Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › 2017.01–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  P0234  Turbocharger / Supercharger Overboost Condition  P0299  Turbocharger / Supercharger Underboost  P1251  Turbocharger / Supercharger Overboost Condition (Too High)  


DESCRIPTION

The variable nozzle vane type turbocharger operates the vacuum type actuator and controls the nozzle vane by using the VRV, which is controlled by the ECM. At a low to medium vehicle speed, when the nozzle vane moves in the closing direction and the exhaust gas rate of flow becomes faster, the engine torque increases. At a high vehicle speed, when the nozzle vane moves in the opening direction, the exhaust pressure decreases. This leads to improved fuel consumption and engine output.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0234 Turbocharger / Supercharger Overboost Condition When turbocharger boost pressure continues to be higher than ECM's target boost pressure.
(1 trip detection logic)
·

Vacuum regulating valve

·

Turbocharger sub-assembly

·

Vacuum hose

·

Mass air flow meter

·

ECM


Comes on DTC stored
P0299 Turbocharger / Supercharger Underboost When turbocharger boost pressure continues to be lower than ECM's target boost pressure.
(2 trip detection logic)
·

Vacuum regulating valve

·

Turbocharger sub-assembly

·

Vacuum hose

·

Mass air flow meter

·

ECM


Comes on DTC stored
P1251 Turbocharger / Supercharger Overboost Condition (Too High) When turbocharger boost pressure is higher than boost pressure for a short time in which there was possibility of engine damage.
(1 trip detection logic)
·

Vacuum regulating valve

·

Turbocharger sub-assembly

·

Vacuum hose

·

Mass air flow meter

·

ECM


Comes on DTC stored

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0234, P0299 AND/OR P1251)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

d.

Read DTCs.

Result:
Result Proceed to
P0234, P0299 and/or P1251 are output A
P0234, P0299 and/or P1251 and other DTCs are output B




A

2.CHECK INTAKE AND EXHAUST SYSTEM

B

2.CHECK INTAKE AND EXHAUST SYSTEM
a.

Check the intake and exhaust system modifications.

OK:

No modifications.



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION OF VACUUM HOSE

NG

REPAIR OR REPLACE INTAKE AND/OR EXHAUST SYSTEM

3.CHECK CONNECTION OF VACUUM HOSE
a.

Check the connections of the vacuum hoses of the turbocharger system.

OK:

The vacuum hoses are correctly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK VACUUM (VACUUM REGULATING VALVE - TURBOCHARGER)

NG

REPAIR OR REPLACE VACUUM HOSE

4.CHECK VACUUM (VACUUM REGULATING VALVE - TURBOCHARGER)
a.

Using a three-way connector, connect a vacuum gauge to the hose between the vacuum regulating valve (VRV) and turbocharger.


b.

Warm up the engine coolant temperature to above 75°C (167°F).


c.

Check the vacuum while idling.

Result:
Vacuum Proceed to
0 kPa (0 mmHg, 0 in.Hg) to 50 kPa (375 mmHg, 14.8 in.Hg) A
Above 50 kPa (375 mmHg, 14.8 in.Hg) B




A

5.INSPECT VACUUM REGULATING VALVE ASSEMBLY (RESISTANCE)

B

7.INSPECT TURBOCHARGER SUB-ASSEMBLY
5.INSPECT VACUUM REGULATING VALVE ASSEMBLY (RESISTANCE)
a.
A160397C01
0.104,0.115 0.417,0.313 0.313,0.198 10 false *a
*a Component without harness connected
(Vacuum Regulating Valve)


Disconnect the Vacuum Regulating Valve (VRV) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11 to 13 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (VACUUM REGULATING VALVE - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (VACUUM REGULATING VALVE - ECM)
a.
A311455C03
1.469,0.25 1.865,0.521 0.396,0.271 1.354,2.219 1.75,2.49 0.396,0.271 2.583,4.177 2.396,3.448 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 0.146,2.167 0.458,2.365 0.313,0.198 10 false *b 1.552,0.313 1.865,0.51 0.313,0.198 10 false C91 1.438,2.271 1.75,2.469 0.313,0.198 10 false C39 2.635,4.115 3.167,4.313 0.531,0.198 10 false 85 (VN)
*a Front view of wire harness connector
(to Vacuum Regulating Valve)
*b Front view of wire harness connector
(to ECM)


Disconnect the VRV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C91-2 - C39-85 (VN) Always Below 1 Ω
C91-2 or C39-85 (VN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT TURBOCHARGER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
OK
NG



OK

8.INSPECT MASS AIR FLOW METER

NG

8.INSPECT MASS AIR FLOW METER

Result:
Proceed to
OK
NG



OK

NG