTALLATION

for the front axle hub sub-assembly: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>INSTALLATION


Result:
Proceed to
OK
NG



OK

7.INSPECT SKID CONTROL SENSOR WIRE

NG

CLEAN OR REPLACE FRONT AXLE HUB SUB-ASSEMBLY

7.INSPECT SKID CONTROL SENSOR WIRE
a.

Turn the ignition switch off.


b.

Install the front axle hub and front disc.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>INSTALLATION




e.
C269772C07
0.115,0.781 0.333,1 0.219,0.219 2.833,0.615 3.167,0.833 0.333,0.219 0.104,2.573 0.333,2.792 0.229,0.219 2.833,2.573 3.177,2.792 0.344,0.219 2.833,2.323 3.177,2.542 0.344,0.219 0.104,2.313 0.333,2.531 0.229,0.219 0.938,0.885 0.854,0.219 0.854,0.219 0.74,0.219 true 1.24,0.875 1.333,0.208 1.333,0.208 1.438,0.208 true 0.948,2.583 0.854,1.979 0.854,1.979 0.75,1.979 true 1.26,2.583 1.344,2 1.344,2 1.438,2 true 2.219,0.896 2.167,0.417 2.167,0.417 2.083,0.417 true 2.396,0.927 2.417,0.25 2.417,0.25 2.5,0.25 true 2.5,2.594 2.667,2.167 2.667,2.167 2.833,2.167 true 2.521,2.677 2.708,3.208 2.708,3.208 2.833,3.208 true 1.698,2.979 1.698,2.875 1.698,2.875 2.094,2.625 true 1.917,3.208 2.125,2.656 true 0.344,3.063 0.427,2.958 0.427,2.958 0.969,2.656 true 1.229,3.156 1.229,2.667 true 3.177,0.844 3.396,1.021 0.219,0.177 10 false *A 0.073,0.073 0.385,0.229 0.313,0.156 10 false *1 1.031,1.344 1.344,1.5 0.313,0.156 10 false *a 2.26,1.969 2.573,2.125 0.313,0.156 10 false *b 2.948,2.833 3.26,2.99 0.313,0.156 10 false *c 0.49,0.146 0.792,0.333 0.302,0.188 10 false FR- 1.75,0.323 2.115,0.5 0.365,0.177 10 false FR+ 0.177,0.813 0.333,1.01 0.156,0.198 10 false A 2.917,0.656 3.25,0.833 0.333,0.177 10 false B3 0.375,0.927 0.635,1.104 0.26,0.177 10 false *A 0.302,1.896 0.792,2.104 0.49,0.208 10 false FL- *C 1.5,1.906 2.104,2.094 0.604,0.188 10 false FL+ *C 0.177,2.604 0.333,2.802 0.156,0.198 10 false B 2.885,2.604 3.177,2.781 0.292,0.177 10 false A21 0.76,2.948 0.938,3.135 0.177,0.188 10 false *a 2.302,3.208 2.521,3.417 0.219,0.208 10 false *b 3.219,2.615 3.417,2.781 0.198,0.167 10 false *C 2.917,0.896 3.083,1.083 0.167,0.188 10 false *c 1.5,0.125 1.865,0.302 0.365,0.177 10 false FR+ 2.563,0.177 2.865,0.365 0.302,0.188 10 false FR- 2.896,2.083 3.427,2.281 0.531,0.198 10 false FL- *C 1.479,2.99 2.021,3.177 0.542,0.188 10 false FL+ *C 0.385,2.604 0.583,2.771 0.198,0.167 10 false *C 2.927,2.354 3.219,2.531 0.292,0.177 10 false B4 3.219,2.365 3.417,2.531 0.198,0.167 10 false *B 2.906,3.125 3.375,3.302 0.469,0.177 10 false FR- *B 1.656,3.24 2.177,3.396 0.521,0.156 10 false FR+ *B 1.01,3.156 1.479,3.333 0.469,0.177 10 false FR+ *B 0.104,3.073 0.573,3.25 0.469,0.177 10 false FR- *B 0.177,2.333 0.333,2.531 0.156,0.198 10 false A 0.385,2.333 0.583,2.5 0.198,0.167 10 false *B
*A for RH (Type A)
*B for RH (Type B)
*C for LH
*1 Skid Control Sensor Wire
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)
*c Male


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH (Type A)
Tester Connection Condition Specified Condition
B3 male connector 1 (FR-) - A-1 (FR-) Always Below 1 Ω
B3 male connector 1 (FR-) or A-1 (FR-) - Body ground Always 10 kΩ or higher
B3 male connector 2 (FR+) - A-3 (FR+) Always Below 1 Ω
B3 male connector 2 (FR+) or A-3 (FR+) - Body ground Always 10 kΩ or higher
A-1 (FR-) - A-3 (FR+) Always 10 kΩ or higher

for RH (Type B)
Tester Connection Condition Specified Condition
B4 male connector 1 (FR-) - A-1 (FR-) Always Below 1 Ω
B4 male connector 1 (FR-) or A-1 (FR-) - Body ground Always 10 kΩ or higher
B4 male connector 3 (FR+) - A-3 (FR+) Always Below 1 Ω
B4 male connector 3 (FR+) or A-3 (FR+) - Body ground Always 10 kΩ or higher
A-1 (FR-) - A-3 (FR+) Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A21 male connector 1 (FL-) - B-1 (FL-) Always Below 1 Ω
A21 male connector 1 (FL-) or B-1 (FL-) - Body ground Always 10 kΩ or higher
A21 male connector 3 (FL+) - B-3 (FL+) Always Below 1 Ω
A21 male connector 3 (FL+) or B-3 (FL+) - Body ground Always 10 kΩ or higher
B-1 (FL-) - B-3 (FL+) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

NG

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.



c.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


d.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


e.

Disconnect the A and/or B front speed sensor connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH (Type A)
Tester Connection Condition Specified Condition
A42-31 (FR+) - B3-2 (FR+) Always Below 1 Ω
A42-30 (FR-) - B3-1 (FR-) Always Below 1 Ω
A42-31 (FR+) or B3-2 (FR+) - Body ground Always 10 kΩ or higher
A42-30 (FR-) or B3-1 (FR-) - Body ground Always 10 kΩ or higher

for RH (Type B)
Tester Connection Condition Specified Condition
A42-31 (FR+) - B4-3 (FR+) Always Below 1 Ω
A42-30 (FR-) - B4-1 (FR-) Always Below 1 Ω
A42-31 (FR+) or B4-3 (FR+) - Body ground Always 10 kΩ or higher
A42-30 (FR-) or B4-1 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A42-18 (FL+) - A21-3 (FL+) Always Below 1 Ω
A42-17 (FL-) - A21-1 (FL-) Always Below 1 Ω
A42-18 (FL+) or A21-3 (FL+) - Body ground Always 10 kΩ or higher
A42-17 (FL-) or A21-1 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (FR+/FL+ TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (FR+/FL+ TERMINAL)
a.
C269767C05
1.583,0.115 1.781,0.313 0.198,0.198 1.583,0.396 1.781,0.583 0.198,0.188 1.938,1.344 2.76,1.49 2.76,1.49 2.76,1.594 false 1.802,0.063 2.115,0.219 0.313,0.156 10 false *A 1.802,0.365 2.115,0.521 0.313,0.156 10 false *B 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 1.635,0.135 1.792,0.333 0.156,0.198 10 false A 1.635,0.406 1.792,0.604 0.156,0.198 10 false B 2.563,1.635 3.021,1.833 0.458,0.198 10 false FR+ 2.563,1.813 2.875,2.01 0.313,0.198 10 false FL+ 2.813,1.615 3.125,1.813 0.313,0.198 10 false *A, 2.813,1.802 3.125,2 0.313,0.198 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)


Reconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
A-3 (FR+) - Body ground Ignition switch ON 11 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
B-3 (FL+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG