Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  Fuel Injection System  


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION

·

After replacing an fuel injector, the ECM needs registration.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION



PROCEDURE

1.CHECK INJECTOR COMPENSATION CODE
a.

Check the injector compensation code.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Injector Compensation
50005 234 148
Result:
Result Proceed to
Except below A
Compensation codes of the installed injector assemblies are the same as the compensation codes registered in the ECM B




A

2.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

B

3.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 3)
2.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation codes.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Injector Compensation
50005 234 148

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Pilot Quantity Learning
50005 234 235

Result:
Proceed to
NEXT



NEXT

3.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 3)
3.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 3)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Common Rail (All).


d.

Take a snapshot of the following Data List items.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.

·

Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.




Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #8 AND INJECTION VOLUME)
4.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #8 AND INJECTION VOLUME)
a.

Check Injection Feedback Val #1 to #8 and Injection Volume in the snapshot taken in procedure 3 when the engine was idling and at 4000 rpm with no load.

Result:
Result Proceed to
Injection Feedback Val for at least one cylinder is more than 3.0 mm3/st A
Injection Volume is less than 5.5 mm3/st at 3000 rpm B
Except above C


HINT:
·

When there is a problem with the operation of an fuel injector due to foreign matter in the inside of the fuel injector, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.

·

The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

5.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

B

22.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

C

21.READ VALUE USING GTS (INJECTION VOLUME)
5.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #8.

Powertrain > Engine and ECT > Active Test
Active Test Display
Check the Cylinder Compression
Data List Display
Engine Speed of Cyl #1
Engine Speed of Cyl #2
Engine Speed of Cyl #3
Engine Speed of Cyl #4
Engine Speed of Cyl #5
Engine Speed of Cyl #6
Engine Speed of Cyl #7
Engine Speed of Cyl #8
50004 234 111 379,380,381,382,383,384,385,386

d.

Check the engine speed during the Active Test.

Result:
Result Proceed to
Except below A
The values of Engine Speed Cyl #1 to #8 are within 10 rpm of each other. B


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

6.CHECK CYLINDER COMPRESSION PRESSURE

B

7.PERFORM PILOT QUANTITY LEARNING
6.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

When compression is low, there may be cracks in the piston or the fuel injector may be installed improperly.



Result:
Proceed to
OK
NG



OK

7.PERFORM PILOT QUANTITY LEARNING

NG

10.CHECK AND REPLACE PARTIAL ENGINE ASSEMBLY
7.PERFORM PILOT QUANTITY LEARNING
a.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Pilot Quantity Learning
50005 234 235

Result:
Proceed to
NEXT



NEXT

8.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #8)
8.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #8)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #8.

Powertrain > Engine and ECT > Data List
Tester Display
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection Feedback Val #5
Injection Feedback Val #6
Injection Feedback Val #7
Injection Feedback Val #8
50003 234 778,779,780,781,782,783,784,785

e.

Read the values.

Standard:
GTS Display Engine Condition* Normal Value
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection Feedback Val #5
Injection Feedback Val #6
Injection Feedback Val #7
Injection Feedback Val #8
Idling -3.0 mm3/st to 3.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 75°C (167°F) or more and the engine should be idled for 1 minute or more.


Result:
Result Proceed to
Injection Feedback Val for at least one cylinder is more than 3.0 mm3/st A
Except above B


HINT:
·

When there is a problem with the operation of an fuel injecyor due to foreign matter in the inside of the fuel injecyor, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.

·

The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

9.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER

B

11.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
9.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
a.

Replace the fuel injector of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/ DPF)>REMOVAL

NOTICE:
·

When replacing the fuel injector for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an fuel injector deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an fuel injector becomes out of position, it is possible that the seal between the fuel injector and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

23.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
10.CHECK AND REPLACE PARTIAL ENGINE ASSEMBLY
a.

Check and replace the engine assembly.


Result:
Proceed to
NEXT



NEXT

11.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
11.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Common Rail Pressure and Target Common Rail Pressure.

Powertrain > Engine and ECT > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Common Rail Pressure
50004 234 90 850,851

d.

Start the engine.


e.

Take a snapshot with the GTS during the Active Test.


f.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Common Rail Pressure) when the "Test the Fuel Leak" Active Test is performed.

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E55
3.604,2.406 3.719,1.927 3.719,1.927 3.792,1.927 false 4.604,2.563 4.948,2.302 4.948,2.302 5.031,2.302 false 3.521,2.542 3.24,1.896 3.24,1.896 3.188,1.896 false 3.583,3.24 3.833,4.313 3.833,4.313 3.979,4.313 false 0.083,1.417 1.448,1.573 1.365,0.156 10 false Active Test Operation 0.083,0.583 1.479,0.781 1.396,0.198 10 false Engine Speed (rpm) 0.083,3.25 1.677,3.49 1.594,0.24 10 false Common Rail Pressure 3.813,1.865 5.75,2.031 1.938,0.167 10 false Target Common Rail Pressure 6.469,4.125 6.865,4.302 0.396,0.177 10 false Time 2.125,2.406 2.865,2.771 0.74,0.365 10 false Less than 10000 kPa 3,4.26 3.688,4.427 0.688,0.167 10 false 2 seconds 5.073,2.208 6.354,2.583 1.281,0.375 10 false Abnormal Common Rail Pressure 2.677,1.042 3.354,1.24 0.677,0.198 10 false Test Start 4.458,1.042 5.125,1.24 0.667,0.198 10 false Test Stop 5.885,1.042 6.563,1.24 0.677,0.198 10 false Test Start 2.083,1.813 3.229,2.135 1.146,0.323 10 false Normal Common Rail Pressure 1.646,0.271 2.021,0.438 0.375,0.167 10 false 2000 1.885,0.833 2.052,1 0.167,0.167 10 false 0 1.75,1.302 2.073,1.469 0.323,0.167 10 false ON 1.698,1.552 2.021,1.719 0.323,0.167 10 false OFF 4.031,4.25 6.344,4.604 2.313,0.354 10 false Pressure Discharge Valve Abnormal Common Rail Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa (102.0 kgf/cm2, 1451 psi).


Result:
Result Proceed to
NG A
OK* B


NOTICE:

*: Even when the results of the Active Test are normal, take a snapshot of vehicle data when the vehicle is accelerating. If "Common Rail Pressure" does not follow "Target Common Rail Pressure", proceed to step 12.

If "Common Rail Pressure" does not follow "Target Common Rail Pressure", the fuel filter may be clogged.


HINT:
·

"Target Common Rail Pressure" means target fuel pressure controlled by the ECM.

·

"Common Rail Pressure" means actual fuel pressure in common rail assembly.

·

If the pressure discharge valve mounted on the common rail assembly is malfunctioning, the actual fuel pressure may change as indicated by "Pressure Discharge Valve Abnormal Common Rail Pressure" in the illustration.

·

The pressure discharge valve operates to discharge fuel pressure when the internal pressure of the common rail exceeds the target fuel pressure.

·

There are 2 fuel pressure sensor circuits and both of them display the same value. If the difference between Common Rail Pressure exceeds 10000 kPa (102 kgf/cm2, 1451 psi) for 2 seconds or more, it is necessary to inspect or repair the wiring for the fuel pressure sensor.





A

12.INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE)

B

20.READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)
12.INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE)
a.

Enter the following menus: Powertrain / Engine and ECT / Utility / Pressure Discharge Valve Check.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION

Powertrain > Engine and ECT > Utility
Tester Display
Pressure Discharge Valve Check
50005 234 2109

b.

Select "Always Closed Check".


c.

Press "Next".


d.

Read the Value of fuel pressure values.

OK:

Fuel pressure is properly maintained.


HINT:
·

If the fuel pressure cannot be maintained, the pressure discharge valve may not have a tight seal.

·

If the fuel pressure is being properly maintained, there are no problems with the sealing properties of the high-pressure fuel system. Therefore, an insufficient supply of fuel due to the fuel filter being clogged, or squashed or blocked low-pressure fuel pipes or hoses may be causing the reduction in the common rail pressure.




Result:
Proceed to
OK
NG



OK

13.INSPECT CLOGGED FUEL PIPE

NG

18.REPLACE COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE)
13.INSPECT CLOGGED FUEL PIPE
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target Common Rail Pressure and Common Rail Pressure.

Powertrain > Engine and ECT > Data List
Tester Display
Target Common Rail Pressure
Common Rail Pressure
50003 234 850,851

d.

With no load after the engine is warmed up, take a snapshot when idling and vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.


e.

Check the Target Common Rail Pressure and Common Rail Pressure value.

A261221E21
0.031,1.708 1.365,2.083 1.333,0.375 10 false Target Common Rail Pressure 3.854,2.125 6.438,2.271 2.583,0.146 10 false Normal Common Rail Pressure 3.75,0.229 5.375,0.573 1.625,0.344 10 false Abnormal Common Rail Pressure*1 0.115,0.031 2.646,0.198 2.531,0.167 10 false Common Rail Pressure During Idling 1.083,2.406 3.75,2.75 2.667,0.344 10 false Pressure varies periodically with a period of approximately 2 seconds or more 5.906,1.104 7.146,1.885 1.24,0.781 10 false Normal Condition: +/-5000 kPa (Idling after Engine Warmed Up)

Result:
Result Proceed to
While idling the vehicle, "Common Rail Pressure" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1 A
"Common Rail Pressure" is normal while idling the vehicle, but "Common Rail Pressure" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear*2
Except above B


NOTICE:
·

*1: The cause may be a squashed or blocked fuel pipe or hose.

·

*2: The cause may be a clogged fuel filter element assembly.





A

14.REPAIR OR REPLACE CLOGGED FUEL LINE

B

15.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
14.REPAIR OR REPLACE CLOGGED FUEL LINE
a.

Repair or replace the clogged (including frozen fuel) fuel pipe.


b.

Replace the fuel filter element assembly.

HINT:

If "Common Rail Pressure" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel filter element assembly.



Result:
Proceed to
NEXT



NEXT

19.BLEED AIR FROM FUEL SYSTEM
15.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP (w/ DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.BLEED AIR FROM FUEL SYSTEM
16.BLEED AIR FROM FUEL SYSTEM

b.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM (w/ DPF)>ON-VEHICLE INSPECTION

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.



Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END

18.REPLACE COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE)
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL (w/ DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

19.BLEED AIR FROM FUEL SYSTEM
19.BLEED AIR FROM FUEL SYSTEM

b.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM (w/ DPF)>ON-VEHICLE INSPECTION

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.



Result:
Proceed to
NEXT



NEXT

20.READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)
20.READ VALUE USING GTS (COMMON RAIL PRESSURE AND TARGET COMMON RAIL PRESSURE)
a.

Check Common Rail Pressure and Target Common Rail Pressure in the snapshot taken in procedure 3 when the engine was idling.

Result:
Result Proceed to
Difference between Common Rail Pressure and Target Common Rail Pressure is 5000 kPa (51.0 kgf/cm2, 725 psi) or more B
Except above A




A

END

B

15.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
21.READ VALUE USING GTS (INJECTION VOLUME)
a.

Check Injection Volume in the snapshot taken in procedure 3 when the engine was idling.

Result:
Result Proceed to
Injection Volume while idling after engine warm up is more than 10 mm3/st A
Except above B




A

22.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

B

11.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
22.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the fuel injectors of all cylinders.

Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/ DPF)>REMOVAL

NOTICE:
·

When replacing the fuel injector for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an fuel injector deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an fuel injector becomes out of position, it is possible that the seal between the fuel injector and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

23.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
23.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

24.BLEED AIR FROM FUEL SYSTEM
24.BLEED AIR FROM FUEL SYSTEM

b.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM (w/ DPF)>ON-VEHICLE INSPECTION

HINT:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.



Result:
Proceed to
NEXT



NEXT

25.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
25.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation codes.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Injector Compensation
50005 234 239

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION

Powertrain > Engine and ECT > Utility
Tester Display
Pilot Quantity Learning
50005 234 235

Result:
Proceed to
NEXT



NEXT

11.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)